Lecture libre · compte gratuit pour contribuerSuccesseur d’Anticars (2000)

Mazda MX-30

2020– · 1 défauts documentés · 4 marchés

Les bulletins techniques (TSB) sont des instructions de réparation que les constructeurs envoient à leurs concessionnaires sur des problèmes connus. Ce ne sont pas des rappels de sécurité, mais ils confirment souvent un défaut.

Année modèle
BulletinModéréCarrosserieNA

Bulletin

DESCRIPTION Certains clients peuvent présenter un ou plusieurs des symptômes suivants, alors que le verrouillage et le déverrouillage des portières fonctionnent correctement avec la télécommande. Symptôme 1 : Le capteur tactile de la poignée extérieure de la portière avant ne verrouille pas les portières après la pluie et/ou un lavage de la voiture, bien que le déverrouillage soit possible. Symptôme 2 : Le capteur tactile de la poignée extérieure de la portière avant ne déverrouille pas les portières. Capteur tactile de la poignée extérieure de portière pour le verrouillage (1) / le déverrouillage (2) REMARQUE : Si le problème survient après une opération spécifique décrite ci-dessous, consultez le BT 09-046/22 (LE CAPTEUR TACTILE DE LA POIGNÉE EXTÉRIEURE DE PORTIÈRE NE VERROUILLE PAS ET NE DÉVERROUILLE PAS APRÈS UNE OPÉRATION SPÉCIFIQUE). 1. [MX-30] Après l'utilisation du préconditionnement de l'habitacle ou des feux de détresse pendant environ 15 minutes. 2. [MAZDA3 et CX-30] Après l'utilisation des feux de détresse pendant environ 15 minutes. 3. [MAZDA3, CX-30 et MX-30] Lorsque les deux capteurs tactiles sont touchés en même temps. Cause 1 (pour le symptôme 1) : De l'eau peut s'accumuler autour du capteur tactile de la poignée extérieure, ce qui réduit temporairement la sensibilité du capteur capacitif. De plus, si de la mousse de lavage pénètre dans la poignée extérieure pendant le lavage du véhicule, cette mousse peut perturber la détection du capteur tactile. Mazda travaille toujours sur une modification de production en série pour ce problème. Cause 2 (pour le symptôme 2) : Une soudure défectueuse lors du processus de fabrication peut perturber la détection du capteur tactile. Pour éliminer ce problème, le processus de fabrication a été modifié. Les clients présentant ce problème doivent faire réparer leur véhicule en suivant la procédure de réparation ci-dessous. PROCÉDURE DE RÉPARATION 1. Vérifier la plainte du client. 2. Réparer le véhicule selon le ou les symptômes constatés. Symptôme 1 : Suivre la « Procédure d'étanchéification d'un capteur tactile » ci-dessous pour rendre le capteur tactile étanche. Symptôme 2 : Remplacer la poignée extérieure avant par une poignée modifiée, en suivant les instructions sur MGSS. Mazda3 (DÉPOSE/POSE DE LA POIGNÉE EXTÉRIEURE AVANT) CX-30 (DÉPOSE/POSE DE LA POIGNÉE EXTÉRIEURE AVANT) MX-30 (DÉPOSE/POSE DE LA POIGNÉE EXTÉRIEURE AVANT) Si les deux symptômes sont constatés : Remplacer la poignée extérieure avant par une poignée modifiée et suivre la « Procédure d'étanchéification d'un capteur tactile » ci-dessous pour rendre le capteur tactile étanche. REMARQUE : NE PAS réparer l'autre poignée extérieure avant du véhicule si elle ne présente aucun problème. 3. Vérifier la réparation en contrôlant si la nouvelle poignée extérieure verrouille et déverrouille correctement la portière.

NHTSA · bulletin constructeur11030603Années modèle 2022Traduit automatiquement · original : anglaisVoir le détail →
BulletinModéréÉlectroniqueNA

Bulletin

Some customers may experience the master warning light and/or the "In-Vehicle Network Malfunction" warning message in the instrument cluster on with DTC B119F:01 (TCU - Tel antenna No. 1 malfunction) stored.

NHTSA · bulletin constructeur11003361Années modèle 2022Affiché en anglais d’origine · traduction en attenteVoir le détail →
BulletinModéréFreinsNA

Bulletin

Some customers may experience the following concerns: The liftgate or the trunk lid will not unlock even when the vehicle is parked and the ignition is off. If the engine is running (POWER ON) or the ignition is turned to on (READY ON), it will unlock. The auto close operation of the power liftgate is not performed (The liftgate can be closed manually). To eliminate this concern, the control software of the DSC HU/CM (or the electronically controlled brake unit) has been modified. Customers

NHTSA · bulletin constructeur11003356Années modèle 2023Affiché en anglais d’origine · traduction en attenteVoir le détail →
BulletinModéréFreinsNA

Bulletin

Some customers may experience that the liftgate or the trunk lid will not unlock even when the vehicle is parked and the ignition is off. If the engine is running (POWER ON) or the ignition is turned to on (READY ON), it will unlock. To eliminate this concern, the control software of the DSC HU/CM (or the electronically controlled brake unit) has been modified.

NHTSA · bulletin constructeur10254184Années modèle 2023Affiché en anglais d’origine · traduction en attenteVoir le détail →
BulletinModéréCarrosserieNA

Bulletin

Some customers may experience that, with a specific operation, the touch sensor of front door outer handle does not lock and unlock the doors but the remote transmitter operates correctly. Description of the specific operations: Specific Operation 1 [MX-30]: After using cabin preconditioning or hazard warning lights for approx.15 minutes. Specific Operation 2 [MAZDA3 and CX-30]: After using hazard warning lights for approx. 15 minutes. Specific Operation 3 [MAZDA3, CX-30 and MX-30]: When both touch sensors are touched at once. Specific Operation 1 and 2 Cause: The touch sensor has been disabled to avoid the unintended locking/unlocking operation caused by rain. Specific Operation 3 Cause: The control logic is not appropriate. NOTE: If the concern occurs without the specific operation above, refer to TSB 09-019/22 (DOOR OUTER HANDLE TOUCH SENSOR DOES NOT LOCK AND/OR UNLOCK). To correct this issue, the control software of the LF control unit (LFU) has been modified.

NHTSA · bulletin constructeur10252505Années modèle 2022Affiché en anglais d’origine · traduction en attenteVoir le détail →
BulletinModéréCarrosserieNA

Bulletin

Some customers may complain that oil leaks from the rear shock absorber. Due to the structure, a small amount of oil is leaked out, but there is no functional concern. However, this oil leak level is almost the same where shock absorber replacement is required. To eliminate this concern, the structure of the oil seal in the rear shock absorber has been modified

NHTSA · bulletin constructeur10244579Années modèle 2022Affiché en anglais d’origine · traduction en attenteVoir le détail →
BulletinModéréSuspensionNA

Bulletin

Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 7000C0A-NA02_11046). Ver. 7000C0A-NA02_11046 fixes these software errors (bugs): The system does not resume the play list after editing a play list for an USB audio device. The screen does not show proper picture when receiving SiriusXM data. Ver. 7000C0A-NA02_11044 fixes these software errors (bugs): Beep sounds every couple of minutes. Language setting may not be accepted correctly. When refusing the incoming call while playing audio tracks using the Apple CarPlay, the screen shows Phone in use message and it stops playing audio tracks. The audio track may not pause when pressing the mute button. The screen freezes when smartphone receives messages under Bluetooth connection. Ver. 7000C0A-NA02_11036 fixes these software errors (bugs): Screen freezes and goes to white screen, then the system reboots. Cannot control the audio system with steering switches and command switch. If another incoming call comes in immediately after the hands-free call is ended, the call is automatically accepted. Establishing Bluetooth connection takes tiime. DTC U3000:49 is stored which may be accompanied with following symptoms. -No sound comes out from the speakers. -Audio source selection is unavailable. The vehicle icon rotates when using the navigation with "head-up" mode.

NHTSA · bulletin constructeur10238677Années modèle 2022Affiché en anglais d’origine · traduction en attenteVoir le détail →
BulletinModéréAutreNA

Bulletin

Some customers may complain that Mazda Connect does not start (blank screen) or that it takes a long time to restart/ reboot after starting the vehicle. This is caused by the initialization process with the CMU failing at startup due to a defective circuit board element. To eliminate this concern, the internal hardware (DRAM) of the CMU has been improved.

NHTSA · bulletin constructeur10237206Années modèle 2022Affiché en anglais d’origine · traduction en attenteVoir le détail →
BulletinModéréCarrosserieNA

Bulletin

Some customers may complain that oil leaks from the rear shock absorber. Due to the structure, a small amount of oil is leaked out, but there is no functional concern. However, this oil leak level is almost the same where shock absorber replacement is required. To eliminate this concern, the structure of the oil seal in the rear shock absorber has been modified.

NHTSA · bulletin constructeur10233659Années modèle 2022Affiché en anglais d’origine · traduction en attenteVoir le détail →
BulletinModéréAutreNA

Bulletin

Some customers may complain that Mazda Connect does not start (blank screen) or that it takes a long time to restart/ reboot after starting the vehicle. This is caused by the initialization process with the CMU failing at startup due to a defective circuit board element. To eliminate this concern, the internal hardware (DRAM) of the CMU has been improved.

NHTSA · bulletin constructeur10233569Années modèle 2022Affiché en anglais d’origine · traduction en attenteVoir le détail →
BulletinModéréSuspensionNA

Bulletin

Some vehicles may exhibit a steering shimmy or body vibration during the PDI test drive or during the first few miles of driving after the vehicle has been delivered to the customer due to flat spots on the tires. Flat spots on tires may be caused by improper maintenance during dealer storage (e.g.: Vehicle was left stationary for a prolonged period of time in high ambient temperatures).

NHTSA · bulletin constructeur10232302Années modèle 2022Affiché en anglais d’origine · traduction en attenteVoir le détail →
BulletinModéréFreinsNA

Bulletin

Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.

NHTSA · bulletin constructeur10230875Années modèle 2022Affiché en anglais d’origine · traduction en attenteVoir le détail →
BulletinModéréAutreNA

Bulletin

Some customers may complain that Mazda Connect does not start (blank screen) or that it takes a long time to restart/ reboot after starting the vehicle. This is caused by the initialization process with the CMU failing at startup due to a defective circuit board element. To eliminate this concern, the internal hardware (DRAM) of the CMU has been improved.

NHTSA · bulletin constructeur10226898Années modèle 2022Affiché en anglais d’origine · traduction en attenteVoir le détail →
BulletinModéréCarrosserieNA

Bulletin

Some customers may experience that, with a specific operation, the touch sensor of front door outer handle does not lock and unlock the doors but the remote transmitter operates correctly. Description of the specific operations: - Specific Operation 1 [MX-30]: After using cabin preconditioning or hazard warning lights for approx.15 minutes. - Specific Operation 2 [MAZDA3 and CX-30]: After using hazard warning lights for approx. 15 minutes. - Specific Operation 3 [MAZDA3, CX-30 and MX-30]: When both touch sensors are touched at once. - Specific Operation 1 and 2 Cause: The touch sensor has been disabled to avoid the unintended locking/unlocking operation caused by rain. - Specific Operation 3 Cause: The control logic is not appropriate. To correct this issue, the control software of the LF control unit (LFU) has been modified.

NHTSA · bulletin constructeur10226892Années modèle 2022Affiché en anglais d’origine · traduction en attenteVoir le détail →
BulletinModéréFreinsNA

Bulletin

Some customers may complain about the following message displayed in the Multi-Information Display: In the following cases, the MRCC with Stop & Go function system is canceled when the vehicle is traveling at 19 mph (30 km/h) or less: * The Forward Sensing Camera (FSC) cannot detect target objects due to one of the following: - The windshield is dirty - The FSC lens is foggy - There is low visibility due to rain, fog or snow - It is at night and there is not enough light - There is direct or reflected sunlight on the FSC - There is problem with the FSC * There is a problem with the AUTOHOLD control function. * There is a problem with the electric parking brake (EPB).

NHTSA · bulletin constructeur10225763Années modèle 2022Affiché en anglais d’origine · traduction en attenteVoir le détail →
BulletinModéréSuspensionNA

Bulletin

The Blind Spot Monitoring (BSM) system can malfunction with the following symptoms if the rear side radar sensors are installed facing the wrong direction. - BSM system indicates vehicle on the opposite side. - i-ACTIVSENSE indicator ring will not turn green - Rear Cross Traffic Alert (RCTA) does not work - Rear side radar sensor

NHTSA · bulletin constructeur10222563Années modèle 2023Affiché en anglais d’origine · traduction en attenteVoir le détail →
BulletinModéréAutreNA

Bulletin

Certains clients peuvent se plaindre que Mazda Connect ne démarre pas ou qu'il met beaucoup de temps à redémarrer après le démarrage du véhicule. Cela est dû au processus d'initialisation de l'unité CMU qui échoue au démarrage en raison d'un élément défectueux sur la carte de circuit imprimé. Pour éliminer ce problème, le matériel interne de l'unité CMU a été amélioré.

NHTSA · bulletin constructeur10218768Années modèle 2022Traduit automatiquement · original : anglaisVoir le détail →
BulletinModéréFreinsNA

Bulletin

This information will give you the necessary knowledge to respond to customers concerns of Smart Brake Support (SBS) unintended braking. By educating the customer on the system operation, it should reduce their anxiety or distrust of the vehicle.

NHTSA · bulletin constructeur10218772Années modèle 2022Affiché en anglais d’origine · traduction en attenteVoir le détail →
BulletinModéréSuspensionNA

Bulletin

Some vehicles may exhibit a steering shimmy or body vibration during the PDI test drive or during the first few miles of driving after the vehicle has been delivered to the customer due to flat spots on the tires. Flat spots on tires may be caused by improper maintenance during dealer storage (e.g.: Vehicle was left stationary for a prolonged period of time in high ambient temperatures).

NHTSA · bulletin constructeur10213147Années modèle 2022Affiché en anglais d’origine · traduction en attenteVoir le détail →
BulletinModéréSuspensionNA

Bulletin

Some customers may complain that the steering wheel is off center more than 3 even when driving straight on a flat road.

NHTSA · bulletin constructeur10210902Années modèle 2022Affiché en anglais d’origine · traduction en attenteVoir le détail →
BulletinModéréSuspensionNA

Bulletin

Some customers may complain about the infotainment system and/or the MyMazda App showing incorrect tire pressures and/or tire pressure missing. This may be caused by: Incorrect calendar entry (month/day/year) after a battery disconnect *Infotainment system software update. *BCM TPMS unlearn during vehicle storage or transport. *Wheel/Tire change

NHTSA · bulletin constructeur10209755Années modèle 2022Affiché en anglais d’origine · traduction en attenteVoir le détail →
BulletinModéréSuspensionNA

Bulletin

Some customers may report concerns with interior upholstery surface stains particularly on high contact areas (e.g.: steering wheel, door panels, shifter...etc.). This may be caused by skin oils or chemicals such as hand lotions. Use a clean towel damped in leather/vinyl cleaner or mild soap to clean the steering wheel. NOTE: Upholstery maintenance and care information can also be found in the Owner's Manual.

NHTSA · bulletin constructeur10208554Années modèle 2022Affiché en anglais d’origine · traduction en attenteVoir le détail →
BulletinModéréÉlectroniqueNA

Bulletin

Some vehicle may experience the i-ACTIVSENSE/ALH warning lights on and a system error messages may be found in the center display as well. DTC U3000:04 (FSC) is stored in memory DTC U3000:04 (FSC) - Forward sensing camera (FSC) internal malfunction This may be caused by a hardware failure in an internal device of the FSC that results in the malfunction detection. To eliminate this concern, the production process of the FSC has been modified.

NHTSA · bulletin constructeur10206960Années modèle 2022Affiché en anglais d’origine · traduction en attenteVoir le détail →
BulletinModéréFreinsNA

Bulletin

Unexpected Smart Brake Support (SBS-R) Operation Wile Reversing: Some customers may complain about unexpected collision warning or automatic braking while reversing under certain conditions such as a step or object on the road behind the vehicle. This is caused by the control software of the parking assist unit of the Smart Brake Support (SBS-R) unintentionally detecting under certain conditions. To eliminate this concern, the control software of the parking assist unit has been modified. Customers having this concern should have their vehicle repaired using the following repair procedure.

NHTSA · bulletin constructeur10206010Années modèle 2022Affiché en anglais d’origine · traduction en attenteVoir le détail →
BulletinMineurÉlectroniqueNA

Bulletin

## DESCRIPTION Certains véhicules peuvent continuer d'afficher la notification de rappel « IMPORTANT NOTICE. VIEW VEHICLE STATUS MONITOR FOR DETAILS » sur l'écran central, même après l'achèvement du rappel. REMARQUE : une fois la demande de garantie relative à la campagne de rappel approuvée par Mazda Japon, la notification de rappel sera automatiquement supprimée via Connected Services le lendemain ou plus tard. Cette situation peut se produire si l'abonnement à Connected Services a été annulé alors que la notification de rappel était encore active. ## ACTION À ENTREPRENDRE Si vous rencontrez la situation décrite ci-dessus, utilisez MDARS pour supprimer manuellement la notification de rappel sur l'écran central. Remarque : MDARS ne peut supprimer la notification de rappel que lorsque MCVV n'indique aucun contrat CV.

NHTSA · bulletin constructeur11037008Années modèle 2023Traduit automatiquement · original : anglaisVoir le détail →
Plus anciens →

Sources : NHTSA (États-Unis, domaine public), Transports Canada (Licence du gouvernement ouvert – Canada), DVSA (Royaume-Uni, Open Government Licence v3.0), RappelConso et Safety Gate de l'UE (France, Licence Ouverte 2.0), MLIT (Japon, licence de données publiques 1.0) et MOLIT (Corée du Sud, car.go.kr).