Bulletin
Kein Durchdrehen/kein Start, leere Batterie aufgrund von Ruhestromverbrauch/Entladung.
🔔 Kostenloses Konto anlegen und Benachrichtigungen zu Chevrolet Volt erhalten
Technische Bulletins (TSB) sind Reparaturanweisungen, die Hersteller ihren Händlern zu bekannten Problemen schicken. Sie sind keine Sicherheitsrückrufe, bestätigen aber oft einen Mangel.
Kein Durchdrehen/kein Start, leere Batterie aufgrund von Ruhestromverbrauch/Entladung.
This Preliminary Information communication provides information to the technician about vehicles that may have misfires or rough running on cold start up. Technician may find a Diagnostic Trouble Code P0300. Technician will need to use a scan tool and observe Crankshaft Position Re-sync Counter parameter. The Re-sync Counter parameter should remain at 0 during all operating conditions, and while manipulating the related harnesses and connectors between the crankshaft position sensor and the Engine Control Module. Technician will need to inspect for water intrusion in related connectors, terminals, and components. Tech will need to bring the vehicle up to engine coolant temperature that was stored when Diagnostic Trouble Code P0300 was set. After the engine coolant temperature is up to temperature technician will need to perform compression and cylinder leakage and record the readings. Technician should also verify correct fuel system pressure, inspect the heated oxygen sensors for contamination from fuel, silicon, or the incorrect use of room temperature vulcanization silicone sealant, and inspect the spark plugs for incorrect heat range, coolant or oil fouling, carbon tracking, cracks or insulator fractures at the tip. Technician should also Test for coolant contamination into the cylinders.
This Preliminary Information communication provides information to the technician about vehicles that may have misfires or rough running on cold start up. Technician may find a Diagnostic Trouble Code P0300. Technician will need to use a scan tool and observe Crankshaft Position Re-sync Counter parameter. The Re-sync Counter parameter should remain at 0 during all operating conditions, and while manipulating the related harnesses and connectors between the crankshaft position sensor and the Engine Control Module. Technician will need to inspect for water intrusion in related connectors, terminals, and components. Tech will need to bring the vehicle up to engine coolant temperature that was stored when Diagnostic Trouble Code P0300 was set. After the engine coolant temperature is up to temperature technician will need to perform compression and cylinder leakage and record the readings. Technician should also verify correct fuel system pressure, inspect the heated oxygen sensors for contamination from fuel, silicon, or the incorrect use of room temperature vulcanization silicone sealant, and inspect the spark plugs for incorrect heat range, coolant or oil fouling, carbon tracking, cracks or insulator fractures at the tip. Technician should also Test for coolant contamination into the cylinders.
This Preliminary Information communication provides information to the technician about vehicles that may have misfires or rough running on cold start up. Technician may find a Diagnostic Trouble Code P0300. Technician will need to use a scan tool and observe Crankshaft Position Re-sync Counter parameter. The Re-sync Counter parameter should remain at 0 during all operating conditions, and while manipulating the related harnesses and connectors between the crankshaft position sensor and the Engine Control Module. Technician will need to inspect for water intrusion in related connectors, terminals, and components. Tech will need to bring the vehicle up to engine coolant temperature that was stored when Diagnostic Trouble Code P0300 was set. After the engine coolant temperature is up to temperature technician will need to perform compression and cylinder leakage and record the readings. Technician should also verify correct fuel system pressure, inspect the heated oxygen sensors for contamination from fuel, silicon, or the incorrect use of room temperature vulcanization silicone sealant, and inspect the spark plugs for incorrect heat range, coolant or oil fouling, carbon tracking, cracks or insulator fractures at the tip. Technician should also Test for coolant contamination into the cylinders.
Chevrolet: On certain vehicles, after updated calibrations were installed, may exhibit a possible and an estimated electric range drop. *pe updated 12/7/11. *pe
Service Update for Inventory and Customer Vehicles Connected Navigation Radio Voice Command Not Working Expires with Base Warranty
Service Update for Inventory and Customer Vehicles Connected Navigation Radio Voice Command Not Working Expires with Base Warranty - Eqluipped with Connected Navigation Radio (UHQ)
This technical bulletin provides repair information to correct a customer concern of a Propulsion Power is Reduced message displayed in the DIC and without DTCs set on higher mileage vehicles by reprogramming the HPCM 2.
This Preliminary Information communication advises the technician that some vehicles were not delivered with the Battery Energy Control Module with the latest calibration. Technician may find a Diagnostic Trouble Code P0AA6. Technician will need to update the Battery Energy Control Module with the latest calibrations using Service Programming System.
This preliminary informational bulletin provides information to reprgram the radio to resolve a no XM signal concern due to an internal software condition.
This preliminary information bulletin provides information on reprogramming the radio due to a comment on the radio locking up and becoming inoperative.
this preliminary informational bulletin provides information to reprogram the radio to resolve Voice Recognition, Media Data, Route Guidance, DVD Playback Concerns caused by an internal software concern
This preliminary informational bulletin provides information for Navigation System Inoperative When Using Voice Recognition to Enter Address ? Canada Only
This preliminary bulletin provides a procedure to reprogram the radio to correct the customers concern of Radio Locks Up and/or Resets, Bluetooth Pairing, Voice Recognition and Navigation Updates.
This Preliminary Information communication advises the technician that some vehicles were not delivered with the Battery Energy Control Module with the latest calibration. Technician may find a Diagnostic Trouble Code P0AA6. Technician will need to update the Battery Energy Control Module with the latest calibrations using Service Programming System.
This preliminary informational bulletin provides information for Poor A/C Performance, A/C Blows Warm Air, Different Air Temperature Between Right and Left Instrument Panel Outlets.
This preliminary information bulletin provides a procedure for reprogramming the radio due to not receiving no XM signal.
This preliminary information bulletin provides a procedure for reprogramming the radio to correct the Bluetooth audio from not being heard, XM advisories from not being shown, voice recognition inoperative and the speaker static pop noise.
This preliminary information bulletin provides a procedure for reprogramming the radio due to concerns with voice recognition, media data, guidance and DVD playback.
This preliminary informational bulletin provides information on radio recovery and reprogramming due to the radio locked up and does not respond to user input.
This preliminary informational bulletin provides information on radio reprogramming due to voice recognition, media data, route guidance, DVD playback concerns.
This preliminary information bulletin provides information on SERVICE HIGH VOLTAGE CHARGING SYSTEM message is displayed in the Driver Information Center (DIC) Condition.
This preliminary informational bulletin provides a procedure to reprogram the navigation radio with the latest calibrations to correct a condition of th Navigation system being inopperative when using voice recognition to enter addresses.
This preliminary bulletin provides information on Radio Locks Up and/or Resets, Bluetooth Pairing, Voice Recognition and Navigation Updates.
This preliminary informational bulletin provides a procedure to reprogram the radio for concerns related to Unable to Access MP3 Files on CD, Bluetooth Connectivity, No Audio After a Bluetooth Call, Phone Book Usage Issues
Quellen: NHTSA (USA, gemeinfrei), Transport Canada (Open Government Licence – Canada), DVSA (Vereinigtes Königreich, Open Government Licence v3.0), RappelConso und EU-Safety-Gate (Frankreich, Licence Ouverte 2.0), MLIT (Japan, Public Data License 1.0) und MOLIT (Südkorea, car.go.kr).