Elektrik:Zündung
Der Zündschalter könnte einen internen Kurzschluss erleiden.
🔔 Kostenloses Konto anlegen und Benachrichtigungen zu Ford EXP (alle generationen) erhalten
Der Zündschalter könnte einen internen Kurzschluss erleiden.
Im Zündschalter könnte ein Kurzschluss entstehen, der zu Überhitzung, Rauchentwicklung und möglicherweise zu einem Brand in der Lenksäule des Fahrzeugs führen kann. Dieser Zustand kann sowohl während der Fahrt als auch im unbeaufsichtigten Zustand des Fahrzeugs auftreten. Abhilfe: Der Zündschalter wird durch einen Zündschalter in überarbeiteter Konstruktion ersetzt.
Bei Modellen des Jahrgangs 1984 können sich äußere Risse in den Motorzylinderköpfen bilden, was zu einem Ölaustritt auf den Abgaskrümmer führen kann. Bei Modellen des Jahrgangs 1985 kann die Ventildeckeldichtung des Motors reißen, wodurch Öl auf den Abgaskrümmer gelangen könnte. Beide Zustände bergen die Gefahr, dass sich das Öl entzündet und einen Motorraumbrand verursacht. Korrektur: Bei Modellen des Jahrgangs 1984 werden die Zylinderköpfe überprüft und ersetzt, wenn äußere Risse festgestellt werden. Bei Modellen des Jahrgangs 1985 werden die Ventildeckeldichtungen überprüft und ersetzt, sofern sie nicht einer späteren Bauart entsprechen.
Externe Risse oberhalb des Zylinders Nr. 3 (Modelljahr 1984) oder aufreißende Ventildeckeldichtungen (Modelljahr 1985) könnten dazu führen, dass Öl auf den Abgaskrümmer tropft.
Fahrzeuge können über ein unzureichendes Spiel zwischen den rechten vorderen Bremsleitungen und einer am Motor montierten Halterung verfügen. Unter bestimmten Bedingungen könnte die Halterung die metallene Bremsleitung berühren und zu einem Abrieb an der Leitung führen, was einen Verlust von Bremsflüssigkeit und einen teilweisen Bremsausfall zur Folge haben könnte. Dies würde zu verlängerten Bremswegen führen.
The front sleeve bushings of the cooling fan motors are susceptible to excessive corrosion in areas of high road salt use. This may increase the rotational friction of the fan motor or result in seizure of the armature shaft to the bushing. Either condition may draw current in excess of that of a normally operating motor but less than required to operate the fuse link. This could overheat the motor wiring circuitry and possibly result in an underhood or instrument panel fire. Vehicles affected: Cars not equipped with factory air conditioning. Quebec and atlantic provinces only.
Diese Fahrzeuge entsprechen möglicherweise nicht der C.M.V.S.S. 1103 – Abgasemissionen. Die zentrale Kraftstoffeinspritzung (cfi) kann unter bestimmten Betriebsbedingungen fett laufen. Abhilfe: Es werden verbesserte cfi-Kraftstoffeinspritzdüsen eingebaut und die Leerlaufdrehzahl wird angepasst.
These vehicles do not comply with cmvss 1103 - exhaust emissions. Vehicles affected: 1.6 l engine and atx transmissions
The bolts that attach the d-shaped ring for the shoulder belt are inadequately supported by the material in which they are mounted. The attachment does not comply with the requirements of federal motor vehicle safety standard no. 210, "seat belt assembly anchorages".
The upper torso restraint d-ring which attaches the shoulder belt to the b pillar, under certain test conditions, separated from its anchorage, and may not comply with cmvss 210 - belt anchorage.
These vehicles may not comply with cmvss 1103 - exhaust emissions.
Two door models. Fatigue cracks may occur in the door lock pillars at the front door latch striker reinforcement attachment locations. The fatigue cracks may propogate to the extent that the structural integrity of the door latch striker attachment may be significantly reduced creating the possibility that the door may not be securely retained. This condition is observable by visibly noticeable cracks on the door lock pillar adjacent to the striker assemblies.
Door lock pillars could develop fatigue cracks from normal usage of door, at the point where door latch striker reinforcements are attached.
On the involved vehicles, a thermal limiter in the blower motor resistor circuit of the air conditioner/heater assembly may not function as intended. If the blower motor becomes jammed when the system is operating in the medium-low blower speed, the resistor coils can overheat causing melting and possible ignition.
Vehicles with optional air conditioning. The air conditioner blower motor thermal limiter may not operate as intended when there is a motor blockage or malfunction. Thus, if the blower motor becomes jammed when the system is operating in the medium-low blower speed mode, the resistor coils may overheat causing melting and possible ignition of the polyproplene evaporator housing with associated vehicle damage.
Vehicles equipped with power brakes. Power brake boosters may have bewen improperly assembled by supplier. Mis-indexing of rear shell of some boosters relative to the front shell may have resulted in inadequate crimping of the two shells. If booster were to separate during vehicle operation, complete loss of service brakes would result.
Some vehicles equipped with power brake boosters have front and rear shells that may have been improperly joined. Improperly joined booster shells may separate either partially or completely during brake application.
Vehicle may not meet the fuel spillage requirements of cmvss 301 - fuel system integrity.
Certain vehicles may not meet applicable minimum fuel spillage requirements of federal motor vehicle safety standard no. 301, "fuel system integrity". During a 30 mph rear impact test, fuel spillage limits were exceeded by vehicle.
Quellen: NHTSA (USA, gemeinfrei), Transport Canada (Open Government Licence – Canada), DVSA (Vereinigtes Königreich, Open Government Licence v3.0), RappelConso und EU-Safety-Gate (Frankreich, Licence Ouverte 2.0), MLIT (Japan, Public Data License 1.0) und MOLIT (Südkorea, car.go.kr).