Lecture libre · compte gratuit pour contribuerSuccesseur d’Anticars (2000)

BMW M6

1983–2019 · 3 générations · 1 défauts documentés · 3 marchés
Générations

Les bulletins techniques (TSB) sont des instructions de réparation que les constructeurs envoient à leurs concessionnaires sur des problèmes connus. Ce ne sont pas des rappels de sécurité, mais ils confirment souvent un défaut.

Année modèle
MarchéTousNA
M6 (F06/F12/F13) · 2012–2019
BulletinModéréMoteurNA

Bulletin

"N63 and S63 Engine: Upper Oil Pan Removal and Installation Procedures. INFORMATION When removing and/or installing the N63 or S63 engine ""upper"" oil pan assembly, the oil pan can sustain damage if this operation is not performed correctly. Before loosening or tightening the upper oil pan bolts as per Repair Instruction 11 13 010 ""Removing and installing /replacing upper oil sump (N63),"" the steps outlined in the attachment of this bulletin must be followed. Refer to attached document and the instruction section that applies to the procedure being carried out. The ISTA/D repair instructions are currently being revised."

NHTSA · bulletin constructeur10151400Années modèle 2013Affiché en anglais d’origine · traduction en attenteVoir le détail →
M6 (F06/F12/F13) · 2012–2019
BulletinModéréMoteurNA

Bulletin

N63 and S63 Engine: Valve Seal Replacement This Service Information bulletin and attachment supersedes SI B11 08 15 dated March 2016. Refer to the following applicable SIBs before replacing the valve seals. SI B11 07 11 - Turbocharger Failure: Oil Supply and Return Line Blockage and Proper Repairs SI B11 07 12 - N63 Engine: Oil Consumption and/or Rough Running Complaints SI B11 01 13 - N63 Engine: Engine Oil Consumption, Engine Oil Top-ups and Refill Capacity SI B11 03 13 - Engine Oil Consumption (all models) If the valve seals are leaking, one of the following will help determine if the seals should be replaced. Smoke from the tailpipe when starting or aggressively accelerating and decelerating the engine Excessive engine oil consumption Spark plugs fouled with engine oil

NHTSA · bulletin constructeur10151301Années modèle 2013Affiché en anglais d’origine · traduction en attenteVoir le détail →
M6 (F06/F12/F13) · 2012–2019
BulletinModéréMoteurNA

Bulletin

This Service Information bulletin and attachment supersedes SI B11 08 15 dated November 2015. SUBJECT N63 and S63 Engine: Valve Seal Replacement. Refer to the following applicable SIBs before replacing the valve seals. SI B11 07 11 - Turbocharger Failure: Oil Supply and Return Line Blockage and Proper Repairs SI B11 07 12 - N63 Engine: Oil Consumption and/or Rough Running Complaints SI B11 01 13 - N63 Engine: Engine Oil Consumption, Engine Oil Top-ups and Refill Capacity SI B11 03 13 - Engine Oil Consumption (all models) If the valve seals are leaking, one of the following will help determine if the seals should be replaced. Smoke from the tailpipe when starting or aggressively accelerating and decelerating the engine Excessive engine oil consumption Spark plugs fouled with engine oil

NHTSA · bulletin constructeur10151248Années modèle 2013Affiché en anglais d’origine · traduction en attenteVoir le détail →
M6 (F06/F12/F13) · 2012–2019
BulletinModéréMoteurNA

Bulletin

This Service Information bulletin and attachment supersedes SI B11 08 15 dated November 2015. SUBJECT N63 and S63 Engine: Valve Seal Replacement. Refer to the following applicable SIBs before replacing the valve seals. B11 07 11 - Turbocharger Failure: Oil Supply and Return Line Blockage and Proper Repairs B11 07 12 - N63 Engine: Oil Consumption and/or Rough Running Complaints B11 01 13 - N63 Engine: Engine Oil Consumption, Engine Oil Top-ups and Refill Capacity B11 03 13 - Engine Oil Consumption (all models) If the valve seals are leaking, one of the following will help determine if the seals should be replaced. Smoke from the tailpipe when starting or aggressively accelerating and decelerating the engine Excessive engine oil consumption Spark plugs fouled with engine oil

NHTSA · bulletin constructeur10151165Années modèle 2013Affiché en anglais d’origine · traduction en attenteVoir le détail →
M6 (F06/F12/F13) · 2012–2019
BulletinModéréMoteurNA

Bulletin

N63 and S63 Engine: Valve Seal Replacement. Refer to the following applicable SIBs before replacing the valve seals. * B11 07 11 - Turbocharger Failure: Oil Supply and Return Line Blockage and Proper Repair * B11 07 12 - N63 Engine: Oil Consumption and/or Rough Running Complaints * B11 01 13 - N63 Engine: Engine Oil Consumption, Engine Oil Top-ups and Refill Capacity * B11 03 13 - Engine Oil Consumption (all models) If the valve seals are leaking, one of the following will help determine if the seals should be replaced. * Smoke from the tailpipe when starting or aggressively accelerating and decelerating the engine in addition to excessive engine oil consumption * Spark plugs fouled with engine oil and excessive engine oil consumption * Excessive engine oil consumption All Vehicles: On vehicles, where an excessive oil consumption between services is the only complaint, a complete oil consumption test as described in SI B11 03 13, must be performed first before replacing the valve seals. On vehicles exhibiting reproducible smoking from the tailpipe when hot, additional engine diagnostic steps (e.g. engine compression test, leak-down tests; inspection of the crankcase ventilation lines and turbo intake/outlet tubes for excessive oil accumulation) should be performed and documented prior to replacement of the valve seals, in order to eliminate other possible causes. Refer to the SIBs listed above for important diagnostic tips. Do not remove the intake manifolds to clean the intake valve carbon.

NHTSA · bulletin constructeur10149960Années modèle 2013Affiché en anglais d’origine · traduction en attenteVoir le détail →
M6 (F06/F12/F13) · 2012–2019
BulletinModéréMoteurNA

Bulletin

S63TU Engine: Noises from Leaking Exhaust Manifold. A rattling, knocking, clattering or hissing noise can be heard from the engine compartment while the engine is running. It is more pronounced when the engine is under load. CAUSE The exhaust manifold attaching screws have come loose, causing an exhaust leak.

NHTSA · bulletin constructeur10148251Années modèle 2013Affiché en anglais d’origine · traduction en attenteVoir le détail →
M6 (F06/F12/F13) · 2012–2019
BulletinModéréMoteurNA

Bulletin

N63 Engine: Valve Seal Replacement. Refer to the following applicable SIBs before replacing the valve seals. ? B11 07 11 - Turbocharger Failure: Oil Supply and Return Line Blockage and Proper Repairs ? B11 07 12 - N63 Engine: Oil Consumption and/or Rough Running Complaints ? B11 01 13 - N63 Engine: Engine Oil Consumption, Engine Oil Top-ups and Refill Capacity ? B11 03 13 - Engine Oil Consumption (all models) If the valve seals are leaking, one of the following will help determine if the seals should be replaced. ? Smoke from the tailpipe when starting or aggressively accelerating and decelerating the engine ? Excessive engine oil consumption ? Spark plugs fouled with engine oil

NHTSA · bulletin constructeur10147808Années modèle 2013Affiché en anglais d’origine · traduction en attenteVoir le détail →
M6 (F06/F12/F13) · 2012–2019
BulletinModéréMoteurNA

Bulletin

?N63 Engine: Valve Seal Replacement. Refer to the following applicable SIBs before replacing the valve seals. B11 07 11 - Turbocharger Failure: Oil Supply and Return Line Blockage and Proper Repairs B11 07 12 - N63 Engine: Oil Consumption and/or Rough Running Complaints B11 01 13 - N63 Engine: Engine Oil Consumption, Engine Oil Top-ups and Refill Capacity B11 03 13 - Engine Oil Consumption (all models) If the valve seals are leaking, one of the following will help determine if the seals should be replaced. Smoke from the tailpipe when starting or aggressively accelerating and decelerating the engine Excessive engine oil consumption Spark plugs fouled with engine oil.

NHTSA · bulletin constructeur10147759Années modèle 2013Affiché en anglais d’origine · traduction en attenteVoir le détail →
M6 (F06/F12/F13) · 2012–2019
BulletinModéréMoteurNA

Bulletin

N63 and S63 Engine: Valve Seal Replacement This Service Information bulletin replaces SI B11 08 15 June May 2017 What's New: Diagnostic tips updated. Refer to the following applicable SIBs before replacing the valve seals. B11 07 11 - Turbocharger Failure: Oil Supply and Return Line Blockage and Proper Repair B11 07 12 - N63 Engine: Oil Consumption and/or Rough Running Complaints B11 01 13 - N63 Engine: Engine Oil Consumption, Engine Oil Top-ups and Refill Capacity B11 03 13 - Engine Oil Consumption (all models) If the valve seals are leaking, one of the following will help determine if the seals should be replaced. Smoke from the tailpipe when starting or aggressively accelerating and decelerating the engine in addition to excessive engine oil consumption Spark plugs fouled with engine oil and excessive engine oil consumption Excessive engine oil consumption Vehicles with less than 40,000 miles should not be considered for valve seal replacement. All Vehicles: A complete oil consumption test, as described inSI B11 03 13, must be performed first, before replacing the valve seals. Do not remove the intake manifolds to clean the intake valve carbon.

NHTSA · bulletin constructeur10146706Années modèle 2013Affiché en anglais d’origine · traduction en attenteVoir le détail →
M6 (F06/F12/F13) · 2012–2019
BulletinModéréMoteurNA

Bulletin

Bmw: Check coolant message illuminated. According to the dealer there are traces of coolant leaking into the engine compartment at the turbochargers. Vehicles with s63t engine. *kb

NHTSA · bulletin constructeur10053584Années modèle 2013Affiché en anglais d’origine · traduction en attenteVoir le détail →
M6 (F06/F12/F13) · 2012–2019
BulletinMineurMoteurNA

Bulletin

Transition de la référence de l'huile moteur MINI et huiles moteur du millésime 2016

NHTSA · bulletin constructeur10216758Années modèle 2016Traduit automatiquement · original : anglaisVoir le détail →
M6 (F06/F12/F13) · 2012–2019
BulletinMineurMoteurNA

Bulletin

TEC26 Turbo Charger Return

NHTSA · bulletin constructeur10216793Années modèle 2016Affiché en anglais d’origine · traduction en attenteVoir le détail →
M6 (F06/F12/F13) · 2012–2019
BulletinMineurMoteurNA

Bulletin

"This Service Information bulletin and attachment supersedes SI B11 16 14 dated May 2015. designates changes to this revision SUBJECT N63 Engine: Check the Timing Chain. INFORMATION This bulletin outlines the procedure for checking the engine timing chains for wear, and should be completed in conjunction with SI B11 06 14, ""N63 Customer Care Package."" The N63CCP and N63 Engine Check the Timing Chain are NOT mandatory Technical Campaigns or Recalls. They should be completed only based on parts availability, workshop capacity, and the customer's schedule. Performing the test plans identified in the procedure below will detect wear at an early stage and, if necessary, provide a repair solution. To avoid future valvetrain wear, the vehicle must be reprogrammed and a shorter oil service interval must be retrofitted via ISTA/P. Finally, drain and replace the engine's oil and filter. After completing all necessary repairs included in the N63 Customer Care Package and the Timing Chain Check, the vehicle must be test driven for up to 30 minutes to ensure that the repairs were performed to the highest standard."

NHTSA · bulletin constructeur10151071Années modèle 2013Affiché en anglais d’origine · traduction en attenteVoir le détail →
M6 (F06/F12/F13) · 2012–2019
BulletinMineurMoteurNA

Bulletin

N63 Engine: Check the Timing Chain. INFORMATION This bulletin outlines the procedure to check the engine timing chains for wear and should be completed in conjunction with SI B11 06 14 "N63 Customer Care Package". Performing the test plans identified in the procedure below will detect wear at an early stage and if necessary provide a repair solution. To avoid future valvetrain wear, the vehicle must be reprogrammed and a shorter oil service interval must be retrofitted via ISTA/P. Finally, drain and replace the engine's oil and filter. After completing all necessary repairs included in the N63 Customer Care Package and the Timing Chain Check, the vehicle must be test driven for up to 30 minutes to assure the highest standard of performed repairs.

NHTSA · bulletin constructeur10148163Années modèle 2013Affiché en anglais d’origine · traduction en attenteVoir le détail →
M6 (F06/F12/F13) · 2012–2019
BulletinMineurMoteurNA

Bulletin

"This bulletin outlines the procedure for checking the engine timing chains for wear, and should be completed in conjunction with SI B11 06 14, ""N63 Customer Care Package."" The N63CCP and N63 Engine Check the Timing Chain are NOT mandatory Technical Campaigns or Recalls. They should be completed only based on parts availability, workshop capacity, and the customer's schedule. Performing the test plans identified in the procedure below will detect wear at an early stage and, if necessary, provide a repair solution. To avoid future valvetrain wear, the vehicle must be reprogrammed and a shorter oil service interval must be retrofitted via ISTA/P. Finally, drain and replace the engine's oil and filter. After completing all necessary repairs included in the N63 Customer Care Package and the Timing Chain Check, the vehicle must be test driven for up to 30 minutes to ensure that the repairs were performed to the highest standard. AFFECTED VEHICLES This Service Action applies to E70, E71, E72, F01, F02, F04, F07, F10, F12, and F13 vehicles with the N63 engines corresponding to the production dates listed above. First check if a Service Action label with a code number 728 is already attached to the B-pillar. If a code number 728 has already been punched out, the Campaign has already been performed and no further action is necessary. Eligible vehicles will show the following Service Action-related Campaign Code: 00 13 48 02 00 If the vehicle already has a label from a previous Service Action/Recall Campaign, affix the new label next to the old one. Do not affix one label on top of another one, because a number from an underlying label could appear in the punched-out hole of the new label."

NHTSA · bulletin constructeur10147656Années modèle 2013Affiché en anglais d’origine · traduction en attenteVoir le détail →
M6 (F06/F12/F13) · 2012–2019
BulletinMineurMoteurNA

Bulletin

"This bulletin outlines the procedure for checking the engine timing chains for wear, and should be completed in conjunction with SI B11 06 14, ""N63 Customer Care Package."" The N63CCP and N63 Engine Check the Timing Chain are NOT mandatory Technical Campaigns or Recalls. They should be completed only based on parts availability, workshop capacity, and the customer's schedule. Performing the test plans identified in the procedure below will detect wear at an early stage and, if necessary, provide a repair solution. To avoid future valvetrain wear, the vehicle must be reprogrammed and a shorter oil service interval must be retrofitted via ISTA/P. Finally, drain and replace the engine's oil and filter. After completing all necessary repairs included in the N63 Customer Care Package and the Timing Chain Check, the vehicle must be test driven for up to 30 minutes to ensure that the repairs were performed to the highest standard."

NHTSA · bulletin constructeur10147127Années modèle 2013Affiché en anglais d’origine · traduction en attenteVoir le détail →
M6 (F06/F12/F13) · 2012–2019
BulletinMineurMoteurNA

Bulletin

"This Service Information bulletin and attachment supersedes SI B11 16 14 dated January 2015. designates changes to this revision SUBJECT N63 Engine: Check the Timing Chain. INFORMATION This bulletin outlines the procedure for checking the engine timing chains for wear, and should be completed in conjunction with SI B11 06 14, ""N63 Customer Care Package."" The N63CCP and N63 Engine Check the Timing Chain are NOT mandatory Technical Campaigns or Recalls. They should be completed only based on parts availability, workshop capacity, and the customer's schedule. Performing the test plans identified in the procedure below will detect wear at an early stage and, if necessary, provide a repair solution. To avoid future valvetrain wear, the vehicle must be reprogrammed and a shorter oil service interval must be retrofitted via ISTA/P. Finally, drain and replace the engine's oil and filter. After completing all necessary repairs included in the N63 Customer Care Package and the Timing Chain Check, the vehicle must be test driven for up to 30 minutes to ensure that the repairs were performed to the highest standard."

NHTSA · bulletin constructeur10147068Années modèle 2013Affiché en anglais d’origine · traduction en attenteVoir le détail →

Sources : NHTSA (États-Unis, domaine public), Transports Canada (Licence du gouvernement ouvert – Canada), DVSA (Royaume-Uni, Open Government Licence v3.0), RappelConso et Safety Gate de l'UE (France, Licence Ouverte 2.0), MLIT (Japon, licence de données publiques 1.0) et MOLIT (Corée du Sud, car.go.kr).