Bulletin
Bmw: See document search button for owner letter. On certain model year 2008-2011 vehicles, a defect involving the electric auxiliary water pump can over heat or fail to cool engine and fire may occur in vehicle or engine compartment. *pe
🔔 Kostenloses Konto anlegen und Benachrichtigungen zu BMW 7er E65 erhalten
Technische Bulletins (TSB) sind Reparaturanweisungen, die Hersteller ihren Händlern zu bekannten Problemen schicken. Sie sind keine Sicherheitsrückrufe, bestätigen aber oft einen Mangel.
Bmw: See document search button for owner letter. On certain model year 2008-2011 vehicles, a defect involving the electric auxiliary water pump can over heat or fail to cool engine and fire may occur in vehicle or engine compartment. *pe
BMW Parts Bulletin TEC1T RDC Module Return BMW NA has requested the inspection of the following part numbers: 36 10 6 856 227 and 36 10 6 798 872 Stock should not be sold or installed on any vehicle. Please return the part(s) to your facing Regional Distribution Center (RDC). Submit for return using a YR26 damage claim with order reason BM2. A valid BMW delivery and delivery item number must be entered, and TEC1T must appear in the text of your TEC claim. TEC1T is valid from May 30, 2013, through June 13, 2013.The deadline for filing a claim under TEC1T is June 13, 2013. All parts must be returned to your facing RDC no later than June 27, 2013. Part number 36 10 6 856 227: All parts with an index of 02 and older must be returned. All parts with an index of 03 are correct. Part number 36 10 6 798 872: All parts with an index of 03 and older must be returned. All parts with an index of 04 are correct. The Index is the two digit code under the bar code located on the box label. The Index can also be found on the part itself just after the part number. Please re-order the same part number as needed. (c) 2013, BMW of North America, LLC. The contents of this document are confidential and should not be shared with third parties for distribution.
CLOSED-CIRCUIT CURRENT MONITORING. Increased closed-circuit currents may occur permanently or intermittently and cause the battery to discharge prematurely. The increase in closed-circuit current may be caused by a faulty control module or by the installation of a non-approved accessory. In a situation where a vehicle has broken down due to a discharged battery, for diagnostic purposes it is important not to disconnect the battery. This is because a control module will be reset if the battery is disconnected. Following a reset, the faulty control module may start functioning correctly again, making accurate diagnosis impossible. To correctly measure closed-circuit current, the 50-amp or 100-amp clip-on probe can be used in conjunction with the IMIB (Integrated Measurement Interface Box) to properly diagnose closed-circuit current problems over an extended period of time.
2013 MINI JCW Paddle Shifter Retrofit. SZL to EGS harness installation. For necessary preliminary tasks, refer to ISTA and perform the following steps listed in this document.
N63: Proper Ignition Harness Installation and Ground Connections. INFORMATION https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/16511.1.B12241... 10/14/2014 Page 2 of 2 Any consecutive damage to the BSD interface components (DME, alternator voltage regulator, QLT sensor) caused by incorrect reinstallation of the ignition harness is not covered under the BMW New Vehicle /SAV Limited Warranty.
Battery Maintenance Requirements: Battery Care. Proper battery maintenance is vital when BMW vehicles are in your center's inventory. Allowing a vehicle's battery voltage to drop below 12.0 volts (12.0V) permanently reduces the battery life expectancy and can lead to premature failure of the battery. For vehicles, equipped with a high-voltage battery (hybrid/electric vehicles), failure to properly maintain this battery may lead to a greatly discharged HV battery, requiring replacement. We provide a flexible battery maintenance system every BMW center can use in accordance with their particular needs. This bulletin explains the Battery Charging Calendar (see attachment), charging systems and a simplified tool and battery voltage checking procedure below.
BMW Parts Bulletin TEC9V Fuel Tank / Level Sensor Returns BMW AG has requested an inspection of the following part numbers: 16 11 7 268 031, 16 11 7 268 032 and 16 11 7 297 340 Stock should not be sold or installed on any vehicle. 16 11 7 268 031 and 16 11 7 268 032 All fuel tanks produced before 05/30/2014 needs to be returned. All parts with later dates of production are ok and can be used. 16 11 7 297 340 All level sensors produced in Poland before 05/19/2014 (date is shown as day 139 of year 14 on the part) need to be returned. Those produced after this date are ok and can be used. All level sensors produced in Brazil currently in dealer inventory need to be returned. Please return all part(s) to your facing Regional Distribution Center (RDC). Submit for return using a YR26 damage claim with order reason BM2. A valid BMW delivery and delivery item number must be entered, and TEC9V must appear in the text of your TEC claim. TEC9V is valid from September 24, 2014, through October 08, 2014. The deadline for filing a claim under TEC9V is October 08, 2014. All parts must be returned to your facing RDC no later than October 22, 2014. Please re-order the same part numbers as needed. (c) 2014, BMW of North America, LLC. The contents of this document are confidential and should not be shared with third parties for distribution. Page 2 / 2 Made in Poland Made in Brazil Need to be returned (c) 2014, BMW of North America, LLC. The contents of this document are confidential and should not be shared with third parties for distribution.
BMW Parts Bulletin TEC3W Leak Diagnosis Module Return BMW AG has requested a return of the following part numbers: 16 13 7 315 813 and 16 13 7 274 147 Stock should not be sold or installed on any vehicle. Leak Diagnosis Module part number 16 13 7 315 813 must be returned. Please reorder new part number 16 13 7 333 302 as needed. Pressure Switch, Leak Diagnosis Module part number 16 13 7 274 147 must also be returned. Please reorder new part number 16 13 7 333 301 as needed. Please return all part(s) to your facing Regional Distribution Center (RDC). Submit for return using a YR26 damage claim with order reason BM2. A valid BMW delivery and delivery item number must be entered, and TEC3W must appear in the text of your TEC claim. TEC3W is valid from September 04, 2014, through September 18, 2014. The deadline for filing a claim under TEC3W is September 18, 2014. All parts must be returned to your facing RDC no later than October 02, 2014.
BMW Parts Bulletin TEC1U RDC Module Return BMW AG has requested an inspection of the following part numbers: 36 10 6 798 872 and 36 10 6 856 227 Stock should not be sold or installed on any vehicle. All parts with a date of and from 26/07/13 (July 26, 2013) are good. All parts with a date prior to 26/7/13 (July 26, 2013) must be returned to your facing Regional Distribution Center (RDC). Submit for return using a YR26 damage claim with order reason BM2. A valid BMW delivery and delivery item number must be entered, and TEC1U must appear in the text of your TEC claim. TEC1U is valid from March 5, 2014, through March 19, 2014.The deadline for filing a claim under TEC1U is March 19, 2014. All parts must be returned to your facing RDC no later than April 2, 2014. Please re-order the same part number as needed. (c) 2014, BMW of North America, LLC. The contents of this document are confidential and should not be shared with third parties for distribution.
TEC9T Return, Battery AGM. BMW AG has requested an inspection and return of affected batteries with the following part number: 61 21 8 520 153: Battery AGM Please inspect your stock of this battery. Batteries with finish code label E3, F3, G3, H3, I3, J3 and K3 should not be sold or installed on any motorcycle and must be held for scrapping by your ACM or FSE.
Closed-circuit Current Measurement. Increased closed-circuit currents may occur permanently or intermittently, and may cause the battery to discharge prematurely. The increase in closed-circuit current may be caused by a faulty control unit, or by the installation of a non-approved accessory. In a situation where a vehicle has broken down due to a discharged battery, for diagnostic purposes it is important not to disconnect the battery. This is because a control unit will be reset if the battery is disconnected. Following a reset, the faulty control unit may start functioning correctly again, making accurate diagnosis impossible. To correctly measure closed-circuit current, the 50-amp clip-on probe (previously used with the IMIB) or the 100-amp clip-on probe can now be used in conjunction with the IMIB (Integrated Measurement Interface Box) to properly diagnose closed-circuit current problems over an extended period of time. Connect the amp clip-on probe directly to the IMIB Measurement input 3 (green socket).
?Delivery Stop ? Natural Vacuum Leak Detection Temperature Sensor. A Delivery Stop has been issued on 6 Series Gran Coupe (F06), 5 Series Sedan (F10), 6 Series Convertible (F12), 6 Series Coupe (F13), and 7 Series (G12) vehicles produced from November 3, 2015 to November 5, 2015. These vehicles may have the incorrect Natural Vacuum Leak Detection (NVLD) temperature sensor installed. Please reference SI B16 09 15 (attached) for additional information. Please be reminded that it is a violation of Federal law for you to sell, lease or deliver any vehicle covered by this notification until the delivery stop repair has been performed. This means that centers may not legally deliver new motor vehicles to a consumer until it is fixed or use/sell replacement equipment/parts subject to a delivery stop. Note also that substantial civil penalties apply to violations of this law. Also, you should not sell, lease or deliver any Certified Pre-Owned or used vehicles subject to a delivery stop until the repair is completed.
losed-circuit Current Measurement. Closed circuit current needs to be measured. Excessive closed-circuit currents may occur continuously or intermittently, and may cause the battery to discharge prematurely. CAUSE The increase in closed-circuit current may be caused by a faulty control unit, or by the installation of a non-approved accessory. INFORMATION In a situation where a vehicle has broken down due to a discharged battery, for diagnostic purposes it is important to not disconnect the battery. This is because a control unit will be reset if the battery is disconnected. Following a reset, the faulty control unit may start functioning correctly again, making accurate diagnosis impossible. To correctly measure closed-circuit current, the 50-amp clip-on probe (previously used with the IMIB) or the 100-amp clip-on probe can now be used in conjunction with the IMIB (Integrated Measurement Interface Box) to properly diagnose closed-circuit current problems over an extended period of time. Connect the amp clip-on probe directly to the IMIB Measurement input 3 (green socket).
Battery Maintenance Requirements: Battery Care. Proper battery maintenance is vital when BMW vehicles are in your center's inventory. Allowing a vehicle's battery voltage to drop below 12.0 volts (12.0V) permanently reduces the battery life expectancy and can lead to premature failure of the battery. For vehicles, equipped with a highvoltage battery (hybrid/electric vehicles), failure to properly maintain this battery may lead to a greatly discharged HV battery, requiring replacement. We provide a flexible battery maintenance system every BMW center can use to meet their particular needs. This bulletin explains the Battery Charging Calendar (see attachment), charging system categories and a simplified tool and battery voltage checking procedure below. INFORMATION To transition the reimbursement of the battery maintenance step from the QCI to the new Battery Care Program described in the procedure section, a reduction in the QCI time allowances was necessary. For more information on the updated QCI payment and the related claim submission information, please refer to SI B01 01 08. Your center will received a separate payment for properly maintaining batteries on in-stock vehicles.
The Engine Intermittently Loses Power. Intermittently the engine may experience a loss of power along with a Drivetrain Malfunction message. The Service Engine Soon light (MIL) may also be illuminated. There are one or more of the following air mass plausibility and Valvetronic system faults stored in the DME memory: E-series with BN2000 ? 2775 - Air mass, plausibility: Air mass too low ? 2C57 - Charging pressure control, plausibility: Pressure too low ? 2DCE - Valvetronic system: No adjustment possible F-series with BN2020 ? 102002 - Air mass, plausibility: Air mass too low ? 120308 - Charging pressure control, plausibility: Pressure too low ? 133B04 - Valvetronic system: No adjustment possible CAUSE ? Defective Valvetronic component ? Erroneous faults set due to DME software parameters
"ISPI NEXT ISTA 3.44 introduces a new concept for displaying repair instructions. The new repair instructions have the following advantages compared to the old style: z All instructions (preliminary and follow-up) needed for the repair are included; hyperlinks are no longer needed. z All special tools needed for the repair can be viewed or printed from one tab in ISTA without leaving the repair instructions page. z All technical data and torque specs for the repair can be viewed from one tab in ISTA without leaving the repair instructions page. The most commonly used instructions have been converted to this new format (including repair instructions for the N63 Customer Care Package), and are listed below. Use these instructions instead of the old format. They will save you time and ensure a better quality repair. The Premium instructions can be found in ISTA with a text search for ""Premium."" 1. 1131052 - Replace both timing chains\PREMIUM (N63) 2. 1166000 - Remove and install or replacing vacuum pump\PREMIUM (N63) 3. 1362561 - Removing and installing or replacing both air-mass meters\PREMIUM (N63) 4. 1371190 - Removing and installing/replacing left clean air pipe\PREMIUM (N63) 5. 1371195 - Removing and installing/replacing right clean air pipe\PREMIUM (N63) 6. 1165025 - Removing and installing/replacing right exhaust turbocharger, right\PREMIUM (N63) 7. 1165030 - Removing and installing/replacing left exhaust turbocharger\PREMIUM (N63) 8. 1115001 - Replacing all engine ventilation lines and connection lines\PREMIUM (N63) 9. 1353332 - Replacing fuel feed line\PREMIUM (N63) 10. 1353315 - Removing and installing or replacing all injectors in the fuel injection system\PREMIUM (N63) 11. 5116165 - E70 Completely remove and install the centre console\PREMIUM 12. 6451591 - E90 Removing and installing/renewing evaporator\PREMIUM 13. 1136046 - E90 Removing and installing or replacing intake and exhaust camshaft adjusters\PREMIUM (N55) 14. 1112100 - E90 Removing and install
BMW Parts Bulletin TEC6X Footwell Module Return BMW AG has requested an inspection of the following part number: 61 35 9 342 897 Stock should not be sold or installed on any vehicle. Concerned are all parts delivered and shipped so far, without a green marker point. All parts with a green marker point are correct and ok to use. (See Image below) Please return all part(s) to your facing Regional Distribution Center (RDC). Submit for return using a YR26 damage claim with order reason BM2. A valid BMW delivery and delivery item number must be entered, and TEC6X must appear in the text of your TEC claim. TEC6X is valid from February 03, 2015 through February 17, 2015. The deadline for filing a claim under TEC6X is February 17, 2015. All parts must be returned to your facing RDC no later than March 03, 2015. Please re-order the same part numbers as needed.
BMW Parts Bulletin TEC8X S-Box with Wiring Harness Return BMW NA has requested the return of the following part numbers: 61 27 8 634 209 Stock should not be sold or installed on any vehicle. Concerned are all parts delivered and shipped so far, which are not marked with a black and green dot. All parts marked with a black and green dot are correct and ok to use. Please return all part(s) to your facing Regional Distribution Center (RDC). Submit for return using a YR26 damage claim with order reason BM2. A valid BMW delivery and delivery item number must be entered, and TEC8X must appear in the text of your TEC claim. TEC8X is valid from February 13, 2015, through February 27, 2015. The deadline for filing a claim under TEC8X is February 27, 2015. All parts must be returned to your facing RDC no later than March 13, 2015. Please re-order the same number if needed.
Bmw: Procedural information on the installation of fuel system low pressure sensor and not correctly installed will lead to failure of low pressure sensor and metal supply line. Model 2008-14. *pe
Retail delivery stop on 2004 my 8 & 12 cylinder vehicles produced may 2004 through july 2004. Due to a manufacturing error, the engine control module mail fail. This could cause the vehicle to stall unexpectedly or fail to start at all. *tt
Engine will crank but not start. There is no communication with the integrated fuel module (TFE) whendiagnosing with ISTA. The following two fault codes will be stored in the DME: 032B43 - Low fuel pressure system, electric fuel pump: pressure value too low CDA594 - Message (- 0x33E) missing, receiver DME, transmitter TFE
**Komponentenspezifische Verlängerung der beschränkten Garantie.** Für die berechtigten Fahrzeuge verlängert BMW of North America, LLC (BMW NA) die beschränkte Garantie für die oberen und unteren aktiven Luftklappen im Kühlergrill des Fahrzeugs auf 15 Jahre/150.000 Meilen, gerechnet ab dem ursprünglichen Inbetriebnahmedatum des Fahrzeugs. 1. Luftklappensteuerung (Link), aktiv, oben (G12, G30 und G32) 2. Luftklappensteuerung (Antrieb), aktiv, oben 3. Luftklappen, oben (Baugruppe) 4. Luftklappen, unten (Baugruppe) Für berechtigte Fahrzeuge des Modelljahres 2017 BMW 530i (B460), die derzeit im Bundesstaat Kalifornien (CA) oder in einem Bundesstaat zugelassen sind, der die kalifornische PZEV/SULEV-Vorschrift vollständig übernommen hat (CT, ME, MD, MA, NJ, NY, RI und VT), beträgt die standardmäßige emissionsbezogene Garantie für die Kühlergrill-Lüftungsklappen vorne 15 Jahre/150.000 Meilen. Diese komponentenspezifische Verlängerung der beschränkten Garantie gilt für Material- und Verarbeitungsfehler. Für diesen Versicherungsschutz gelten dieselben Anforderungen an die Fahrzeugberechtigung, Einschränkungen und Ausschlüsse wie für die BMW Neuwagen-Garantie für Personenkraftwagen und leichte Nutzfahrzeuge. Möglicherweise leuchtet eine Check-Control-Meldung oder MIL (Malfunction Indicator Lamp, Motorkontrollleuchte) auf, wenn Fehler im Zusammenhang mit den oberen und/oder unteren aktiven Luftklappen gespeichert sind. Mögliche Ursachen sind: - Defekte obere Luftklappenverbindung (Link) (G12, G30, G32) - Defekter Stellantrieb der oberen Luftklappe (G01, G02, G12, G30, G32) - Defekte obere Klappenbaugruppe (G01, G02, G12, G30, G32) - Defekte untere Luftklappenbaugruppe (G01, G02, G12, G30, G32) - Softwarefehler im DME, der die obere Klappe beeinflusst (nur G01, G02) Oder: Bei der Sichtprüfung sind die oberen aktiven Luftklappen auf der Beifahrerseite entweder offen oder geschlossen festgesetzt, bewegen sich nicht, und es sind keine Fehler für die aktiven Luftklappen gespeichert (ohne Check-Control-Meldung, Motorkontrollleuchte oder Anzeige).
Check Control-Meldung (CCM) zeigt an: (ID 213): Anhalten, mit besonderer Sorgfalt fahren. Spannungsversorgung Die Leuchte Motorsteuerung bald warten leuchtet mit folgendem DME-Fehlercode: 21B209 - Starter-Generator / Riemen für 48-V-System (OSA_RIEMEN_RISS): Riemen zwischen Verbrennungsmotor und Starter-Generator gerissen. Und/oder es treten zusätzlich eine oder mehrere der folgenden weiteren Probleme auf: Geräusche im Bereich des Riementriebs. Geruch aus dem Motorraum. Rauchentwicklung im Bereich des Riementriebs. Antriebsriemen beschädigt oder vorzeitig verschlissen. Antriebsriemen gerissen.
Eine kleine Anzahl von Rolls-Royce Ghost-Modellen hat möglicherweise nicht das korrekte Drehmoment auf die Lambda-Sensoren, auch als Control- oder Monitor-Sensoren bekannt. Um unsere hohen Qualitäts- und Kundenzufriedenheitsstandards aufrechtzuerhalten, hat Rolls-Royce Motor Cars beschlossen, eine Drehmomentüberprüfung der vorderen und hinteren Lambda-Sensoren an beiden Motorbänken durchzuführen. Dieses Verfahren muss bei den in ISPA oder S-Gate aufgeführten Fahrgestellnummern befolgt werden.
A small number of Rolls-Royce Ghost, Wraith and Dawn vehicles have been identified as having a potential drivability issue affecting the operation and behavior of the engine under a very specific set of circumstances as well as a problem with data transfer when connected to Rolls-Royce Motor Cars workshop equipment. The problem has been rectified with ISTA (Integrated Service Technical application) programming version 4.13.x which contains vehicle software version F001-18-07-545, available to all Rolls-Royce authorized workshops since 24th August 2018.
Quellen: NHTSA (USA, gemeinfrei), Transport Canada (Open Government Licence – Canada), DVSA (Vereinigtes Königreich, Open Government Licence v3.0), RappelConso und EU-Safety-Gate (Frankreich, Licence Ouverte 2.0), MLIT (Japan, Public Data License 1.0) und MOLIT (Südkorea, car.go.kr).