Free to read · free account to contributeSuccessor to Anticars (2000)

Honda Stepwgn

1996– · 6 generations · 21 documented defects · 1 markets
Generations
Model year
MarketAllJP
Stepwgn II (RF3/4/5/6/7/8) · 2001–2005
RecallCriticalEngineJP

燃料タンク

燃料タンクのブリーザホース継ぎ手部(クイックジョイント)の嵌合が不十分なため、クイックジョイントのシール(オーリング)がジョイントパイプと密着していないものがある。そのため、ジョイント嵌合部のシール性が損なわれて燃料満タン時にジョイント嵌合部から燃料が漏れるおそれがある。

MLIT · JapanJul 21, 20051114931Model years 2005Shown in the original Japanese · translation pendingView details →
Stepwgn V · 2015–2022
RecallModerateEngineJP

Fuel pump

During recall work, the low-pressure fuel pump replacement was performed improperly: in some cases, the replacement lock nut was reused, and after the parts were installed, the nut was tightened without using the specified tool. As a result, if the vehicle continues to be used as is, the sealing force may decrease, and gasoline may leak from the pump's mounting area.

MLIT · JapanMay 28, 20261158230Model years 2017–2020Auto-translated · original: JapaneseView details →
Stepwgn V · 2015–2022
RecallModerateEngineJP

Fuel pump

In the impeller (resin impeller) of the low-pressure fuel pump, improper molding conditions can lower the resin density, causing it to swell and deform when exposed to fuel. As a result, the impeller may contact the pump cover, causing the fuel pump to malfunction and, in the worst case, potentially leading to engine stalling while driving.

MLIT · JapanDec 8, 20231154230Model years 2017–2020Auto-translated · original: JapaneseView details →
Stepwgn III (RG) · 2005–2009Stepwgn IV (RK) · 2009–2015
RecallModerateEngineJP

冷却装置

ウォータポンププーリを締結するフランジの端部とプーリ内側曲げ部との距離が短いため、プーリ締結後にフランジがプーリ内側曲げ部に乗り上げ隙間が生じるものがある。そのため、補機ベルト荷重が繰返し加わるとプーリ内側曲げ部が摩耗して締結ボルトが緩み、ボルトが折損して補機ベルトが外れると、発電不良及び冷却不良が発生し、警告灯が点灯するとともにエンジンが停止して再始動できなくなるおそれがある。

MLIT · JapanOct 17, 20131132430Model years 2009–2011Shown in the original Japanese · translation pendingView details →
Stepwgn III (RG) · 2005–2009
RecallModerateEngineJP

冷却装置

原動機の冷却水用ホース両端を固定するラジエータホースバンドの防錆加工時の熱処理方法が不適切なため、当該バンドの締め力が不足しているものがある。そのため、そのままの状態で使用を続けると、ラジエータホースが抜けて冷却水が流出し、最悪の場合、オーバーヒートするおそれがある。

MLIT · JapanMay 16, 20081121180Model years 2008Shown in the original Japanese · translation pendingView details →
Stepwgn I (RF1/2) · 1996–2001
RecallModerateEngineJP

Starting device

The grease applied to the contacts inside the ignition switch has an inappropriate composition. As a result, when the ignition switch is turned off slowly, the arc discharge time at the contacts increases. When the contact temperature rises, the grease hardens, and if this operation is repeated, cuprous oxide forms on the contacts, causing poor electrical continuity at the contact section. Therefore, vibration during driving may cause poor contact continuity, which may stop the engine and make it impossible to restart. In addition, the contacts may overheat locally and the solder on the back side of the contacts may melt. In the worst case, molten solder may fall onto the driver's feet and cause burns.

MLIT · JapanJun 14, 20061116810Model years 1995–1997Auto-translated · original: JapaneseView details →

Sources: NHTSA (United States, public domain), Transport Canada (Open Government Licence – Canada), DVSA (United Kingdom, Open Government Licence v3.0), RappelConso and EU Safety Gate (France, Licence Ouverte 2.0), Japan's MLIT (Public Data License 1.0) and South Korea's MOLIT (car.go.kr).