免费阅读 · 免费账户即可贡献Anticars(2000)的继任者

Mazda MX-30

2020– · 1 各代车型 · 已记录1项缺陷 · 4个市场
各代车型

技术服务通报(TSB)是制造商就已知问题发给经销商的维修说明。它们不是安全召回,但常常能证实某个缺陷。

严重程度全部中等轻微
车型年份
通报中等车身NA

通报

描述 部分客户在使用远程发射器锁门和解锁时,可能会出现以下一种或两种症状。症状1:前门外把手的触摸传感器在雨后和/或洗车后无法锁上车门,尽管可以解锁。症状2:前门外把手的触摸传感器无法解锁车门。门外把手的触控传感器用于锁(1)/解锁(2)注意:如果在特定操作后出现问题,请参考TSB 09-046/22(门外把手触摸传感器在特定操作后无法锁定和解锁)。1. [MX-30] 使用车内预热或危险警示灯约15分钟后。2. [马自达3和CX-30] 使用危险警示灯约15分钟后。3. [马自达3、CX-30和MX-30] 当两个触控传感器同时被触碰时。原因1(症状1):水可能在外手柄的触摸传感器周围积聚,导致电容传感器灵敏度暂时降低。此外,如果洗车泡沫进入外手柄,可能会干扰触摸传感器检测。马自达仍在针对此问题进行量产改进。原因2(症状2):生产过程中焊接不当可能干扰触摸传感器检测。为消除此问题,已修改生产工艺。有此疑虑的客户应通过以下维修程序进行车辆维修。维修程序1.核实客户关切。2. 根据症状进行车辆维修。症状1:按照以下“防水触摸传感器程序”进行,使触摸传感器防水。症状2:按照MGSS上的说明更换前外手柄,换成改装过的手柄。马自达3(前外手柄拆卸/安装) CX-30(前外手柄拆卸/安装) MX-30(前外手柄拆卸/安装)如果同时出现两种症状:更换改装的前外手柄,并按照程序防水触摸传感器,使触摸传感器防水。注意:如果车辆没有任何问题,不要修理另一侧前外手柄。3. 通过检查新外手柄是否能正确锁闭/解锁车门来验证维修情况。

NHTSA · 制造商通报11030603车型年份 2022自动翻译 · 原文:英语查看详情 →
通报中等电气NA

通报

Some customers may experience the master warning light and/or the "In-Vehicle Network Malfunction" warning message in the instrument cluster on with DTC B119F:01 (TCU - Tel antenna No. 1 malfunction) stored.

NHTSA · 制造商通报11003361车型年份 2022以原文(英语)显示 · 翻译待完成查看详情 →
通报中等制动NA

通报

Some customers may experience the following concerns: The liftgate or the trunk lid will not unlock even when the vehicle is parked and the ignition is off. If the engine is running (POWER ON) or the ignition is turned to on (READY ON), it will unlock. The auto close operation of the power liftgate is not performed (The liftgate can be closed manually). To eliminate this concern, the control software of the DSC HU/CM (or the electronically controlled brake unit) has been modified. Customers

NHTSA · 制造商通报11003356车型年份 2023以原文(英语)显示 · 翻译待完成查看详情 →
通报中等制动NA

通报

Some customers may experience that the liftgate or the trunk lid will not unlock even when the vehicle is parked and the ignition is off. If the engine is running (POWER ON) or the ignition is turned to on (READY ON), it will unlock. To eliminate this concern, the control software of the DSC HU/CM (or the electronically controlled brake unit) has been modified.

NHTSA · 制造商通报10254184车型年份 2023以原文(英语)显示 · 翻译待完成查看详情 →
通报中等车身NA

通报

Some customers may experience that, with a specific operation, the touch sensor of front door outer handle does not lock and unlock the doors but the remote transmitter operates correctly. Description of the specific operations: Specific Operation 1 [MX-30]: After using cabin preconditioning or hazard warning lights for approx.15 minutes. Specific Operation 2 [MAZDA3 and CX-30]: After using hazard warning lights for approx. 15 minutes. Specific Operation 3 [MAZDA3, CX-30 and MX-30]: When both touch sensors are touched at once. Specific Operation 1 and 2 Cause: The touch sensor has been disabled to avoid the unintended locking/unlocking operation caused by rain. Specific Operation 3 Cause: The control logic is not appropriate. NOTE: If the concern occurs without the specific operation above, refer to TSB 09-019/22 (DOOR OUTER HANDLE TOUCH SENSOR DOES NOT LOCK AND/OR UNLOCK). To correct this issue, the control software of the LF control unit (LFU) has been modified.

NHTSA · 制造商通报10252505车型年份 2022以原文(英语)显示 · 翻译待完成查看详情 →
通报中等车身NA

通报

Some customers may complain that oil leaks from the rear shock absorber. Due to the structure, a small amount of oil is leaked out, but there is no functional concern. However, this oil leak level is almost the same where shock absorber replacement is required. To eliminate this concern, the structure of the oil seal in the rear shock absorber has been modified

NHTSA · 制造商通报10244579车型年份 2022以原文(英语)显示 · 翻译待完成查看详情 →
通报中等悬架NA

通报

Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 7000C0A-NA02_11046). Ver. 7000C0A-NA02_11046 fixes these software errors (bugs): The system does not resume the play list after editing a play list for an USB audio device. The screen does not show proper picture when receiving SiriusXM data. Ver. 7000C0A-NA02_11044 fixes these software errors (bugs): Beep sounds every couple of minutes. Language setting may not be accepted correctly. When refusing the incoming call while playing audio tracks using the Apple CarPlay, the screen shows Phone in use message and it stops playing audio tracks. The audio track may not pause when pressing the mute button. The screen freezes when smartphone receives messages under Bluetooth connection. Ver. 7000C0A-NA02_11036 fixes these software errors (bugs): Screen freezes and goes to white screen, then the system reboots. Cannot control the audio system with steering switches and command switch. If another incoming call comes in immediately after the hands-free call is ended, the call is automatically accepted. Establishing Bluetooth connection takes tiime. DTC U3000:49 is stored which may be accompanied with following symptoms. -No sound comes out from the speakers. -Audio source selection is unavailable. The vehicle icon rotates when using the navigation with "head-up" mode.

NHTSA · 制造商通报10238677车型年份 2022以原文(英语)显示 · 翻译待完成查看详情 →
通报中等其他NA

通报

Some customers may complain that Mazda Connect does not start (blank screen) or that it takes a long time to restart/ reboot after starting the vehicle. This is caused by the initialization process with the CMU failing at startup due to a defective circuit board element. To eliminate this concern, the internal hardware (DRAM) of the CMU has been improved.

NHTSA · 制造商通报10237206车型年份 2022以原文(英语)显示 · 翻译待完成查看详情 →
通报中等车身NA

通报

Some customers may complain that oil leaks from the rear shock absorber. Due to the structure, a small amount of oil is leaked out, but there is no functional concern. However, this oil leak level is almost the same where shock absorber replacement is required. To eliminate this concern, the structure of the oil seal in the rear shock absorber has been modified.

NHTSA · 制造商通报10233659车型年份 2022以原文(英语)显示 · 翻译待完成查看详情 →
通报中等其他NA

通报

Some customers may complain that Mazda Connect does not start (blank screen) or that it takes a long time to restart/ reboot after starting the vehicle. This is caused by the initialization process with the CMU failing at startup due to a defective circuit board element. To eliminate this concern, the internal hardware (DRAM) of the CMU has been improved.

NHTSA · 制造商通报10233569车型年份 2022以原文(英语)显示 · 翻译待完成查看详情 →
通报中等悬架NA

通报

Some vehicles may exhibit a steering shimmy or body vibration during the PDI test drive or during the first few miles of driving after the vehicle has been delivered to the customer due to flat spots on the tires. Flat spots on tires may be caused by improper maintenance during dealer storage (e.g.: Vehicle was left stationary for a prolonged period of time in high ambient temperatures).

NHTSA · 制造商通报10232302车型年份 2022以原文(英语)显示 · 翻译待完成查看详情 →
通报中等制动NA

通报

Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.

NHTSA · 制造商通报10230875车型年份 2022以原文(英语)显示 · 翻译待完成查看详情 →
通报中等其他NA

通报

Some customers may complain that Mazda Connect does not start (blank screen) or that it takes a long time to restart/ reboot after starting the vehicle. This is caused by the initialization process with the CMU failing at startup due to a defective circuit board element. To eliminate this concern, the internal hardware (DRAM) of the CMU has been improved.

NHTSA · 制造商通报10226898车型年份 2022以原文(英语)显示 · 翻译待完成查看详情 →
通报中等车身NA

通报

Some customers may experience that, with a specific operation, the touch sensor of front door outer handle does not lock and unlock the doors but the remote transmitter operates correctly. Description of the specific operations: - Specific Operation 1 [MX-30]: After using cabin preconditioning or hazard warning lights for approx.15 minutes. - Specific Operation 2 [MAZDA3 and CX-30]: After using hazard warning lights for approx. 15 minutes. - Specific Operation 3 [MAZDA3, CX-30 and MX-30]: When both touch sensors are touched at once. - Specific Operation 1 and 2 Cause: The touch sensor has been disabled to avoid the unintended locking/unlocking operation caused by rain. - Specific Operation 3 Cause: The control logic is not appropriate. To correct this issue, the control software of the LF control unit (LFU) has been modified.

NHTSA · 制造商通报10226892车型年份 2022以原文(英语)显示 · 翻译待完成查看详情 →
通报中等制动NA

通报

Some customers may complain about the following message displayed in the Multi-Information Display: In the following cases, the MRCC with Stop & Go function system is canceled when the vehicle is traveling at 19 mph (30 km/h) or less: * The Forward Sensing Camera (FSC) cannot detect target objects due to one of the following: - The windshield is dirty - The FSC lens is foggy - There is low visibility due to rain, fog or snow - It is at night and there is not enough light - There is direct or reflected sunlight on the FSC - There is problem with the FSC * There is a problem with the AUTOHOLD control function. * There is a problem with the electric parking brake (EPB).

NHTSA · 制造商通报10225763车型年份 2022以原文(英语)显示 · 翻译待完成查看详情 →
通报中等悬架NA

通报

The Blind Spot Monitoring (BSM) system can malfunction with the following symptoms if the rear side radar sensors are installed facing the wrong direction. - BSM system indicates vehicle on the opposite side. - i-ACTIVSENSE indicator ring will not turn green - Rear Cross Traffic Alert (RCTA) does not work - Rear side radar sensor

NHTSA · 制造商通报10222563车型年份 2023以原文(英语)显示 · 翻译待完成查看详情 →
通报中等其他NA

通报

Some customers may complain that Mazda Connect does not start or that it takes a long time to restart after starting the vehicle. This is caused by the initialization process with the CMU failing at startup due to a defective circuit board element. To eliminate this concern, the internal hardware of the CMU has been improved.

NHTSA · 制造商通报10218768车型年份 2022以原文(英语)显示 · 翻译待完成查看详情 →
通报中等制动NA

通报

This information will give you the necessary knowledge to respond to customers concerns of Smart Brake Support (SBS) unintended braking. By educating the customer on the system operation, it should reduce their anxiety or distrust of the vehicle.

NHTSA · 制造商通报10218772车型年份 2022以原文(英语)显示 · 翻译待完成查看详情 →
通报中等悬架NA

通报

Some vehicles may exhibit a steering shimmy or body vibration during the PDI test drive or during the first few miles of driving after the vehicle has been delivered to the customer due to flat spots on the tires. Flat spots on tires may be caused by improper maintenance during dealer storage (e.g.: Vehicle was left stationary for a prolonged period of time in high ambient temperatures).

NHTSA · 制造商通报10213147车型年份 2022以原文(英语)显示 · 翻译待完成查看详情 →
通报中等悬架NA

通报

Some customers may complain that the steering wheel is off center more than 3 even when driving straight on a flat road.

NHTSA · 制造商通报10210902车型年份 2022以原文(英语)显示 · 翻译待完成查看详情 →
通报中等悬架NA

通报

Some customers may complain about the infotainment system and/or the MyMazda App showing incorrect tire pressures and/or tire pressure missing. This may be caused by: Incorrect calendar entry (month/day/year) after a battery disconnect *Infotainment system software update. *BCM TPMS unlearn during vehicle storage or transport. *Wheel/Tire change

NHTSA · 制造商通报10209755车型年份 2022以原文(英语)显示 · 翻译待完成查看详情 →
通报中等悬架NA

通报

Some customers may report concerns with interior upholstery surface stains particularly on high contact areas (e.g.: steering wheel, door panels, shifter...etc.). This may be caused by skin oils or chemicals such as hand lotions. Use a clean towel damped in leather/vinyl cleaner or mild soap to clean the steering wheel. NOTE: Upholstery maintenance and care information can also be found in the Owner's Manual.

NHTSA · 制造商通报10208554车型年份 2022以原文(英语)显示 · 翻译待完成查看详情 →
通报中等电气NA

通报

Some vehicle may experience the i-ACTIVSENSE/ALH warning lights on and a system error messages may be found in the center display as well. DTC U3000:04 (FSC) is stored in memory DTC U3000:04 (FSC) - Forward sensing camera (FSC) internal malfunction This may be caused by a hardware failure in an internal device of the FSC that results in the malfunction detection. To eliminate this concern, the production process of the FSC has been modified.

NHTSA · 制造商通报10206960车型年份 2022以原文(英语)显示 · 翻译待完成查看详情 →
通报中等制动NA

通报

Unexpected Smart Brake Support (SBS-R) Operation Wile Reversing: Some customers may complain about unexpected collision warning or automatic braking while reversing under certain conditions such as a step or object on the road behind the vehicle. This is caused by the control software of the parking assist unit of the Smart Brake Support (SBS-R) unintentionally detecting under certain conditions. To eliminate this concern, the control software of the parking assist unit has been modified. Customers having this concern should have their vehicle repaired using the following repair procedure.

NHTSA · 制造商通报10206010车型年份 2022以原文(英语)显示 · 翻译待完成查看详情 →
通报轻微电气NA

通报

描述 部分车辆可能在召回完成后仍会在中央显示屏上显示召回通知“重要通知。查看车辆状态监控详情”。注意:一旦马自达日本批准召回活动的保修索赔,召回通知将在次日或更晚通过Connected Services自动移除。如果Connected Services订阅在召回通知仍在生效时被取消,这种情况可能会发生。应采取的措施如果您遇到上述情况,请使用MDARS手动移除中央显示屏召回通知。注意:MDARS只有在MCVV显示无CV合同时才能移除召回通知。

NHTSA · 制造商通报11037008车型年份 2023自动翻译 · 原文:英语查看详情 →
更早 →

来源:NHTSA(美国,公有领域)、加拿大交通部(加拿大开放政府许可)、DVSA(英国,开放政府许可 v3.0)、RappelConso 与欧盟 Safety Gate(法国,开放许可 2.0)、日本国土交通省(公共数据许可1.0)、韩国国土交通部(car.go.kr)。