Les bulletins techniques (TSB) sont des instructions de réparation que les constructeurs envoient à leurs concessionnaires sur des problèmes connus. Ce ne sont pas des rappels de sécurité, mais ils confirment souvent un défaut.
Some customers may experience a SBS/SCBS, LAS/LDWS and/or HBC warning light on. A system error message may also be found in the center display. DTC U3000:04-0A (Forward sensing camera (FSC) internal malfunction). DTC U3000:04-0A (Forward sensing camera (FSC) internal malfunction) is stored in the FSC module and cannot be erased. This concern may be caused by a hardware failure of an internal device of the FSC, which results in a malfunction detection. To eliminate this concern, the production process of the FSC has been modified.
NHTSA · bulletin constructeur10199641Années modèle 2021Affiché en anglais d’origine · traduction en attenteVoir le détail →
If you experience issues with the current version of ID's such as missing tools or modules not showing after completing a network test, be advised that we are aware of these issues and are working to resolve them. As a counter measure, it is advised that you un-install ids and re-install version 103.00 and "do not update" until further notice.
NHTSA · bulletin constructeur10185813Années modèle 2017Affiché en anglais d’origine · traduction en attenteVoir le détail →
Certains clients peuvent se plaindre de l'un des points suivants :
1. L'écran du centre d'infodivertissement ne fournit pas le code d'autorisation (OTP) lors de l'inscription du véhicule connecté à l'application MyMazda.
2. Une ou plusieurs fonctions à distance sont inopérantes.
NHTSA · bulletin constructeur11039110Années modèle 2021Traduit automatiquement · original : anglaisVoir le détail →
Certains véhicules peuvent présenter le voyant de contrôle moteur allumé avec le code DTC P0300:00 (Ratés d'allumage aléatoires détectés) enregistré. Cela peut être dû à une détection erronée de raté d'allumage causée par une logique de commande du PCM inadéquate. Pour éliminer ce problème, la logique de commande du PCM a été modifiée.
NHTSA · bulletin constructeur11012337Années modèle 2021Traduit automatiquement · original : anglaisVoir le détail →
Certains clients peuvent remarquer que le voyant de charge s'allume pendant la conduite. Lors de l'inspection, le code DTC P2502:00 PCM (Dysfonctionnement de la tension générée par l'alternateur) est enregistré en mémoire. Cela peut être dû à une résistance entre la carte de circuit imprimé et la masse. Lorsqu'un courant électrique de forte intensité traverse le circuit, la position de la borne de masse peut ne pas être suffisamment efficace. Pour éliminer ce problème, le logiciel de commande du convertisseur CC/CC a été modifié. De plus, la procédure de production a été révisée. Le couple de serrage de la borne de masse et de la carte de circuit imprimé a été augmenté.
NHTSA · bulletin constructeur11008418Années modèle 2021Traduit automatiquement · original : anglaisVoir le détail →
Some customers may experience a check engine light illumination at idle while stopped with DTC P0300:00 stored, resulting in rough idle conditions. P0300:00: Random misfire detected This concern is caused by improper engine control in the idle range. To eliminate the concern, the PCM control software has been modified.
NHTSA · bulletin constructeur11008417Années modèle 2021Affiché en anglais d’origine · traduction en attenteVoir le détail →
Some customers may experience the CHECK ENGINE light ON with DTC P0089:00 (Spill valve control solenoid valve control circuit range/performance problem) stored. This is caused by improper control software of the PCM detecting a false error, even with normal fuel pressure operation. To correct this issue, the control software of the PCM has been modified.
NHTSA · bulletin constructeur10190951Années modèle 2021Affiché en anglais d’origine · traduction en attenteVoir le détail →
Some vehicles may experience the check engine light on with DTCs P2096:00, P2097:00 and/or P0524:00 that cannot be cleared by itself, and the check engine light stays on even if the detection condition has gone. P2096:00 - Air fuel too lean P2097:00 - Air fuel too rich P0524:00 - Engine oil pressure too low. This concern may be caused by improper PCM control logic. The PCM software has been modified to eliminate this concern.
NHTSA · bulletin constructeur10180595Années modèle 2019Affiché en anglais d’origine · traduction en attenteVoir le détail →
New IDs software version 102.00 and Update 102.01 is now available on MS3 IDs update 102.00 and 102.01 is now available on MS3 under the "IDs/Infotainment" tab.
NHTSA · bulletin constructeur10186918Années modèle 2017Affiché en anglais d’origine · traduction en attenteVoir le détail →
Active driving display opens/closes improperly. Some vehicles may exhibit the active driving display opening/closing improperly as described below: * It does not open or close when the ignition is turned ON or OFF . * The display operation does not fully open/close. * It closes and then opens by itself while the vehicle is moving. This concern may be caused by voltage fluctuation to the act ive driving display which activates pinching detection. Customer having this concern should have their vehicle repaired using the following repair procedure.
NHTSA · bulletin constructeur10186257Années modèle 2016Affiché en anglais d’origine · traduction en attenteVoir le détail →
Some customers may experience the active driving display (auto flip-up type) does not flip up and no DTC is stored. Due to improper assembly, a deformed bracket may cause a loose mesh between internal gears. To correct this issue, the active driving display has been changed.
NHTSA · bulletin constructeur10144332Années modèle 2018Affiché en anglais d’origine · traduction en attenteVoir le détail →
If the right-side bsm control module requires replacement for any repair, also replace the left side bsm control module to complete the radar aiming procedure (it is ok to replace the left bsm alone). Reason if the right-side bsm control module is replaced alone, automatic configuration is not performed due to a program error in the module. Because of this, the required bsm radar aiming cannot be performed. Automatic configuration as well as bsm radar aiming can be performed, if the left-side bsm control module is replaced alone or together with the right-side bsm control module.
NHTSA · bulletin constructeur10105642Années modèle 2016Affiché en anglais d’origine · traduction en attenteVoir le détail →
If the right-side bsm control module requires replacement for any repair, also replace the left side bsm control module to complete the radar aiming procedure (it is ok to replace the left bsm alone). Reason if the right-side bsm control module is replaced alone, automatic configuration is not performed due to a program error in the module. Because of this, the required bsm radar aiming cannot be performed. Automatic configuration as well as bsm radar aiming can be performed, if the left-side bsm control module is replaced alone or together with the right-side bsm control module.
NHTSA · bulletin constructeur10101468Années modèle 2016Affiché en anglais d’origine · traduction en attenteVoir le détail →
If the active driving display (ad-disp) unit requires removal, use caution when disconnecting/connecting the wiring harness. If the harness is not connected properly, the ad-disp may not operate.
NHTSA · bulletin constructeur10091601Années modèle 2016Affiché en anglais d’origine · traduction en attenteVoir le détail →
If the active driving display (ad-disp) unit requires removal, use caution when disconnecting/connecting the wiring harness. If the harness is not connected properly, the ad-disp may not operate.
NHTSA · bulletin constructeur10090667Années modèle 2016Affiché en anglais d’origine · traduction en attenteVoir le détail →
Bsm radar aiming cannot be performed after right-side bsm control module replacement. If right-dide bsm control module requres replacement for any repair, also replace left side bsm control module to compelte the radar aiming procedure (it's ok to replace the left bsm alone). If the right-side bsm control module is replaced alone, "automatic configuration" is not performed due to program error in module. Because of this, the required "bsm radar aiming" cannot be performed. "automatic configuration" as well as "bsm radar aiming" can be performed if left-side bsm control module is replaced alone or together with right-side bsm control module.
NHTSA · bulletin constructeur10076685Années modèle 2016Affiché en anglais d’origine · traduction en attenteVoir le détail →
Mazda: There is condensation and fog in the front and rear combination lights. *rm
NHTSA · bulletin constructeur10037655Années modèle 2011Affiché en anglais d’origine · traduction en attenteVoir le détail →
Sources : NHTSA (États-Unis, domaine public), Transports Canada (Licence du gouvernement ouvert – Canada), DVSA (Royaume-Uni, Open Government Licence v3.0), RappelConso et Safety Gate de l'UE (France, Licence Ouverte 2.0), MLIT (Japon, licence de données publiques 1.0) et MOLIT (Corée du Sud, car.go.kr).