Unable To Install The Left-Hand Power Take-Off (PTO) Unit Upfitters or technicians may experience the following: Unable to install the left-hand PTO unit because of an interference with the fuel line engine bundle. This bulletin involves replacing the fuel line bundle or possibly giving the fuel line bundle to a third party upfitter
NHTSA · نشرة المصنع11025710سنوات الطراز 2025معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Engine Block Heater Cord Not Fully Installed From The Factory. Discussion: During Pre-Delivery Inspection (PDI) you will notice that the engine block heater cord is not installed on the engine block.
NHTSA · نشرة المصنع11018601سنوات الطراز 2025معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Valve Cover Gasket It is advised to replace the full valve cover assembly if you are experiencing a valve cover leak Engineering has updated the skirt height of the valve cover to address oil leaks. Replace the valve cover (part # 04893800AI (right side) or 04893799AH (left side)includes valve cover gasket) to ensure proper repair. Please call FCA Redacted Content to facilitate fast track shipment of failed part.
NHTSA · نشرة المصنع10221366سنوات الطراز 2021معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
GASKET, Timing Case Cover, Rear Gear Housing For 2021 Model Year only. If you are replacing the timing gear housing gasket due to an oil leak, please be sure to also replace all outer timing gear housing bolts (PN# 04638665 and 04882109). Do not discard these bolts as engineering will be requesting them to be returned for analysis.
NHTSA · نشرة المصنع10221373سنوات الطراز 2021معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Valve Cover Gasket If you are experiencing a right valve cover leak and plan on replacing only the gasket, the customer may later return for an oil leak. Engineering has updated the skirt height of the valve cover to address oil leaks. Replace the valve cover (part # 04893800AI includes valve cover gasket) to ensure proper repair. Please call FCA Redacted Content if further questions or help is needed with parts retention returns on valve cover assemblies
NHTSA · نشرة المصنع10214518سنوات الطراز 2021معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Intermittent No Crank No Start This bulletin involves inspecting the ground wire to engine block fastener and replacingif necessary. The customer may comment on the following:A no start and/or intermittent no start condition.
NHTSA · نشرة المصنع10175549سنوات الطراز 2020معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Intermittent No Crank No Start This bulletin involves inspecting the ground wire to engine block fastener and replacingif necessary. The customer may comment on the following:A no start and/or intermittent no start condition.
NHTSA · نشرة المصنع10175136سنوات الطراز 2020معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Intermittent No Crank No Start This bulletin involves inspecting the ground wire to engine block fastener and replacingif necessary. The customer may comment on the following:A no start and/or intermittent no start condition.
NHTSA · نشرة المصنع10174216سنوات الطراز 2020معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
**وصف القطعة:** 5.7 لتر Long Block
**وصف المشكلة:** تركيب الـ 5.7 لتر Long Block Assembly متوافق مع تطبيقات EGR وغير EGR. يجب طلب لوحة الإغلاق لنظام EGR (EGR Block-Off Plate) رقم 53032739AA عند تركيب هذا الـ Long Block Assembly في تطبيق غير EGR، ما لم تكن لوحة الإغلاق لنظام EGR منقولة من المحرك القديم.
Rear Crank Shaft Oil Seal and Retainer Plate For Cummins equipped vehicles only;~ If you are working on a 2016 vehicle ONLY and are replacing the Rear Main Seal for oil leak, replace seal, retainer and gasket using PNs; 05086755A$, 05086754A$, 05015705A$. Remove the retainer with the seal installed. Please do not disturb seal in retainer when removing from engine. Please refer to detailed repair instructions in DealerConnect TechConnect for oil seal retainer replacement.~ Cummins Engineering is currently investigating the root cause of the oil leak concern and would like to analyze these parts. Please contact Chad Eichbrecht at cell (248) 309-2695 to arrange for part return~ If you do not receive a response within 15 minutes, please proceed with normal repair. ~
NHTSA · نشرة المصنع10228156سنوات الطراز 2016معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Customer Satisfaction Notification T12 VECI Label The Vehicle Emission Control Information (VECI) label on about 120,000 of the above vehicles may be missing emission control information. The VECI label is often used during in-use Inspection and Maintenance (I/M) testing to verify proper emissions related components. Incorrect VECI label information could result in denial of vehicle registration for the vehicle in the state of California. A new VECI label must be installed.
NHTSA · نشرة المصنع10224875سنوات الطراز 2015معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Cummins Service Engine Replacement This bulletin involves replacing the engine assembly. Remanufactured long block or short block was installed during a prior repair. A new replacement engine will be installed.
NHTSA · نشرة المصنع10224642سنوات الطراز 2012معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Service - Four Piece Oil Pan Gasket All Cummins Equipped Vehicles ONLY - The replacement oil pan gasket can be a four piece gasket rather than a single piece gasket. This applies to Cummins 5.9L and 6.7L engines only. Installation: 1. Clean the oil pan T-joints.~ 2. Fill the T-joint between the pan rail/gear housing and pan rail/rear seal retainer with sealant. Use Mopar Silicone Rubber Adhesive Sealant or equivalent. 3. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the oil pan flange.~ 4. The four piece gasket will need to be assembled to make a complete oil pan gasket. 5. Lay the oil pan gasket(s) onto the oil pan flange.~ 6. Ensure the oil pan gasket segment joints are properly aligned. 7. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the top of the oil pan gasket.~ 8. Install the oil pan. Starting from the center and working outward, tighten the oil pan bolts to 28 Nm [21 ft. lbs.].
NHTSA · نشرة المصنع10223854سنوات الطراز 1998معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Replace Vehicle Emission Certification Information Label This bulletin involves replacing the Vehicle Emission Certification Information (VECI) Label.Owner may be turned away from Inspection and Maintenance (IM) station or fail IM testing because of missing emission components on VECI label. The customer may notice that some info is missing on their VECI labels.is missing. If information is shown in this area, do not replace the label.All vehicles were built with the correct emission components installed and there is no impact on emission performance or drivability.
NHTSA · نشرة المصنع10223853سنوات الطراز 2015معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
**وصف القطعة:** كتلة المحرك الطويلة 5.7L
**وصف المشكلة:** تجميعة الكتلة الطويلة 5.7L هذه متوافقة مع تطبيقات EGR وتطبيقات Non-EGR. يجب طلب لوحة سد EGR (53032739AA) عند تركيب تجميعة الكتلة الطويلة هذه في تطبيق Non-EGR، إلا إذا كانت لوحة سد EGR منقولة من المحرك القديم.
Rear Crank Shaft Oil Seal and Retainer Plate For Cummins equipped vehicles only;~ If you are working on a 2016 vehicle ONLY and are replacing the Rear Main Seal for oil leak, replace seal, retainer and gasket using PNs; 05086755A$, 05086754A$, 05015705A$. Remove the retainer with the seal installed. Please do not disturb seal in retainer when removing from engine. Please refer to detailed repair instructions in DealerConnect TechConnect for oil seal retainer replacement.~ Cummins Engineering is currently investigating the root cause of the oil leak concern and would like to analyze these parts. Please contact Chad Eichbrecht at cell (248) 309-2695 to arrange for part return~ If you do not receive a response within 15 minutes, please proceed with normal repair. ~
NHTSA · نشرة المصنع10220272سنوات الطراز 2016معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Oil Pan 2012-2017 Cummins engines with oil pan leaks, please inspect the shallow area of the oil pan for cracks. If cracks are found, please replace as necessary. Cracks are typically found above the cross member area. Please contact Chad Eichbrecht at cell (248) 309-2695 to arrange for part return or email chad.w.eichbrecht@fcagroup.com If you do not receive a response within 15 minutes, please proceed with normal repair.
NHTSA · نشرة المصنع10219836سنوات الطراز 2012معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Diesel Exhaust Fluid (DEF) Injector Inspection This bulletin involves pressurizing the Diesel Exhaust Fluid (DEF) injector line to check for a leak during New Vehicle Preparation. The DEF system may not become functional until the vehicle has been driven for 20 miles at one time. This Bulletin will give the steps necessary to ensure DEF system is not leaking. A very small number of vehicles may experience a DEF fluid leak under the vehicle. Upon further investigation the Technician may find that the DEF injector is broke.
NHTSA · نشرة المصنع10218793سنوات الطراز 2014معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Diesel Exhaust Fluid (DEF) Injector Inspection This bulletin involves pressurizing the Diesel Exhaust Fluid (DEF) injector line to check for a leak during New Vehicle Preparation. The DEF system may not become functional until the vehicle has been driven for 20 miles at one time. This Bulletin will give the steps necessary to ensure DEF system is not leaking. A very small number of vehicles may experience a DEF fluid leak under the vehicle. Upon further investigation the Technician may find that the DEF injector is broke.
NHTSA · نشرة المصنع10217952سنوات الطراز 2014معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Fluid Leak From Washer Reservoir (X44 Warranty Extension 5 Years/100,000 Miles (160,000 KMS)) This bulletin involves inspecting and/or replacing the washer reservoir. A customer may have a condition where fluid is leaking from the washer reservoir. On further inspection the technician may find cracks in the reservoir by the washer pump pocket.
NHTSA · نشرة المصنع10216415سنوات الطراز 2011معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
Some of the above vehicles equipped with a 6.7L diesel engine may experience a condition where the Noise, Vibration, and Harshness (NVH) engine cover insulates the area on the passenger side of the engine. This could cause engine components under the NVH cover to overheat and possibly ignite.
NHTSA · نشرة المصنع10215827سنوات الطراز 2013معروض باللغة الأصلية (الإنجليزية) · الترجمة قيد الانتظارعرض التفاصيل →
المصادر: NHTSA (الولايات المتحدة، ملك عام)، وزارة النقل الكندية (رخصة الحكومة المفتوحة – كندا)، DVSA (المملكة المتحدة، رخصة الحكومة المفتوحة 3.0)، RappelConso وSafety Gate الأوروبي (فرنسا، الرخصة المفتوحة 2.0)، ووزارة MLIT اليابانية (رخصة البيانات العامة 1.0)، ووزارة MOLIT الكورية (car.go.kr).