Lectura libre · cuenta gratuita para colaborarSucesor de Anticars (2000)

BMW Serie 7 E32

1986–1994 · 5 averías documentadas · 4 mercados
Año del modelo
MercadoTodosNA
LlamadaCríticoHabitáculoNA

Airbag

On certain 318I, 318IS, 325I, 325IS, 525I, 525IT, 535I, 735I, 735IL, 750IL, 850I and M5, the locking tab for the airbag contact ring in the steering wheel assembly could break without warning. If this happens it is possible that the contact ring wiring could break. This would cause the readiness indicator lamp ("SRS" or "AIRBAG") to illuminate and in such a case the airbag would not be available for deployment in a frontal impact. Correction: Locking tab will be replaced with one of a different design.

Transport Canada7 oct 19961996159Años modelo 1991–1992Mostrado en inglés original · traducción pendienteVer detalles →
LlamadaCríticoHabitáculoNA

Air bags:Frontal

The air bag contact ring locking tab located in the steering wheel assembly can break without warning.

NHTSA · Estados Unidos1 jul 199696V110000Años modelo 1991–1992Mostrado en inglés original · traducción pendienteVer detalles →
LlamadaCríticoMotorNA

Fuel System

On certain 318I, 318IC, 318IS, 325IC, 325IS, 325IX, 525I, 535I, 735I and 735IL vehicles, the fuel feed hose could harden and "set" over time due to engine compartment temperatures. If this "setting" occurs, it is possible that seepage between the hose and fitting could result because the clamp cannot provide sufficient sealing force to compensate for the hardening of the hose. Fuel seepage, in the presence of an ignition source, could result in an engine compartment fire. Correction: fuel feed hoses and associated clamps will be replaced with ones of a new design.

Transport Canada30 may 19941994096Años modelo 1989–1993Mostrado en inglés original · traducción pendienteVer detalles →
LlamadaCríticoMotorNA

Fuel system, gasoline:Delivery:Hoses, lines/piping, and fittings

Feed fuel hoses can harden and "set" over time, allowing a seepage of fuel at the connection between the hose and the engine fitting. The clamp used to hold the hose to the fitting is unable to compensate for the hardening of the feed fuel hose.

NHTSA · Estados Unidos11 abr 199494V066000Años modelo 1989–1993Mostrado en inglés original · traducción pendienteVer detalles →
LlamadaModeradoHabitáculoNA

Calefactor y desempañador

En determinados vehículos, la falla de un componente del sistema de refrigeración, como el termostato, la bomba de agua o la correa del ventilador, puede provocar un aumento significativo de la temperatura del refrigerante y de la presión del sistema. El aumento de presión podría causar la formación de una grieta o la separación de una costura en la pieza terminal del núcleo de la calefacción, lo que provocaría que el refrigerante caliente sea expulsado desde el núcleo de la calefacción. Este fluido caliente podría entrar en contacto con los ocupantes del vehículo, con posibles lesiones personales y/o empañamiento de las superficies interiores de los cristales. Corrección: El tapón del radiador será reemplazado por un tapón de nuevo diseño para evitar la acumulación de presión excesiva en el sistema de refrigeración.

Transport Canada14 oct 19981998197Años modelo 1988–1993Traducido automáticamente · original: inglésVer detalles →
LlamadaModeradoMotorNA

Engine and engine cooling:Cooling system

Vehicle description: Passenger vehicles. A malfunction or failure of a coolant system component, such as a thermostat, water pump, or fan belt, can result in significantly increased coolant temperature and system pressure. If the indications of a critical overheating condition is not noticed by the driver, it is possible that damage to, or failure of, a coolant system component could occur.

NHTSA · Estados Unidos4 ago 199898V178000Años modelo 1988–1993Mostrado en inglés original · traducción pendienteVer detalles →
LlamadaModeradoMotorNA

Motor

En los modelos 318IC, 318IS, 318TI, 325I, 325IC, 325IS, 525I, 525IT, 530I, 530IT, 540I, 740I, 740IL, 840CI y M3 fabricados en algunos casos, el cable del control de crucero y el cable del acelerador están conectados a la misma palanca de accionamiento de la válvula de mariposa, en la carcasa del acelerador. Es posible que el casquillo de plástico de cualquiera de los dos cables se rompa, lo que haría que la funda exterior del cable se separe del casquillo. Si se pisa el pedal del acelerador sin que el control de crucero esté activado, el tubo exterior podría engancharse en el borde del casquillo roto, y la válvula de mariposa podría quedarse parcialmente abierta. Si esto llegara a ocurrir, el vehículo podría no desacelerar como se espera y podría producirse un accidente. Corrección: Se instalará un clip de resorte en el tubo exterior de cada cable para evitar que se desprenda del casquillo.

Transport Canada9 oct 19971997173Años modelo 1993Traducido automáticamente · original: inglésVer detalles →
LlamadaModeradoMotorNA

Control de velocidad del vehículo

Los cables del control de crucero y del acelerador están conectados a la misma palanca de accionamiento de la válvula de mariposa en la carcasa del acelerador. Es posible que el casquillo de plástico de cualquiera de los dos cables se rompa debido a las influencias ambientales combinadas con la vibración. Si el casquillo se rompe, la funda exterior del cable puede separarse del casquillo. En este caso, al pisar el pedal del acelerador sin que el control de crucero esté activado, la funda exterior podría engancharse en el borde del casquillo roto.

NHTSA · Estados Unidos19 ago 199797V131000Años modelo 1993Traducido automáticamente · original: inglésVer detalles →
LlamadaModeradoElectrónicaNA

Lights And Instruments

On certain 325I, 325IC, 325IS, 525I, 525IT, 530I, 530IT, 535I, 540I, 735I, 735IL, 740I, 740IL and 750I, the brake light switch may fail due to a reduction of contact force on the "snap contact" system which the switch incorporates. This could cause heat induced distortion of the plastic internal switch parts in the area of the electrical contacts. This could cause the switch to remain either in the ON or the OFF position resulting in the brake lights being continuously illuminated or inoperative regardless of brake pedal operation. Correction: Switch will be replaced with on that utilizes a different contact system.

Transport Canada7 oct 19961996158Años modelo 1990–1993Mostrado en inglés original · traducción pendienteVer detalles →
LlamadaModeradoFrenosNA

Exterior lighting:Brake lights:Switch

The brake light switch can fail allowing the switch to remain in the "brake lights off" position or in the "brake lights on" position.

NHTSA · Estados Unidos1 jul 199696V111000Años modelo 1990–1993Mostrado en inglés original · traducción pendienteVer detalles →
LlamadaModeradoMotorNA

Engine

On certain 740IA and 740ILA vehicles, the inner throttle cable could break due to a smaller than specification bend in the cable tube. If this were to occur, throttle control would be lost and the engine would return to or remain at idle. Correction: Throttle cable will be replaced with one meeting BMW specifications.

Transport Canada25 abr 19941994081Años modelo 1993Mostrado en inglés original · traducción pendienteVer detalles →
LlamadaModeradoMotorNA

Vehicle speed control:Cables

The throttle cable's tube (outer casing) contains a bend that leads to increased loading of the inner cable, causing it to break.

NHTSA · Estados Unidos3 ene 199494V022000Años modelo 1993Mostrado en inglés original · traducción pendienteVer detalles →
LlamadaModeradoMotorNA

Engine

On certain 535I, 535IA, 735IA, 735ILA vehicles, the nut which secures the throttle valve shaft may not have been tightened with sufficient torque. If the nut were to loosen, it is possible that movement of the throttle valve might be impaired. If this should occur, the vehicle might not decelerate as expected after the gas pedal is released and loos of vehicle control could result. Correction: Vehicles will be inspected and affected throttle housings with undertorqued throttle valve retaining nuts will be replaced.

Transport Canada13 oct 19921992129Años modelo 1991Mostrado en inglés original · traducción pendienteVer detalles →
LlamadaModeradoMotorNA

Vehicle speed control

Some of these vehicles are equipped with a throttle housing on which the throttle valve shaft retaining nut was not sufficiently tightened.

NHTSA · Estados Unidos10 jul 199292V101000Años modelo 1991Mostrado en inglés original · traducción pendienteVer detalles →
LlamadaModeradoHabitáculoNA

Seats And Restraints

On certain 525I, 535I, 735I, 735IL and 750IL vehicles, the front seat center fold-down armrest may contact and damage the seatbelt buckle if the seat back is moved forward to an upright position while the armrest is locked in the down position (horizontal). If this occurs, the release button may be held in the down position, preventing the seatbelt from being latched during the buckle-up operation. Non-latching of the seatbelts will increase the risk of personal injury in the event of a crash. Correction: Front seat safety belt buckles will be replaced with shorter ones that are not susceptible to damage by contact with the armrest.

Transport Canada27 feb 19901990037Años modelo 1988–1990Mostrado en inglés original · traducción pendienteVer detalles →
LlamadaModeradoHabitáculoNA

Seat belts:Front:Buckle assembly

Under certain conditions, front seat center, fold-down arm rest may contact the safety belt buckle, causing damage to the release button and preventing the belt tongue from latching when buckling up.

NHTSA · Estados Unidos30 ene 199090V016000Años modelo 1988–1990Mostrado en inglés original · traducción pendienteVer detalles →
LlamadaModeradoMotorNA

Emissions

Certain 750IL vehicles fail to comply with the requirements of CMVSS 1103 - Exhaust Emissions.

Transport Canada2 may 19891989063Años modelo 1988–1989Mostrado en inglés original · traducción pendienteVer detalles →
LlamadaModeradoMotorNA

Emissions

Certain 750IL vehicles fail to comply with the requirements of CMVSS 1103 - Exhaust Emissions

Transport Canada2 may 19891989062Años modelo 1988–1989Mostrado en inglés original · traducción pendienteVer detalles →
LlamadaModeradoMotorNA

Engine

On certain 750IL vehicles, during the assembly process, the gas pedal may not have been properly attached to the floor pan. If the gas pedal is operated in a rough or erratice manner, it may become stuck between the gas pedal stop (on the floor pan) and the carpeting on the transmission tunnel. If this occurs, the pedal might not return fully to the idle position when the driver's foot is removed and loss of control could result. Application of the brake pedal will close the throttle on this model of vehicle. Correction: Accelerator pedal will be inspected and tightened to the floor is required. Also, a modified pedal stop will be installed.

Transport Canada6 abr 19891989046Años modelo 1988–1989Mostrado en inglés original · traducción pendienteVer detalles →
LlamadaModeradoOtroNA

Vehicle speed control:Accelerator pedal

Accelerator pedals may not have been properly attached to the floor pan during assembly.

NHTSA · Estados Unidos17 ene 198989V005000Años modelo 1988–1989Mostrado en inglés original · traducción pendienteVer detalles →
LlamadaModeradoElectrónicaNA

Electrical

On certain 325E, 325ES, 528E, 535I, 635CSI and 735I vehicles, the center high mounted brake light could add sufficient electrical load to cause the brake light switch to overheat, eventually leading to melting of the plastic internal switch parts. This could cause the switch plunger to jam in the ON or OFF position. This would render the brake light permanently ON or OFF regardless of brake pedal operation. Correction: A brake light switch with an increased current load capacity will be installed on affected vehicles.

Transport Canada27 nov 19861986134Años modelo 1986–1987Mostrado en inglés original · traducción pendienteVer detalles →
LlamadaModeradoFrenosNA

Exterior lighting:Brake lights:Switch

Brake light switch could overheat, eventually leading to melting of plastic internal parts in area of electrical contacts.

NHTSA · Estados Unidos10 nov 198686V151000Años modelo 1986–1987Mostrado en inglés original · traducción pendienteVer detalles →
LlamadaLeveHabitáculoNA

Seats And Restraints

On certain 725I, 735IA and 750IL vehicles, on the front seats, the seatbacks may not have been fully seated on the recliner arms. This could result in looseness of, or noise in the seat. In extreme cases, during a severe rear impact, the seatback may not support the occupant and increase the risk of injury. Correction: Seatbacks will be inspected and properly seated if required.

Transport Canada25 ago 19881988124Años modelo 1988Mostrado en inglés original · traducción pendienteVer detalles →
LlamadaLeveHabitáculoNA

Seats

The driver and/or passenger seatbacks may not have been fully attached to the seat base reclining arms (attaching brackets).

NHTSA · Estados Unidos11 ago 198888V135000Años modelo 1988Mostrado en inglés original · traducción pendienteVer detalles →

Fuentes: NHTSA (Estados Unidos, dominio público), Transport Canada (Licencia de Gobierno Abierto – Canadá), DVSA (Reino Unido, Open Government Licence v3.0), RappelConso y Safety Gate de la UE (Francia, Licence Ouverte 2.0), MLIT (Japón, Licencia de Datos Públicos 1.0) y MOLIT (Corea del Sur, car.go.kr).