Bulletin
Tire pressure monitoring system (TPMS) warning Light IlluminationMisure prevention logic
🔔 Créez un compte gratuit pour recevoir les alertes e-mail sur Mazda 2 (toutes les générations)
Les bulletins techniques (TSB) sont des instructions de réparation que les constructeurs envoient à leurs concessionnaires sur des problèmes connus. Ce ne sont pas des rappels de sécurité, mais ils confirment souvent un défaut.
Tire pressure monitoring system (TPMS) warning Light IlluminationMisure prevention logic
Some customers may experience a SBS/SCBS, LAS/LDWS and/or HBC warning light on. A system error message may also be found in the center display. DTC U3000:04-0A (Forward sensing camera (FSC) internal malfunction). DTC U3000:04-0A (Forward sensing camera (FSC) internal malfunction) is stored in the FSC module and cannot be erased. This concern may be caused by a hardware failure of an internal device of the FSC, which results in a malfunction detection. To eliminate this concern, the production process of the FSC has been modified.
Certains véhicules peuvent présenter un grincement provenant des freins avant lors du freinage après un stationnement prolongé par temps froid et humide. En raison d'une augmentation de la résistance des plaquettes par temps froid, les plaquettes vibrent facilement, ce qui provoque le bruit de grincement.
A/C blows warm air. Some customers may complain about warm air from the climate cointrol vents. This may be caused by improper brazing (A) of the evaporator (B) causing a refrigerant leak fr om the joint between the tubes and the header (D)
If you experience issues with the current version of ID's such as missing tools or modules not showing after completing a network test, be advised that we are aware of these issues and are working to resolve them. As a counter measure, it is advised that you un-install ids and re-install version 103.00 and "do not update" until further notice.
Some vehicles may exhibit an unusual noise from around the drivers foot area when repeatedly turning the steering wheel to the left or right. A vibration is felt at the steering wheel when the noise occurs. This concern may be caused by a lack of grease application to the splines of the intermediate shaft at the production line. The grease application process has been improved.
Certains clients peuvent se plaindre de l'un des points suivants : 1. L'écran du centre d'infodivertissement ne fournit pas le code d'autorisation (OTP) lors de l'inscription du véhicule connecté à l'application MyMazda. 2. Une ou plusieurs fonctions à distance sont inopérantes.
Certains véhicules peuvent présenter le voyant de contrôle moteur allumé avec le code DTC P0300:00 (Ratés d'allumage aléatoires détectés) enregistré. Cela peut être dû à une détection erronée de raté d'allumage causée par une logique de commande du PCM inadéquate. Pour éliminer ce problème, la logique de commande du PCM a été modifiée.
Certains clients peuvent remarquer que le voyant de charge s'allume pendant la conduite. Lors de l'inspection, le code DTC P2502:00 PCM (Dysfonctionnement de la tension générée par l'alternateur) est enregistré en mémoire. Cela peut être dû à une résistance entre la carte de circuit imprimé et la masse. Lorsqu'un courant électrique de forte intensité traverse le circuit, la position de la borne de masse peut ne pas être suffisamment efficace. Pour éliminer ce problème, le logiciel de commande du convertisseur CC/CC a été modifié. De plus, la procédure de production a été révisée. Le couple de serrage de la borne de masse et de la carte de circuit imprimé a été augmenté.
Some customers may experience a check engine light illumination at idle while stopped with DTC P0300:00 stored, resulting in rough idle conditions. P0300:00: Random misfire detected This concern is caused by improper engine control in the idle range. To eliminate the concern, the PCM control software has been modified.
Front/Rear stabilizer noise prevention
## MultiModel (équipé de skyactivdrive) : détérioration de la couleur de l'ATF La couleur neuve du liquide de transmission automatique (ATF) est bleue. À mesure que le kilométrage du véhicule augmente, la couleur de l'ATF évolue. Ce changement de couleur n'affecte pas les performances du véhicule.
BSM Radar aiming cannot be performed after rightside BSM control module rekkplacement
Mazda Technical Service Bulletins March 2016 Some vehicles may exhibit the inner cloth (A) falling down at the rear end causing a poor appearance and obstructing the view of the back window.
Maintenance.
MAZDA CONNECTED SERVICES - FOIRE AUX QUESTIONS (FAQ) : Index : Questions générales, Configuration et mise en route, Inscription / Enrôlement, Informations générales sur le Wi-Fi, Guide pratique Wi-Fi, Période d'essai Wi-Fi, Interaction avec l'application, Problèmes de service, Dépannage, Vérification du niveau de réception, Processus concessionnaire, Conditions dans lesquelles le démarrage à distance du moteur ne fonctionnera pas, Conditions dans lesquelles la fonction de démarrage à distance coupera le moteur, Vidéos pédagogiques, Ressources
MAZDA CONNECTED SERVICES - FOIRE AUX QUESTIONS (FAQ) : Index : Questions générales, Configuration et prise en main, Inscription / Enrôlement, Informations générales sur le Wi-Fi, Guide pratique du Wi-Fi, Période d'essai du Wi-Fi, Interaction avec l'application, Problèmes de service, Dépannage, Vérification du niveau de réception, Processus du concessionnaire, Conditions de non-fonctionnement du démarrage à distance, Conditions dans lesquelles la fonction de démarrage à distance coupe le moteur, Vidéos éducatives, Ressources
Some customers may experience the CHECK ENGINE light ON with DTC P0089:00 (Spill valve control solenoid valve control circuit range/performance problem) stored. This is caused by improper control software of the PCM detecting a false error, even with normal fuel pressure operation. To correct this issue, the control software of the PCM has been modified.
Some vehicles may experience a fuzzy appearance (tiny cracks) around the edge of the Active Driving Display. Replace the Active Driving Display.
Beginning with the CX-5 and Mazda6 models, grip type front and rear stabilizer bushings have been incorpo-rated for noise prevention purposes. If any type of grease or lubrication is applied to the bushings, it may create noise due to bushing slippage.
Some vehicles may experience the check engine light on with DTCs P2096:00, P2097:00 and/or P0524:00 that cannot be cleared by itself, and the check engine light stays on even if the detection condition has gone. P2096:00 - Air fuel too lean P2097:00 - Air fuel too rich P0524:00 - Engine oil pressure too low. This concern may be caused by improper PCM control logic. The PCM software has been modified to eliminate this concern.
Some vehicles may experience a fuzzy appearance (tiny cracks) around the edge of the Active Driving Display.
New IDs software version 102.00 and Update 102.01 is now available on MS3 IDs update 102.00 and 102.01 is now available on MS3 under the "IDs/Infotainment" tab.
Recall 0516j updated repair procedure
Windshield washer fluid change - Factory filled windshield washer fluid has been changed to an ethanol type (yellow color) instead of athe conventional methanol type (blue color). This change is for European compliance Mazda has decided to make the change for all markets.
Sources : NHTSA (États-Unis, domaine public), Transports Canada (Licence du gouvernement ouvert – Canada), DVSA (Royaume-Uni, Open Government Licence v3.0), RappelConso et Safety Gate de l'UE (France, Licence Ouverte 2.0), MLIT (Japon, licence de données publiques 1.0) et MOLIT (Corée du Sud, car.go.kr).