In the driver-side airbag inflator (gas generator), moisture protection is inadequate, so the gas-generating agent may absorb moisture. Therefore, if the gas-generating agent repeatedly absorbs moisture and dries out during use, the airbag may not deploy normally when it is activated.
In replacement driver-side SRS airbag inflators (inflation devices), the gas-generating agent may deteriorate due to repeated changes in ambient temperature and humidity. As a result, when the airbag deploys, the inflator's internal pressure may rise abnormally, possibly causing the inflator casing to rupture.
For a specific type of driver-side SRS airbag inflator (inflation device), an investigation of market-recovered units found some with large variations in the density of the gas-generating agent. Although the cause has not been determined, there is a possibility that the airbag may not deploy normally when it inflates. Therefore, as a preventive measure, the inflator in question will be replaced with a new one.
The inflators (gas generators) of driver-side SRS airbags were found, among units recovered from the market, to show abnormal internal container pressure output that could lead to abnormal deployment. Although the cause has not yet been determined, as a precautionary measure, inflators of the same type manufactured up to a certain period will be replaced with new units.
On vehicles equipped with a driving assistance device for manually operating the brake pedal, the welds between the brake link plate and shaft, which transmit the operating force, may have insufficient strength. As a result, if the brake arm is pushed further while the vehicle is stopped, excessive force may be applied to the welded portion, causing cracks. If the vehicle continues to be used in this condition, the cracks may grow and, in the worst case, the weld may break, causing the brakes to stop working.
The passenger-side airbag has a welding defect at the joint between the diffuser (gas dispersion unit) inside the inflator (inflation device) and the gas generator body (gas generator). When the airbag is deployed, this joint may separate, causing the diffuser to come loose. As a result, inflation gas cannot be supplied to the airbag, the airbag fails to deploy, and the occupant may suffer excessive injury in a frontal collision.
During recall work, the low-pressure fuel pump replacement was performed improperly: in some cases, the replacement lock nut was reused, and after the parts were installed, the nut was tightened without using the specified tool. As a result, if the vehicle continues to be used as is, the sealing force may decrease, and gasoline may leak from the pump's mounting area.
In the impeller (resin impeller) of the low-pressure fuel pump, improper molding conditions can lower the resin density, causing it to swell and deform when exposed to fuel. As a result, the impeller may contact the pump cover, causing the fuel pump to malfunction and, in the worst case, potentially leading to engine stalling while driving.
In the brake operating simulator of the electric servo brake system, improper manufacturing processes may allow the assembly oil used during production to infiltrate the pressure sensor. As a result, the resistance section inside the sensor may corrode during use, causing abnormal output values. This may illuminate the warning light and activate the fail-safe function, potentially increasing the brake pedal operating force.
In the tailgate open stay, either the mounting structure of the lower ball joint and the body-side ball stud is improper, or the assembly work of the upper ball joint and the body-side ball stud is improper, so the clip that secures the ball joint to the body-side ball stud may float up in some vehicles. If the vehicle continues to be used in this condition, repeated opening and closing of the tailgate may cause the ball joint to come off the body, and the tailgate may suddenly drop.
At the tailgate open stay, the specified fastening seat hole diameter of the tailgate hinge to which the ball stud is mounted, and the specified fastening seat diameter of the ball stud, are inappropriate. As a result, on some vehicles the fastening seat buckles when the tailgate is opened and closed repeatedly. If the vehicle continues to be used in this condition, the ball stud may loosen and, in the worst case, break, causing the tailgate to drop suddenly.
In the brake master cylinder, the secondary cup may deform because its material and shape are inappropriate. The cup swells from the plasticizer that dissolves out of the reservoir tank hose into the brake fluid, and it also deforms when it expands from heat from the engine during driving. As a result, sealing performance drops. If the brake pedal is depressed slowly, brake fluid may leak from the seal area and, in the worst case, braking distance may become longer.
Vehicle Stability Assist (VSA) system: In some units, when the electronic board inside the control unit was soldered to the capacitor, a gap formed at the joint of the capacitor's negative terminal. As electrolytic corrosion gradually causes an oxide film to develop from this gap, electrical noise generated by voltage fluctuations is no longer filtered out. This can cause the sensor that detects the brake pedal depression amount to malfunction, resulting in unintended brake assist activation. In the worst case, the brakes may engage suddenly without the brake lights illuminating.
The grease applied to the contacts inside the ignition switch has an inappropriate composition. As a result, when the ignition switch is turned off slowly, the arc discharge time at the contacts increases. When the contact temperature rises, the grease hardens, and if this operation is repeated, cuprous oxide forms on the contacts, causing poor electrical continuity at the contact section. Therefore, vibration during driving may cause poor contact continuity, which may stop the engine and make it impossible to restart. In addition, the contacts may overheat locally and the solder on the back side of the contacts may melt. In the worst case, molten solder may fall onto the driver's feet and cause burns.
Key interlock mechanism (a mechanism that prevents the key from being removed when the AT selector lever is not in the P position): Due to improper assembly of the key cylinder body, metal particles generated during crimping of the key cylinder body cover can become lodged in the operating section of the interlock lever, slowing the lever's movement in some vehicles. As a result, if the key is removed in a short time while the AT selector lever is not in the P position, the key may come out. If the parking brake has not been applied, the vehicle may start to move while parked.
Sources: NHTSA (United States, public domain), Transport Canada (Open Government Licence – Canada), DVSA (United Kingdom, Open Government Licence v3.0), RappelConso and EU Safety Gate (France, Licence Ouverte 2.0), Japan's MLIT (Public Data License 1.0) and South Korea's MOLIT (car.go.kr).