免费阅读 · 免费账户即可贡献Anticars(2000)的继任者

BMW 7系列 E32

1986–1994 · 已记录5项缺陷 · 4个市场
车型年份
市场全部NA
召回严重内饰NA

Airbag

On certain 318I, 318IS, 325I, 325IS, 525I, 525IT, 535I, 735I, 735IL, 750IL, 850I and M5, the locking tab for the airbag contact ring in the steering wheel assembly could break without warning. If this happens it is possible that the contact ring wiring could break. This would cause the readiness indicator lamp ("SRS" or "AIRBAG") to illuminate and in such a case the airbag would not be available for deployment in a frontal impact. Correction: Locking tab will be replaced with one of a different design.

加拿大交通部1996年10月7日1996159车型年份 1991–1992以原文(英语)显示 · 翻译待完成查看详情 →
召回严重内饰NA

安全气囊:前置

位于方向盘组件内的安全气囊接触环锁扣可能会无预警地损坏。

NHTSA · 美国1996年7月1日96V110000车型年份 1991–1992自动翻译 · 原文:英语查看详情 →
召回严重发动机NA

燃油系统

在部分318I、318IC、318IS、325IC、325IS、325IX、525I、535I、735I和735IL车型上,燃油供油软管可能因发动机舱温度而变硬并逐渐"定型"。若发生这种"定型",软管与接头之间可能出现渗漏,因为卡箍无法提供足够的密封力来补偿软管的硬化。在有点火源的情况下,燃油渗漏可能导致发动机舱起火。 纠正措施:燃油供油软管及相关卡箍将更换为新设计的产品。

加拿大交通部1994年5月30日1994096车型年份 1989–1993自动翻译 · 原文:英语查看详情 →
召回严重发动机NA

燃油系统,汽油:输送:软管、管路/管道及接头

供油软管会随时间变硬并发生"定型"(永久变形),从而导致燃油在软管与发动机接头的连接处渗漏。用于将软管固定在接头上的卡箍无法补偿供油软管的硬化。

NHTSA · 美国1994年4月11日94V066000车型年份 1989–1993自动翻译 · 原文:英语查看详情 →
召回中等内饰NA

Heater 与除霜器

在某些车辆上,节温器、水泵或风扇皮带等冷却系统部件失效,可能导致冷却液温度和系统压力显著升高。系统压力增大可能使暖风芯体端盖出现裂纹或接缝开裂,从而使高温冷却液从暖风芯体喷出。这些高温液体可能接触车内乘员,造成人身伤害,和/或导致车内玻璃表面起雾。 纠正措施:更换为新设计的散热器盖,以避免冷却系统内压力过度升高。

加拿大交通部1998年10月14日1998197车型年份 1988–1993自动翻译 · 原文:英语查看详情 →
召回中等发动机NA

发动机及发动机冷却系统:冷却系统

车辆描述:乘用车。冷却系统组件(如恒温器、水泵或风扇带)的故障或故障可能导致冷却液温度和系统压力显著升高。如果司机未察觉到严重过热的迹象,可能会导致冷却系统部件损坏或失效。

NHTSA · 美国1998年8月4日98V178000车型年份 1988–1993自动翻译 · 原文:英语查看详情 →
召回中等发动机NA

Engine

在部分318IC、318IS、318TI、325I、325IC、325IS、525I、525IT、530I、530IT、540I、740I、740IL、840CI和M3车型上,定速巡航拉线和节气门拉线连接在节气门体上的同一个节气门阀驱动杆上。任一拉线上的塑料衬套都可能断裂,导致拉线外套管与衬套脱开。在未启用定速巡航的情况下踩下油门踏板,外套管可能会卡在断裂衬套的边缘,使节气门阀保持部分开启。如果发生这种情况,车辆可能无法按预期减速,从而可能导致碰撞事故。 更正措施:在每根拉线的外套管上加装弹簧卡夹,以防止其从衬套上脱落。

加拿大交通部1997年10月9日1997173车型年份 1993自动翻译 · 原文:英语查看详情 →
召回中等发动机NA

Vehicle speed control

The cruise control and throttle cables are attached to the same throttle valve actuating lever at the throttle housing. It is possible that the plastic bushing on either cable could break due to environmental influences coupled with vibration. If the bushing breaks, the outer cable housing can separate from the bushing. In this case, during application of the throttle pedal without cruise control being engaged, the outer tube could catch on the edge of the broken bushing.

NHTSA · 美国1997年8月19日97V131000车型年份 1993以原文(英语)显示 · 翻译待完成查看详情 →
召回中等电气NA

Lights And Instruments

On certain 325I, 325IC, 325IS, 525I, 525IT, 530I, 530IT, 535I, 540I, 735I, 735IL, 740I, 740IL and 750I, the brake light switch may fail due to a reduction of contact force on the "snap contact" system which the switch incorporates. This could cause heat induced distortion of the plastic internal switch parts in the area of the electrical contacts. This could cause the switch to remain either in the ON or the OFF position resulting in the brake lights being continuously illuminated or inoperative regardless of brake pedal operation. Correction: Switch will be replaced with on that utilizes a different contact system.

加拿大交通部1996年10月7日1996158车型年份 1990–1993以原文(英语)显示 · 翻译待完成查看详情 →
召回中等制动NA

Exterior lighting:Brake lights:Switch

The brake light switch can fail allowing the switch to remain in the "brake lights off" position or in the "brake lights on" position.

NHTSA · 美国1996年7月1日96V111000车型年份 1990–1993以原文(英语)显示 · 翻译待完成查看详情 →
召回中等发动机NA

Engine

On certain 740IA and 740ILA vehicles, the inner throttle cable could break due to a smaller than specification bend in the cable tube. If this were to occur, throttle control would be lost and the engine would return to or remain at idle. Correction: Throttle cable will be replaced with one meeting BMW specifications.

加拿大交通部1994年4月25日1994081车型年份 1993以原文(英语)显示 · 翻译待完成查看详情 →
召回中等发动机NA

Vehicle speed control:Cables

The throttle cable's tube (outer casing) contains a bend that leads to increased loading of the inner cable, causing it to break.

NHTSA · 美国1994年1月3日94V022000车型年份 1993以原文(英语)显示 · 翻译待完成查看详情 →
召回中等发动机NA

Engine

On certain 535I, 535IA, 735IA, 735ILA vehicles, the nut which secures the throttle valve shaft may not have been tightened with sufficient torque. If the nut were to loosen, it is possible that movement of the throttle valve might be impaired. If this should occur, the vehicle might not decelerate as expected after the gas pedal is released and loos of vehicle control could result. Correction: Vehicles will be inspected and affected throttle housings with undertorqued throttle valve retaining nuts will be replaced.

加拿大交通部1992年10月13日1992129车型年份 1991以原文(英语)显示 · 翻译待完成查看详情 →
召回中等发动机NA

Vehicle speed control

Some of these vehicles are equipped with a throttle housing on which the throttle valve shaft retaining nut was not sufficiently tightened.

NHTSA · 美国1992年7月10日92V101000车型年份 1991以原文(英语)显示 · 翻译待完成查看详情 →
召回中等内饰NA

Seats And Restraints

On certain 525I, 535I, 735I, 735IL and 750IL vehicles, the front seat center fold-down armrest may contact and damage the seatbelt buckle if the seat back is moved forward to an upright position while the armrest is locked in the down position (horizontal). If this occurs, the release button may be held in the down position, preventing the seatbelt from being latched during the buckle-up operation. Non-latching of the seatbelts will increase the risk of personal injury in the event of a crash. Correction: Front seat safety belt buckles will be replaced with shorter ones that are not susceptible to damage by contact with the armrest.

加拿大交通部1990年2月27日1990037车型年份 1988–1990以原文(英语)显示 · 翻译待完成查看详情 →
召回中等内饰NA

Seat belts:Front:Buckle assembly

Under certain conditions, front seat center, fold-down arm rest may contact the safety belt buckle, causing damage to the release button and preventing the belt tongue from latching when buckling up.

NHTSA · 美国1990年1月30日90V016000车型年份 1988–1990以原文(英语)显示 · 翻译待完成查看详情 →
召回中等发动机NA

Emissions

Certain 750IL vehicles fail to comply with the requirements of CMVSS 1103 - Exhaust Emissions.

加拿大交通部1989年5月2日1989063车型年份 1988–1989以原文(英语)显示 · 翻译待完成查看详情 →
召回中等发动机NA

Emissions

Certain 750IL vehicles fail to comply with the requirements of CMVSS 1103 - Exhaust Emissions

加拿大交通部1989年5月2日1989062车型年份 1988–1989以原文(英语)显示 · 翻译待完成查看详情 →
召回中等发动机NA

Engine

On certain 750IL vehicles, during the assembly process, the gas pedal may not have been properly attached to the floor pan. If the gas pedal is operated in a rough or erratice manner, it may become stuck between the gas pedal stop (on the floor pan) and the carpeting on the transmission tunnel. If this occurs, the pedal might not return fully to the idle position when the driver's foot is removed and loss of control could result. Application of the brake pedal will close the throttle on this model of vehicle. Correction: Accelerator pedal will be inspected and tightened to the floor is required. Also, a modified pedal stop will be installed.

加拿大交通部1989年4月6日1989046车型年份 1988–1989以原文(英语)显示 · 翻译待完成查看详情 →
召回中等电气NA

电气系统

在某些325E、325ES、528E、535I、635CSI和735I车型上,中央高位制动灯可能会产生足够的电负荷,导致制动灯开关过热,最终使开关内部的塑料部件熔化。这可能导致开关柱塞卡死在接通或断开位置。这将使制动灯无论是否踩下制动踏板都处于永久常亮或常灭状态。纠正措施:受影响车辆将安装具有更高电流负载能力的制动灯开关。

加拿大交通部1986年11月27日1986134车型年份 1986–1987自动翻译 · 原文:英语查看详情 →
召回轻微内饰NA

Seats And Restraints

On certain 725I, 735IA and 750IL vehicles, on the front seats, the seatbacks may not have been fully seated on the recliner arms. This could result in looseness of, or noise in the seat. In extreme cases, during a severe rear impact, the seatback may not support the occupant and increase the risk of injury. Correction: Seatbacks will be inspected and properly seated if required.

加拿大交通部1988年8月25日1988124车型年份 1988以原文(英语)显示 · 翻译待完成查看详情 →
召回轻微内饰NA

Seats

The driver and/or passenger seatbacks may not have been fully attached to the seat base reclining arms (attaching brackets).

NHTSA · 美国1988年8月11日88V135000车型年份 1988以原文(英语)显示 · 翻译待完成查看详情 →

来源:NHTSA(美国,公有领域)、加拿大交通部(加拿大开放政府许可)、DVSA(英国,开放政府许可 v3.0)、RappelConso 与欧盟 Safety Gate(法国,开放许可 2.0)、日本国土交通省(公共数据许可1.0)、韩国国土交通部(car.go.kr)。