Lecture libre · compte gratuit pour contribuerSuccesseur d’Anticars (2000)

Bentley Arnage

1998–2009 · 1 générations · 0 défauts documentés · 2 marchés
Générations
Toutes les générationsArnage1998–20093632

Les bulletins techniques (TSB) sont des instructions de réparation que les constructeurs envoient à leurs concessionnaires sur des problèmes connus. Ce ne sont pas des rappels de sécurité, mais ils confirment souvent un défaut.

Année modèle
MarchéTousNAUK
BulletinModéréCarrosserieNA

Bulletin

## Diagnostic directives : suspicion de fuite de fluide frigorigène du CVC ou signalements d'odeur d'humidité/de moisi dans l'habitacle Diagnostic guidelines. Customer statement / workshop findings: HVAC not cooling / HVAC cooling less than expected / HVAC refrigerant leakage confirmed Or The customer reports a damp/musty smell within the cabin Note : Pour ce scénario, veuillez consulter les prérequis ci-dessous. Si aucune fuite de CVC n'est évidente et qu'une odeur d'humidité/de moisi a été signalée ou constatée, l'opérateur doit d'abord confirmer qu'aucune eau ne pénètre dans l'habitacle ; veuillez vous reporter à toutes les TPI applicables au VIN. Si aucune fuite d'eau n'est évidente, l'opérateur doit vérifier que les évacuations du CVC et de la caisse ne sont pas obstruées. En cas d'obstruction, les évacuations doivent être débouchées. Une fois cette opération terminée, l'opérateur doit confirmer si l'odeur d'humidité/de moisi persiste.

NHTSA · bulletin constructeur10252818Années modèle 2004Traduit automatiquement · original : anglaisVoir le détail →
BulletinModéréFreinsNA

Bulletin

Brake Noise Identification: Customer Statement: -Noise/squeal complaint from the braking system Technical Background: -The noise/squeal can be reproduced and clearly assigned to the braking system

NHTSA · bulletin constructeur10245093Années modèle 2004Affiché en anglais d’origine · traduction en attenteVoir le détail →
BulletinModéréCarrosserieNA

Bulletin

HVAC refrigerant leakage suspected or reports of a damp/musty smell within the cabin - Diagnosis guidelines. Condition HVAC not cooling / HVAC cooling less than expected / HVAC refrigerant leakage confirmed Or The customer reports a damp/musty smell within the cabin. - Should no HVAC leak be evident and a damp/musty smell has been reported/identified the operative should first confirm that water is not leaking into the cabin please refer to all VIN applicable TPIs particularly TPI 2062622/- - Should there be no water leaks evident, the operative should check the HVAC and body drains for blockages, in the event the drains are blocked the drains must be unblocked, once this has been completed the operative should confirm if the damp/musty smell is still evident.

NHTSA · bulletin constructeur10242269Années modèle 2004Affiché en anglais d’origine · traduction en attenteVoir le détail →
BulletinModéréCarrosserieNA

Bulletin

HVAC refrigerant leakage suspected Or reports of a damp/musty smell within the cabin - Diagnosis guidelines. Customer statement / workshop findings: HVAC not cooling / HVAC cooling less than expected / HVAC refrigerant leakage confirmed Or The customer reports a damp/musty smell within the cabin Note: For this scenario please see the pre requisites below - Should no HVAC leak be evident and a damp/musty smell has been reported/identified the operative should first confirm that water is not leaking into the cabin please refer to all VIN applicable TPIs particularly TPI 2062622/- - Should there be no water leaks evident, the operative should check the HVAC and body drains for blockages, in the event the drains are blocked the drains must be unblocked, once this has been completed the operative should confirm if the damp/musty smell is still evident. In the event that HVAC cleaning products are required, these MUST be sourced locally. Before using the cleaner the operative must inform the customer of the product which will be used, a neutral fragrance cleaner should be used as the customer may not like the smell of the cleaner should a fragranced product be used Please ensure all supporting information is included within the DISS query when requesting permission to clean the HVAC system including clear photographs and/or videos showing the reported issue, should the required information not be supplied the warranty claim could be cancelled.

NHTSA · bulletin constructeur10240565Années modèle 2004Affiché en anglais d’origine · traduction en attenteVoir le détail →
BulletinModéréCarrosserieNA

Bulletin

HVAC refrigerant leakage suspected Or reports of a damp/musty smell within the cabin - Diagnosis guidelines. Customer statement / workshop findings: HVAC not cooling / HVAC cooling less than expected / HVAC refrigerant leakage confirmed Or The customer reports a damp/musty smell within the cabin Note: For this scenario please see the pre requisites below - Should no HVAC leak be evident and a damp/musty smell has been reported/identified the operative should first confirm that water is not leaking into the cabin please refer to all VIN applicable TPIs particularly TPI 2062622/- - Should there be no water leaks evident, the operative should check the HVAC and body drains for blockages, in the event the drains are blocked the drains must be unblocked, once this has been completed the operative should confirm if the damp/musty smell is still evident.

NHTSA · bulletin constructeur10241847Années modèle 2004Affiché en anglais d’origine · traduction en attenteVoir le détail →
BulletinModéréMoteurNA

Bulletin

HVAC Refrigerent Leakage - Diagnosis Guidelines Customer Statement: -HVAC not cooling or HVAC cooling less than expected

NHTSA · bulletin constructeur10235589Années modèle 2004Affiché en anglais d’origine · traduction en attenteVoir le détail →
BulletinModéréHabitacleNA

Bulletin

PSIS 750600B0001 Modification du câblage des contacteurs de boucle des prétensionneurs de ceintures de sécurité. Déclaration du client / constatations de l'atelier : ce PSIS a été émis pour informer le personnel des pièces et du service après-vente d'une modification du câblage des contacteurs de boucle des prétensionneurs de ceintures de sécurité. Si un véhicule arrive à l'atelier avec une plainte du propriétaire signalant l'allumage du voyant d'airbag et que des codes sont enregistrés pour : Résistance du contacteur de boucle de ceinture de sécurité du conducteur indéfinie, intermittente Résistance du contacteur de boucle de ceinture de sécurité du passager indéfinie, intermittente Alors la modification suivante du câblage doit être effectuée. Contexte technique : PSIS Heritage (Product Support Information Sheet). Se reporter au PDF joint pour plus de détails.

NHTSA · bulletin constructeur10210025Années modèle 1999Traduit automatiquement · original : anglaisVoir le détail →
BulletinModéréHabitacleNA

Bulletin

PSIS 750600B0001 Modification du câblage des commutateurs de boucle de ceinture de sécurité pour prétensionneurs ## Condition Ce PSIS a été émis pour informer le personnel des pièces et du service après-vente d'une modification du câblage des commutateurs de boucle sur les prétensionneurs de ceinture de sécurité. Si un véhicule entre à l'atelier avec une plainte du propriétaire concernant l'allumage du voyant d'airbag, et que des codes sont enregistrés pour : Résistance du commutateur de boucle de ceinture du conducteur indéfinie intermittente Résistance du commutateur de boucle de ceinture du passager indéfinie intermittente Alors la modification suivante du câblage doit être effectuée. ## Contexte technique PSIS d'origine (Product Support Information Sheet). Se reporter au PDF joint pour plus de détails.

NHTSA · bulletin constructeur10203236Années modèle 1999Traduit automatiquement · original : anglaisVoir le détail →
BulletinModéréFreinsNA

Bulletin

Brake noise identification. Customer statement / workshop findings: Noise complaint from the braking system. Workshop findings: The noise can be reproduced and clearly assigned to the braking system. Technical background Brake noises can be attributed to many causes. Eight of the most common causes are: - Brake discs or pads are close to their wear limit. - New brake pads and/or discs have not been properly bedded in after installation. - Aftermarket pads or discs are installed. - There is debris such as small stones, grit, road salt or sand between the brake disc and pad. - Discs are covered in rust. Rust can form when the vehicle has been stationary for long periods of time (Figure 1).

NHTSA · bulletin constructeur10201949Années modèle 2004Affiché en anglais d’origine · traduction en attenteVoir le détail →
BulletinModéréÉlectroniqueNA

Bulletin

Poor Engine Running Complaints (Misfires) Petrol Engines Only. Customer statement / workshop findings: Poor engine running, reduced power, engine warning lamp illuminated. Technical background: Technical Product Information (TPI) to assist Retailers when diagnosing poor engine running or misfire. Measure: The following TPI should be carried out sequentially to ensure the root cause and analysis of the concern are identified without unnecessary work or repetitive actions taking place.

NHTSA · bulletin constructeur10201851Années modèle 2001Affiché en anglais d’origine · traduction en attenteVoir le détail →
BulletinModéréHabitacleNA

Bulletin

Electrical switch replacement guidelines. Customer statement/workshop findings: Electrical switch suspected as defective This TPI is not applicable to suspected faulty control units or any component related to the passive restraint system in particular the airbag system Technical background: Prior to replacing an electrical switch refer to the Measure section of this TPI

NHTSA · bulletin constructeur10182390Années modèle 2004Affiché en anglais d’origine · traduction en attenteVoir le détail →
BulletinModéréFreinsNA

Bulletin

Brake noise identification. Customer statement: Noise complaint from the braking system. Workshop findings: The noise can be reproduced and clearly assigned to the braking system. Technical Background: Brake noises can be attributed to many causes. Eight of the most common causes are: 1. Brake discs or pads are close to their wear limit. 2. New brake pads and/or discs have not been properly bedded in after installation. 3. Aftermarket pads or discs are installed. 4. There is debris such as small stones, grit, road salt or sand between the brake disc and pad. 5. Discs are covered in rust. Rust can form when the vehicle has been stationary for long periods of time (Figure 1).

NHTSA · bulletin constructeur10179439Années modèle 2004Affiché en anglais d’origine · traduction en attenteVoir le détail →
BulletinModéréHabitacleNA

Bulletin

Electrical switch replacement guidelines Customer statement / workshop findings: Electrical switch suspected as defective This TPI is not applicable to suspected faulty control units or any component related to the passive restraint system in particular the airbag system Technical background: Prior to replacing an electrical switch refer to the Measure section of this TPI

NHTSA · bulletin constructeur10171209Années modèle 2004Affiché en anglais d’origine · traduction en attenteVoir le détail →
BulletinModéréÉlectroniqueNA

Bulletin

Warning light illumination. Bentley/rolls-royce. *tt

NHTSA · bulletin constructeur10012872Années modèle 1999Affiché en anglais d’origine · traduction en attenteVoir le détail →
BulletinModéréÉlectroniqueNA

Bulletin

Leak detection pump wiring. Bentley. *tt

NHTSA · bulletin constructeur10012870Années modèle 2000Affiché en anglais d’origine · traduction en attenteVoir le détail →
BulletinMineurAutreNA

Bulletin

Spurious DTC identification. Customer statement / workshop findings: Customers will not be aware of any DTCs, workshop operatives may discover spurious DTCs whilst running Guided Fault Finding (GFF) when using ODIS Technical background: To determine the course of action which should be taken the operative should refer to the Bentley Hub referencing the following: Spurious DTC list for TPI 2072055 The document contains all known spurious DTCs for all applicable vehicle variants.

NHTSA · bulletin constructeur10246358Années modèle 2004Affiché en anglais d’origine · traduction en attenteVoir le détail →
BulletinMineurCarrosserieNA

Bulletin

Telephone Functionality Complaint - Minimum Standards Required For Analysis Of Concerns. Customer statement / workshop findings: The feedback method within this TPI is required should a complaint of telephone functionality and/or quality be reported. Technical background: The minimum standards check list document within the Measure section is required to capture an accurate description of customer telephone issues.

NHTSA · bulletin constructeur10244967Années modèle 2004Affiché en anglais d’origine · traduction en attenteVoir le détail →
BulletinMineurAutreNA

Bulletin

All Vehicle Variants - Spurious DTC List. Customer statement / workshop findings: Customers will not be aware of any fault codes Workshop may discover spurious fault codes whilst running a Diagnostic Trouble Code (DTC) log as part of other investigations on the vehicle Technical background: The operative should refer to the Bentley Hub referencing TPI 2053177/- The document (loaded onto the Hub) contains all of the current known Spurious DTCs for all vehicle variants Should a particular TPI be listed as Archived, the TPI can no longer be viewed within Elsa pro, in this case please refer to the instructions within TPI 2053177/- regarding the DTC description and actions which should be conducted (if any).

NHTSA · bulletin constructeur10243663Années modèle 2004Affiché en anglais d’origine · traduction en attenteVoir le détail →
BulletinMineurCarrosserieNA

Bulletin

Speaker Replacement - Diagnostic Checks Technical Background: -There have been instances where door speakers have been changed under warranty for the complaint of sound distortion, yet when tested by ourselves and the supplier, no fault could be found with the returned unit.

NHTSA · bulletin constructeur10230822Années modèle 2004Affiché en anglais d’origine · traduction en attenteVoir le détail →
BulletinMineurCarrosserieNA

Bulletin

Telephone Functionality Complaint- Minimum Standards Required For Analysis of Concerns Customer Statement: -The feedback method within this TPI is required should a complaint of telephone functionality and/or quality be reported.

NHTSA · bulletin constructeur10226802Années modèle 2004Affiché en anglais d’origine · traduction en attenteVoir le détail →
BulletinMineurCarrosserieNA

Bulletin

Speaker Replacement - Diagnostic checks. Customer statement / workshop findings: Audio output from speakers is distorted Technical background: There have been instances where door speakers have been changed under warranty for the complaint of sound distortion, yet when tested by ourselves and the supplier, no fault could be found with the returned unit. Production change: All speakers are subjected to a dynamic test and the individual results recorded for future reference

NHTSA · bulletin constructeur10201883Années modèle 2004Affiché en anglais d’origine · traduction en attenteVoir le détail →
BulletinMineurCarrosserieNA

Bulletin

Telephone Functionality Complaint - Minimum Standards Required For Analysis Of Concerns. Customer statement / workshop findings: The feedback method within this TPI is required should a complaint of telephone functionality and/or quality be reported. Technical background: The minimum standards check list document within the Measure section is required to capture an accurate description of customer telephone issues.

NHTSA · bulletin constructeur10183483Années modèle 2004Affiché en anglais d’origine · traduction en attenteVoir le détail →
BulletinMineurMoteurNA

Bulletin

Poor Engine Running Complaints (Misfires) Petrol Engines Only

NHTSA · bulletin constructeur10142962Années modèle 2001Affiché en anglais d’origine · traduction en attenteVoir le détail →
BulletinMineurÉlectroniqueNA

Bulletin

Bentley : les feux arrière ne sont plus disponibles en tant qu'ensemble complet. Modèles Bentley Arnage et Rolls-Royce Silver Seraph. Aucune année modèle indiquée. *pe

NHTSA · bulletin constructeur10044520Années modèle 2009Traduit automatiquement · original : anglaisVoir le détail →
BulletinMineurMoteurNA

Bulletin

Bentley: Fuel filler caps. There are the standard fitted black plastic fuel filler cap for mulsanne/arnage and the jewel fuel filler cap fitted for continental. Black plastic fuel filler cap not to be placed on continental and jewel fuel filler cap not to be placed on mulsanne/arnage. This will reduce fuel tanks capability to breath and vent correctly. No model years were listed. *pe

NHTSA · bulletin constructeur10036953Années modèle 2009Affiché en anglais d’origine · traduction en attenteVoir le détail →
Plus anciens →

Sources : NHTSA (États-Unis, domaine public), Transports Canada (Licence du gouvernement ouvert – Canada), DVSA (Royaume-Uni, Open Government Licence v3.0), RappelConso et Safety Gate de l'UE (France, Licence Ouverte 2.0), MLIT (Japon, licence de données publiques 1.0) et MOLIT (Corée du Sud, car.go.kr).