免费阅读 · 免费账户即可贡献Anticars(2000)的继任者

Mazda MX-5

1989– · 4 各代车型 · 已记录36项缺陷 · 4个市场
各代车型

技术服务通报(TSB)是制造商就已知问题发给经销商的维修说明。它们不是安全召回,但常常能证实某个缺陷。

车型年份
MX-5 (ND) · 2015–
通报严重发动机NA

通报

On some vehicles, a sulfur smell or 'rotten egg' odor may be noticed coming from the exhaust system. The odor is usually noticed after a cold start, fast idle, extended periods of idling and full throttle acceleration. Sulfur smell is not an indication of an engine concern and will not cause reduced driveability or durability of the engine or any of its emission components. The sulfur smell or 'rotten egg' odor is caused by high amounts of sulfur in the gasoline being used in the vehicle. Sulfur is normally eliminated during the refining process, but the EPA regulation of sulfur in gasoline differs from state to state. Vehicles using fuel containing high amounts of sulfur will most likely emit sulfur smell from the exhaust system.When high sulfur fuel is burned, there is a chemical reaction in the catalytic converter causing the sulfur tooxidize. As the vehicle is driven, the oxidizing reaction odor in the converter will decrease with mileage and age.

NHTSA · 制造商通报10153311车型年份 2019以原文(英语)显示 · 翻译待完成查看详情 →
MX-5 (ND) · 2015–
通报中等车身NA

通报

本公告取代了以下之前发布的公告。这些变更以红色标注。09-012/21 12/13/21, 06/10/21 和 2021/04/27 描述 部分客户可能会出现以下所有症状:使用远程发射器按钮无法实现门锁/解锁操作。1. 门锁/解锁操作无法使用门锁/释放触摸传感器。2. 发动机无法通过点火开关启动。3. 发射器自行工作。4. 钥匙电池耗电速度比平时更快。5. 症状 1-3:这可能是由于远程发射器承受过多负载,导致电气端子变形并与电池接触不良。为消除这一问题,远程发射器的结构进行了改造,以减少电气端子的变形。症状4-5:可能因对遥控发射器施加过大负载,导致垫圈周围出现缝隙,水分进入并腐蚀电路板,从而使关键电池比平时更快耗尽。为消除此问题,密封圈安装面的壳壁厚度加厚,并增强元件的粘结强度以防止变形。维修程序如果电池损坏或安装错误,请更换电池和/或正确安装。如果远程省电功能关闭且电池安装良好,请按照MGSS(防盗器系统相关零件编程)说明更换有缺陷的远程发射器。注意:如果其他远程发射器没有问题,不要更换车辆的。

NHTSA · 制造商通报11034436车型年份 2020自动翻译 · 原文:英语查看详情 →
MX-5 (ND) · 2015–
通报中等发动机NA

通报

Some vehicles may exhibit oil leakage from the drive belt auto tensioner and rattling noises from the engine compartment. This may be caused by insufficient sealing at the drive belt auto tensioner damper when the auto tensioner fully operates under both high ambient temperature and high load conditions. To eliminate this concern, the shape of the drive belt auto tensioner damper has been changed.

NHTSA · 制造商通报10238663车型年份 2019以原文(英语)显示 · 翻译待完成查看详情 →
MX-5 (ND) · 2015–
通报中等悬架NA

通报

The Blind Spot Monitoring (BSM) system can malfunction with the following symptoms if the rear side radar sensors are installed facing the wrong direction. - BSM system indicates vehicle on the opposite side. - i-ACTIVSENSE indicator ring will not turn green - Rear Cross Traffic Alert (RCTA) does not work - Rear side radar sensor

NHTSA · 制造商通报10222563车型年份 2023以原文(英语)显示 · 翻译待完成查看详情 →
MX-5 (ND) · 2015–
通报中等制动NA

通报

Some vehicles may experience a lack of power and the check engine light on with DTC P061B:00 stored in PCM memory under one of the following conditions (A or B). - DTC P061B:00 - [PCM] Internal control module torque calculation performance problem. Condition Condition Description A When cranking is interrupted (likely occurs when the brake pedal is released during cranking) B When accelerating from 1300-1600 rpm with wide open throttle Due to an improper control logic of the PCM, the engine torque calculation error detection is too sensitive. To eliminate this concern, the PCM software has been modified.

NHTSA · 制造商通报10218722车型年份 2019以原文(英语)显示 · 翻译待完成查看详情 →
MX-5 (ND) · 2015–
通报中等制动NA

通报

Clunk/Rattle noise from rear brake

NHTSA · 制造商通报10213396车型年份 2016以原文(英语)显示 · 翻译待完成查看详情 →
MX-5 (ND) · 2015–
通报中等车身NA

通报

Some vehicles may experience one of the following 2 symptoms, even though the windshield is clear. Under certain driving conditions, the Forward Sensing Camera (FSC) may detect a dirty windshield (not clear). NOTE FOR CUSTOMER: The FSC may not work properly under the conditions: The windshield is not clear. The FSC lens is not clear. Driving in heavy rain, dense fog or snow, or into the sun. Driving on a road with no or blurred road lane markings. When the windshield becomes foggy in the winter time or other cold weather conditions and LDWS/HBC warning lights turn on, drive with the defroster on for about 10 minutes. This will help clear the foggy windshield at the FSC.

NHTSA · 制造商通报10185957车型年份 2016以原文(英语)显示 · 翻译待完成查看详情 →
MX-5 (ND) · 2015–
通报中等其他NA

通报

Some vehicles may exhibit the inner cloth (A) falling down at the rear end causing a poor appearance and obstructing the view of the back window. This is caused by the J-hook binding holding the inner cloth coming loose during the opening/closing of the convertible top, from vibration during driving or from high ambient temperatures. To correct the problem, two top-protector clips have been additionally installed to both side edges of the J-hook to prevent the J-hook from loosening and separating.

NHTSA · 制造商通报10185955车型年份 2016以原文(英语)显示 · 翻译待完成查看详情 →
MX-5 (ND) · 2015–
通报中等电气NA

通报

Ldws and hbc warning lights on and dtc c1001:92

NHTSA · 制造商通报10186337车型年份 2016以原文(英语)显示 · 翻译待完成查看详情 →
MX-5 (ND) · 2015–
通报中等电气NA

通报

If you experience issues with the current version of ID's such as missing tools or modules not showing after completing a network test, be advised that we are aware of these issues and are working to resolve them. As a counter measure, it is advised that you un-install ids and re-install version 103.00 and "do not update" until further notice.

NHTSA · 制造商通报10185813车型年份 2017以原文(英语)显示 · 翻译待完成查看详情 →
MX-5 (ND) · 2015–
通报中等发动机NA

通报

If an engine assembly is replaced after a catastrophic internal mechanical failure, clean the intake manifold internally before installing a replacement engine assembly. If the intake manifold is not cleaned properly, the replacement engine may fail prematurely. Metallic debris from the old engine (with catastrophic internal mechanical failure) may rest inside the intake manifold. When the new engine assembly is installed, debris in the intake manifold will be ingested into the new engine and cause internal damage.

NHTSA · 制造商通报10165676车型年份 2019以原文(英语)显示 · 翻译待完成查看详情 →
MX-5 (ND) · 2015–
通报中等车身NA

通报

Some customers may complain of a lack of power under heavy load without any warning lights or DTCs. This concern may be due to a loose or detached hood weatherstrip, which can cause a blockage or restriction in the air intake system.

NHTSA · 制造商通报10165350车型年份 2019以原文(英语)显示 · 翻译待完成查看详情 →
MX-5 (ND) · 2015–
通报中等其他NA

通报

Due to a database error discovered with IDS 114.00-114.02 release (which affects Recall 3719F), it will be necessary to uninstall IDS 114 and install IDS 113.00 and 113.06 update. The Recall can be performed after removing IDS 114 and installing IDS 113. This SA will be updated when more information is available.

NHTSA · 制造商通报10163333车型年份 2019以原文(英语)显示 · 翻译待完成查看详情 →
MX-5 (ND) · 2015–
通报中等其他NA

通报

On May 1, 2018, Japan produced vehicles starting using 17 mm hex lug nuts instead of 21 mm on the same size thread. When installing the accessory locking lug nuts, make sure to use the appropriate part number for the vehicle you are working on.

NHTSA · 制造商通报10159199车型年份 2018–2019以原文(英语)显示 · 翻译待完成查看详情 →
MX-5 (ND) · 2015–
通报中等悬架NA

通报

On May 1, 2018, Japan produced vehicles starting using 17 mm hex lug nuts instead of 21 mm on the same size thread. When installing new lug nuts or the accessory Wheel Lock Set, make sure to use the appropriate part number for the vehicle you are working on.

NHTSA · 制造商通报10159196车型年份 2018–2019以原文(英语)显示 · 翻译待完成查看详情 →
MX-5 (ND) · 2015–
通报中等其他NA

通报

在配合新的MRT分销方案,马自达将从2019年3月起向经销商发运新的双用途诊断泄漏检测仪。培训视频将很快发布到MGSS,维修手册中的操作程序也将逐步修订。

NHTSA · 制造商通报10154879车型年份 2019自动翻译 · 原文:英语查看详情 →
MX-5 (ND) · 2015–
通报中等悬架NA

通报

Subject: Mazda Service Program (MSP) 53. 2019 CX-3 & 2018-2019 MX-5 With Direct Tire Pressure Monitoring System (TPMS) Panic Alarm System Activates While Driving. Mazda Motor Corporation has decided to conduct a Mazda Service Program (MSP) on certain 2019 CX-3 vehicles produced from February 27, 2018 through October 12, 2018 and 2018-2019 MX-5 vehicles produced from October 3, 2017 through October 15, 2018. On certain subject vehicles equipped with Direct TPMS (TPMS wheel sensor is directly mounted on each wheel), it is possible that the panic alarm system may activate while driving, and the horn may sound intermittently, and hazard warning lights may flash. The panic alarm concern will stop after cycling the ignition switch off, then on again. No DTCs are stored. Action Required: Beginning today, reprogram the body control module (BCM) to the latest calibration using MMDS for all affected CX-3 and MX-5 vehicles in dealer inventory, and when customers bring their vehicles for maintenance, or other service/warranty work. The subject vehicles must not be delivered to customers until the repair of MSP53 is completed. Please inform the customer that the BCM will be reprogrammed to the latest calibration, free of charge. If a vehicle is sold with an open MSP53 your Step 3 PDI warranty claim will be subject to debit.

NHTSA · 制造商通报10154528车型年份 2018–2019以原文(英语)显示 · 翻译待完成查看详情 →
MX-5 (ND) · 2015–
通报中等悬架NA

通报

On certain subject vehicles, it is possible that the panic alarm system may activate while driving, and the horn may sound intermittently and hazard warning lights may flash. The panic alarm concern will stop after cycling the ignition switch off, then on again. No DTCs are stored. Some TPMS wheel sensor IDs on the concerned vehicle or other vehicles nearby may cause the error in the body control module (BCM). Air pressure data transmitted from the wheel sensors may be recognized by the BCM as if the panic button on the remote transmitter has been pressed.

NHTSA · 制造商通报10154531车型年份 2018–2019以原文(英语)显示 · 翻译待完成查看详情 →
MX-5 (ND) · 2015–
通报中等悬架NA

通报

如果车辆在行驶中出现车身振动或方向盘抖动,且根本原因确定为轮胎平衡问题,请使用 Hunter GSP9700 或同等级平衡机对轮胎重新做动平衡。如果经销商没有 GSP9700 或同等级平衡机,则将车辆外包给其他机构进行维修。要查找经销商附近的 GSP9700 设备位置,请访问 Hunter 网站 www.gsp9700.com,然后点击"Locate a GSP9700 Road Force Balancer"(查找 GSP9700 Road Force 平衡机)。

NHTSA · 制造商通报10154139车型年份 2019自动翻译 · 原文:英语查看详情 →
MX-5 (ND) · 2015–
通报中等制动NA

通报

Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.

NHTSA · 制造商通报10153227车型年份 2019以原文(英语)显示 · 翻译待完成查看详情 →
MX-5 (ND) · 2015–
通报中等内饰NA

通报

This information is provided to help address Passenger Airbag Deactivation (PAD) Indicator illumination concerns during vehicle service.

NHTSA · 制造商通报10153329车型年份 2019以原文(英语)显示 · 翻译待完成查看详情 →
MX-5 (ND) · 2015–
通报中等其他NA

通报

This service bulletin provides information regarding the proper use of the driver's floor mat to avoid anypotential interference with the foot pedals. The following are possible causes of floor mat interference,which can be avoided with proper usage. Floor mat moves forward due to improper installation. Inappropriate floor mat (such as aftermarket, non-factory-equipped, or non-genuine) is used. Floor mat is stacked one on top of another.

NHTSA · 制造商通报10153331车型年份 2019以原文(英语)显示 · 翻译待完成查看详情 →
MX-5 (ND) · 2015–
通报中等悬架NA

通报

As of May 1, 2018, Japan produced vehicles use 17 mm hex lug nuts instead of 21 mm on the same size thread. When installing new lug nuts or the accessory Wheel Lock Set, make sure to use the appropriate part number for the vehicle you are working on. NOTE: The Mazda3 produced in Mexico is not affected.Use the GEPC or the Mazda Accessory web site [MXConnect (dealers.mazdausa.com)] to look up the correct part number for the vehicle you are working on.

NHTSA · 制造商通报10153226车型年份 2018–2019以原文(英语)显示 · 翻译待完成查看详情 →
MX-5 (ND) · 2015–
通报中等电气NA

通报

Some vehicles may experience the CHECK ENGINE LIGHT ON with DTC P2610 and P2507 stored inmemory after engine start and room fuse 15A (A) removed. P2610:00: Instrument cluster internal engine off timer performance problem P2507:00: PCM battery voltage low input As a past malfunction, the customer will not notice it (no warning light illuminated), but the DTC may be found during a vehicle service. P2507 in this situation is only applicable on 2016 and later models. This is caused by the engine being started 3 or more times after a short duration of engine off (less than 15 seconds) with the room fused removed. NOTE: The odometer will display "F0-002" during transport mode (room fuse 15A removed). Transport mode is canceled when room fuse 15A is installed or the vehicle odometer is more than 12.4mi (20km). Vehicles in dealer inventory with this concern should be repaired using the following repair procedure.

NHTSA · 制造商通报10153310车型年份 2019以原文(英语)显示 · 翻译待完成查看详情 →
MX-5 (ND) · 2015–
通报中等悬架NA

通报

The vehicles listed above are equipped with a push button start/stop ignition system. Unlike previous Mazda models, there is no key cylinder on the steering column. Therefore, the engine cannot be started with the auxiliary key if the room fuse is removed or if the transmitter battery is dead.

NHTSA · 制造商通报10153313车型年份 2019以原文(英语)显示 · 翻译待完成查看详情 →
更早 →

来源:NHTSA(美国,公有领域)、加拿大交通部(加拿大开放政府许可)、DVSA(英国,开放政府许可 v3.0)、RappelConso 与欧盟 Safety Gate(法国,开放许可 2.0)、日本国土交通省(公共数据许可1.0)、韩国国土交通部(car.go.kr)。