Boletim
An adjusting element installed in the soft-top bow bearing can potentially cause chafing on the convertible top.
🔔 Crie uma conta gratuita para receber alertas por e-mail sobre Mini Hatch (todas as gerações)
Os boletins técnicos (TSB) são instruções de reparação que os fabricantes enviam aos concessionários sobre problemas conhecidos. Não são recalls de segurança, mas muitas vezes confirmam um defeito.
An adjusting element installed in the soft-top bow bearing can potentially cause chafing on the convertible top.
It is possible that the guide stem (aka rotational axis) on the wind deflector can break, upon removal and or during installation.
Installation of Right-Hand Drive Stering Spindle in Left-Hand Drive Vehicle is No Longerr Required
ROLLER SUNBLIND RETURN: MINI AG has requested the inspection and return of the following part number - 54 10 9 451 245. Stock should not be sold or installed on any vehicle.
MINI PARTS BULLETIN TEC245: Stabilizer Support Inspection BMW AG has requested the inspection of the following part numbers: 31 35 6 778 827. Stock should not be sold or installed on any vehicle until inspection has been completed.
MINI PARTS BULLETIN TEC250: Mechanical Belt Tensioner Inspection BMW AG has requested the inspection of the following part numbers: 11 28 8 580 360. Stock should not be sold or installed on any vehicle until inspection has been completed.
MINI PARTS BULLETIN TEC228: Control Unit RDC Inspection BMW AG has requested the inspection of the following part number: 36 10 6 868 194 Stock should not be sold or installed on any vehicle until inspection has been performed. Concerned are all parts produced from January 02 2020 to February 16 2020. Please return all affected part(s) to your facing Regional Distribution Center (RDC).
MINI PARTS BULLETIN TEC233: Fan Shroud Inspection BMW AG has requested the inspection of the following part number: 17 42 8 742 712 Stock should not be sold or installed on any vehicle until inspection has been completed. Concerned are all parts delivered and shipped so far. Please return all affected part(s) to your facing Regional Distribution Center (RDC).
MINI PARTS BULLETIN TEC213 Bowden Cable Inspection: BMW AG has requested the inspection of the following part numbers: 51 21 7 296 459 / 51 21 7 320 309 / 51 21 7 364 596 Stock should not be sold or installed on any vehicle until inspection has been completed. Concerned are all parts delivered and shipped so far. Please return all part(s) to your facing Regional Distribution Center (RDC).
MINI PARTS BULLETIN TEC214 Intake Duct Return: BMW AG has requested the return of the following part number: 17 51 1 524 439 Stock should not be sold or installed on any vehicle. Concerned are all parts delivered and shipped so far. Please return all part(s) to your facing Regional Distribution Center (RDC).
BMW Parts Bulletin TEC195 USB Socket Inspection BMW AG has requested the inspection of the following part numbers: 84 10 8 711 938 / 84 10 8 711 939 / 84 10 8 711 940 Stock should not be sold or installed on any vehicle until inspection has been completed.
MINI PARTS BULLETIN TEC152 Tank Breather Valve Return. MINI AG has requested the inspection of the following part number: 13 90 7 621 174. Stock should not be sold or installed on any vehicle.
"White Wear Marks on Canvas Top. Wear marks appear on the convertible top on the left and/or right side C-pillar areas. A For vehicles produced to December 12, 2011 1. Replace the defective canvas convertible top. Refer to ISTA Repair Instruction 54 34 120, ""Replacing soft top fabric."" Note: The following repair steps must be performed before the new top is installed to prevent a repeat repair for wear marks. 2. With the defective canvas cover removed, the current main pillars must be replaced. Refer to ISTA Repair Instruction 54 34 996, ""Replacing left or right main pillar."" 3. The current locking mechanisms and bump stops must be replaced as well. Refer to ISTA Repair Instruction 54 34 196, ""Removing and installing / replacing both stowage locks."" The repair kit* needed is listed below. 7. Reinstall the removed parts in the reverse order of their removal. 8. Operate the top several times to quality check the repair."
WIND DEFLECTOR DAMAGED. A rattle may be heard from the wind deflector while driving or, the retaining pins may be broken when installing wind deflector. Retaining pins in wind deflector are broken.
SERVICE ACTION: RUBBER STRIP ON REAR SIDE WINDOW TRIM IS CRACKED. The rubber strip on the rear side window trim may crack. In some cases a gap may be evident on the rubber trim strip. Results are cosmetic- no water leakage or sound intrusion. Combination of unfavorable materials.
Water Ingress In Footwell Area From A/C Condensate Drain This Service Information bulletin supersedes SI M64 01 16 dated March 2016.. Damp front foot-well carpet after long period of air conditioning use. Musty odor in the vehicle (moldy, old socks, laundry room). The A/C condensate drain hose is blocked by the heatshield. The A/C condensate drain hose is not attached properly to the housing. The A/C condensate drain hose was damaged during installation or previous repair.
Mini: Check svs function. On certain vehicles, the voice input system (svs sa 620) does not function. The svs was not installed in the vehicles. *pe
Coolant expansion tank leaks. Launch up to 01/03 production. *tt
If MINI Personal Assistant is active in the vehicle, once the customer exits the vehicle and a new key cyclestarts, the MINI Personal Assistant is deactivated and no longer available.
During vehicle start-up the Secure Element (SE) of the BCP may fail causing communication errors. TheCheck Control message Drive carefully. Driving stabilisation. will appear. In addition, the fault memoryentries below will be stored within 40 seconds of each other. ACSM: 02010A - Coding: Coding data not qualified VIP: 02390A - VIP control unit: Coding data not released, signature IB: 02290A - DSC control unit: Coding data not released, signature HKFM: 020D0A - HKFM: Coding data are not qualified
Retorno PDC da Unidade de Controlo
During vehicle start-up the Secure Element (SE) of the BCP may fail causing communication errors. TheCheck Control message Drive carefully. Driving stabilisation. will appear. In addition, the fault memoryentries below will be stored within 40 seconds of each other. ACSM: 02010A - Coding: Coding data not qualified VIP: 02390A - VIP control unit: Coding data not released, signature IB: 02290A - DSC control unit: Coding data not released, signature HKFM: 020D0A - HKFM: Coding data are not qualified
During vehicle start-up the Secure Element (SE) of the BCP may fail causing communication errors. TheCheck Control message Drive carefully. Driving stabilisation. will appear. In addition, the fault memoryentries below will be stored within 40 seconds of each other. ACSM: 02010A - Coding: Coding data not qualified VIP: 02390A - VIP control unit: Coding data not released, signature IB: 02290A - DSC control unit: Coding data not released, signature HKFM: 020D0A - HKFM: Coding data are not qualified
Adhesive Film Return
Devolução do Jogo de Juntas
Fontes: NHTSA (Estados Unidos, domínio público), Transport Canada (Open Government Licence – Canada), DVSA (Reino Unido, Open Government Licence v3.0), RappelConso e Safety Gate da UE (França, Licence Ouverte 2.0), MLIT (Japão, Licença de Dados Públicos 1.0) e MOLIT (Coreia do Sul, car.go.kr).