Lecture libre · compte gratuit pour contribuerSuccesseur d’Anticars (2000)

DodgeDodge Nitro

2006–2011 · 14 défauts documentés · 3 marchés

Les bulletins techniques (TSB) sont des instructions de réparation que les constructeurs envoient à leurs concessionnaires sur des problèmes connus. Ce ne sont pas des rappels de sécurité, mais ils confirment souvent un défaut.

Année modèle
MarchéTousEUNAUK
BulletinModéréAutreNA

Bulletin

wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK

NHTSA · bulletin constructeur10236933Années modèle 2012Affiché en anglais d’origine · traduction en attenteVoir le détail →
BulletinModéréMoteurNA

Bulletin

Issue involves overheating, running hot, coolant leaks and related symptoms after a Mopar replacement engine has been installed in the vehicle.

NHTSA · bulletin constructeur10230180Années modèle 2012Affiché en anglais d’origine · traduction en attenteVoir le détail →
BulletinModéréMoteurNA

Bulletin

Issue involves overheating, running hot, coolant leaks and related symptoms after a Mopar replacement engine has been installed in the vehicle.

NHTSA · bulletin constructeur10221594Années modèle 2012Affiché en anglais d’origine · traduction en attenteVoir le détail →
BulletinModéréMoteurNA

Bulletin

Part Description: 5.7L Long Block Issue Description: This 5.7L Long Block Assembly is compatible with both EGR and Non-EGR applications. An EGR Block-Off Plate (53032739AA) must be ordered when installing this Long Block Assembly in a Non-EGR application. Unless, the EGR Block-Off Plate is being transferred from the old engine.

NHTSA · bulletin constructeur10229181Années modèle 2007Affiché en anglais d’origine · traduction en attenteVoir le détail →
BulletinModéréMoteurNA

Bulletin

Service - Four Piece Oil Pan Gasket All Cummins Equipped Vehicles ONLY - The replacement oil pan gasket can be a four piece gasket rather than a single piece gasket. This applies to Cummins 5.9L and 6.7L engines only. Installation: 1. Clean the oil pan T-joints.~ 2. Fill the T-joint between the pan rail/gear housing and pan rail/rear seal retainer with sealant. Use Mopar Silicone Rubber Adhesive Sealant or equivalent. 3. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the oil pan flange.~ 4. The four piece gasket will need to be assembled to make a complete oil pan gasket. 5. Lay the oil pan gasket(s) onto the oil pan flange.~ 6. Ensure the oil pan gasket segment joints are properly aligned. 7. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the top of the oil pan gasket.~ 8. Install the oil pan. Starting from the center and working outward, tighten the oil pan bolts to 28 Nm [21 ft. lbs.].

NHTSA · bulletin constructeur10223854Années modèle 2007Affiché en anglais d’origine · traduction en attenteVoir le détail →
BulletinModéréFreinsNA

Bulletin

Adaptive Cruise Control Sensor 1) If you are replacing this part due to the cluster displaying Clean Radar Sensor in Front of Vehicle or DTC C1266 ACC Sensor Blinded, please verify that there is no blockage in front of the sensor. Blockage can occur from mud, ice, snow, front end damage, bracket damage, the sensor not attached to the bracket properly or an aftermarket fascia installed. This fault can occur intermittently in muddy or icy/snowy conditions and is considered normal operation. Under some circumstances, a misaligned sensor can also cause the C1266 DTC, please complete an alignment procedure. No replacement is required.~ 2) If you are replacing this part due to the cluster displaying ?ACC/FCW Unavailable Service Required?, please check the DTC fault codes. This will indicate which module needs to be serviced (TCM, PCM, ESP/ABS, etc). This fault is not due to the ACC Sensor. No sensor replacement is required.~ 3) If you have fault code DTC C125E ACC Sensor Adjustment Required, please verify that the radar sensor is fully seated in the clips and there is no damage (if clips are damaged on a 2013 or earlier vehicle, order P/N 68085813A$, otherwise please replace the module), please verify there is no blockage to the sensor due to mud, ice, snow, front end damage, bracket damage or the sensor not attached to the bracket properly. Perform the Vertical Alignment and the Electronic Horizontal Alignments procedure as stated in the service manual. Please note, if the horizontal alignment procedure will not complete, check the vertical alignment and confirm that the sensor is seated properly. Rerun the horizontal alignment procedure. No sensor replacement is required. **Hints for running Horizontal Alignment procedure: A) Verify speed is between 45 and 75 mph, B) verify the road is relatively straight with signs, poles, guard rails, etc C) Do not tail a vehicle too closely this inhibits the learning procedure

NHTSA · bulletin constructeur10139956Années modèle 2012Affiché en anglais d’origine · traduction en attenteVoir le détail →
BulletinModéréMoteurNA

Bulletin

Ram/dodge\jeep service campaign: See document search button for owner letter. The engine water pump on certain vehicles may leak coolant. Engine operation with a low coolant level could cause engine damage or low cabin heater output. Csc letter was rec'd. *pe

NHTSA · bulletin constructeur10034071Années modèle 2010Affiché en anglais d’origine · traduction en attenteVoir le détail →
BulletinModéréMoteurNA

Bulletin

Chrysler\dodge service campaign: See document search button for owner letter. An incorrect positive crankcase ventilation (pcv) valve may have been installed. An incorrect pcv valve can cause excessive exhaust emissions. Csc letter was received. *pe

NHTSA · bulletin constructeur10028832Années modèle 2009Affiché en anglais d’origine · traduction en attenteVoir le détail →
BulletinModéréÉlectroniqueNA

Bulletin

Emissions recall g45--veci label - an incorrect vehicle emission control information (veci) label was installed on about ten thousand vehicles. The originally installed veci label does not display the correct spark plug information. *nj

NHTSA · bulletin constructeur10023661Années modèle 2007Affiché en anglais d’origine · traduction en attenteVoir le détail →
BulletinModéréSuspensionNA

Bulletin

Slight play in steering/stiff/choppy/bumpy ride. *nj

NHTSA · bulletin constructeur10023393Années modèle 2007Affiché en anglais d’origine · traduction en attenteVoir le détail →
BulletinModéréSuspensionNA

Bulletin

Steering angle sensor - not initialized/internal. *kb

NHTSA · bulletin constructeur10021984Années modèle 2007Affiché en anglais d’origine · traduction en attenteVoir le détail →
BulletinMineurAutreNA

Bulletin

LIFTER, Hydraulic Roller Deactivating Please do not replace MDS lifters because the disconnecting pin is not lined up, this is normal and not a defect.

NHTSA · bulletin constructeur10248517Années modèle 2012Affiché en anglais d’origine · traduction en attenteVoir le détail →
BulletinMineurAutreNA

Bulletin

LIFTER, Hydraulic Roller Deactivating Please do not replace MDS lifters because the disconnecting pin is not lined up, this is normal and not a defect.

NHTSA · bulletin constructeur10244356Années modèle 2012Affiché en anglais d’origine · traduction en attenteVoir le détail →
BulletinMineurAutreNA

Bulletin

KEY, Master If replacing the key/FOBIK on a WJ, KJ, TJ, or PT Cruiser, use the "AC" NIC level part number. The "AB" NIC level will not program to these platforms. For all other platforms, if the "AB" NIC level will not program to the vehicle, use the "AC" NIC level part and submit a part warranty.

NHTSA · bulletin constructeur10229256Années modèle 2005Affiché en anglais d’origine · traduction en attenteVoir le détail →
BulletinMineurBoîteNA

Bulletin

Customer Satisfaction Notification V51 Reprogram Powertrain Control Module

NHTSA · bulletin constructeur10228020Années modèle 2010Affiché en anglais d’origine · traduction en attenteVoir le détail →
BulletinMineurHabitacleNA

Bulletin

Warranty Bulletin D-20-17 (X85) Active Head Restraint - Select 2012-2013 Jeep Liberty (KK) and 2012 Dodge Nitro (KA) (Rev. A)

NHTSA · bulletin constructeur10224064Années modèle 2012Affiché en anglais d’origine · traduction en attenteVoir le détail →
BulletinMineurAutreNA

Bulletin

KEY, Master If replacing the key/FOBIK on a WJ, KJ, TJ, or PT Cruiser, use the "AC" NIC level part number. The "AB" NIC level will not program to these platforms. For all other platforms, if the "AB" NIC level will not program to the vehicle, use the "AC" NIC level part and submit a part warranty.

NHTSA · bulletin constructeur10221686Années modèle 2005Affiché en anglais d’origine · traduction en attenteVoir le détail →
BulletinMineurBoîteNA

Bulletin

Gear Ratio DTC?s, Transmission Shift Concerns, Does Not Shift At Times, Shudders

NHTSA · bulletin constructeur10221150Années modèle 2012Affiché en anglais d’origine · traduction en attenteVoir le détail →
BulletinMineurBoîteNA

Bulletin

Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.

NHTSA · bulletin constructeur10220840Années modèle 2005Affiché en anglais d’origine · traduction en attenteVoir le détail →
BulletinMineurHabitacleNA

Bulletin

Warranty Bulletin D-20-21 (X91) Active Head Restraint - Select 2010 Dodge Journey (JC), Dodge Avenger/Chrysler Sebring (JS), Dodge Nitro (KA), Jeep Liberty (KK), Jeep Compass/Jeep Patriot (MK), Dodge Caliber (PM), Dodge Caravan (RT)

NHTSA · bulletin constructeur10187658Années modèle 2010Affiché en anglais d’origine · traduction en attenteVoir le détail →
BulletinMineurHabitacleNA

Bulletin

Warranty Bulletin D-20-22 (X92) Active Head Restraint - Select 2011 Dodge Journey (JC), Dodge Avenger/Chrysler 200 (JS), Dodge Nitro (KA), Jeep Liberty (KK), Jeep Compass/Jeep Patriot (MK), Dodge Caliber (PM), Dodge Caravan (RT), Dodge Durango (WD), Jeep Grand Cherokee (WK)

NHTSA · bulletin constructeur10187659Années modèle 2011Affiché en anglais d’origine · traduction en attenteVoir le détail →
BulletinMineurHabitacleNA

Bulletin

Warranty Bulletin D-20-17 (X85) Active Head Restraint - Select 2012-2013 Jeep Liberty (KK) and 2012 Dodge Nitro (KA) (Rev. B)

NHTSA · bulletin constructeur10187663Années modèle 2012Affiché en anglais d’origine · traduction en attenteVoir le détail →
BulletinMineurHabitacleNA

Bulletin

Warranty Bulletin D-20-21 (X91) Active Head Restraint - Select 2010 Dodge Journey (JC), Dodge Avenger/Chrysler Sebring (JS), Dodge Nitro (KA), Jeep Liberty (KK), Jeep Compass/Jeep Patriot (MK), Dodge Caliber (PM), Dodge Caravan/Chrysler Town & Country (RT) (Rev. A)

NHTSA · bulletin constructeur10187667Années modèle 2010Affiché en anglais d’origine · traduction en attenteVoir le détail →
BulletinMineurHabitacleNA

Bulletin

Active Head Restraint (AHR) Inadvertent Deployment - X92 Warranty Extension This bulletin involves inspecting the sled bracket striker pin and possibly replacing a front seat AHR that has inadvertently deployed. Customers may comment on the following:The AHR is deployed on one or both front seats and will not reset.

NHTSA · bulletin constructeur10187680Années modèle 2011Affiché en anglais d’origine · traduction en attenteVoir le détail →
BulletinMineurHabitacleNA

Bulletin

Active Head Restraint (AHR) Inadvertent Deployment - X91 Warranty Extension This bulletin involves inspecting the sled bracket striker pin and possibly replacinga front seat AHR that has inadvertently deployed. Customers may comment on the following: The AHR is deployed on one or both front seats and will not reset.

NHTSA · bulletin constructeur10187684Années modèle 2010Affiché en anglais d’origine · traduction en attenteVoir le détail →
Plus anciens →

Sources : NHTSA (États-Unis, domaine public), Transports Canada (Licence du gouvernement ouvert – Canada), DVSA (Royaume-Uni, Open Government Licence v3.0), RappelConso et Safety Gate de l'UE (France, Licence Ouverte 2.0), MLIT (Japon, licence de données publiques 1.0) et MOLIT (Corée du Sud, car.go.kr).