Lettura libera · account gratuito per contribuireErede di Anticars (2000)

BMW Serie 3

1990–2000 · 16 difetti documentati · 6 mercati
Anno modello
RichiamoCriticoMotoreNA

Sistema di alimentazione

Su alcuni veicoli 318I, 318IC, 318IS, 325IC, 325IS, 325IX, 525I, 535I, 735I e 735IL, il tubo di alimentazione del carburante può indurirsi e "deformarsi" nel tempo a causa delle temperature del vano motore. Se si verifica questa "deformazione", è possibile che si verifichino trafilamenti tra il tubo e il raccordo, poiché la fascetta potrebbe non esercitare una forza di tenuta sufficiente a compensare l'indurimento del tubo. La fuoriuscita di carburante, in presenza di una fonte di accensione, potrebbe causare un incendio nel vano motore. Correzione: i tubi di alimentazione del carburante e le relative fascette saranno sostituiti con componenti di un nuovo modello.

Transport Canada30 mag 19941994096Anni modello 1990–1993Tradotto automaticamente · originale: ingleseVedi dettagli →
RichiamoCriticoMotoreNA

Sistema di alimentazione, benzina: Erogazione: Tubi flessibili, tubazioni e raccordi

Con il tempo, i tubi di alimentazione del carburante possono indurirsi e "fissarsi" in posizione, causando una perdita di carburante nel punto di collegamento tra il tubo e il raccordo del motore. La fascetta utilizzata per fissare il tubo al raccordo non è in grado di compensare l'indurimento del tubo di alimentazione del carburante.

NHTSA · Stati Uniti11 apr 199494V066000Anni modello 1990–1993Tradotto automaticamente · originale: ingleseVedi dettagli →
RichiamoModeratoMotoreNA

Engine and engine cooling:Cooling system

Vehicle description: Passenger vehicles. A malfunction or failure of a coolant system component, such as a thermostat, water pump, or fan belt, can result in significantly increased coolant temperature and system pressure. If the indications of a critical overheating condition is not noticed by the driver, it is possible that damage to, or failure of, a coolant system component could occur.

NHTSA · Stati Uniti4 ago 199898V178000Anni modello 1992–1995Mostrato in inglese originale · traduzione in attesaVedi dettagli →
RichiamoModeratoMotoreNA

Engine

On certain 318IC, 318IS, 318TI, 325I, 325IC, 325IS, 525I, 525IT, 530I, 530IT, 540I, 740I, 740IL, 840CI and M3, the cruise control and throttle cable are attached to the same throttle valve actuating lever at the throttle housing. It is possible that the plastic bushing on either cable could break causing the outer cable housing to separate from the bushing. Throttle pedal application without cruise control engagement could cause the outer tube to catch on the edge of the broken bushing resulting in the throttle valve remaining partially open. If this were to occur, the car might not decelerate as expected and a crash could occut. Correction: A spring clip will be installed on the outer tube of each cable to prevent dislodgment from the bushing.

Transport Canada9 ott 19971997173Anni modello 1992–1996Mostrato in inglese originale · traduzione in attesaVedi dettagli →
RichiamoModeratoMotoreNA

Vehicle speed control

The cruise control and throttle cables are attached to the same throttle valve actuating lever at the throttle housing. It is possible that the plastic bushing on either cable could break due to environmental influences coupled with vibration. If the bushing breaks, the outer cable housing can separate from the bushing. In this case, during application of the throttle pedal without cruise control being engaged, the outer tube could catch on the edge of the broken bushing.

NHTSA · Stati Uniti19 ago 199797V131000Anni modello 1992–1996Mostrato in inglese originale · traduzione in attesaVedi dettagli →
RichiamoModeratoMotoreNA

Engine

On certain 318I and 318IS vehicles, under certain conditions, with low ambient temperatures (-10 degrees and colder) and a warmed-up engine, water vapour in the warm air from the crankcase might condense and freeze in the throttle body. This could prevent the throttle plate from closing as the driver releases the gas pedal and might result in loss of vehicle control. Correction: Throttle body heater will be replaced with a modified heater.

Transport Canada12 lug 19941994115Anni modello 1992–1994Mostrato in inglese originale · traduzione in attesaVedi dettagli →
RichiamoModeratoMotoreNA

Fuel system, gasoline:Fuel injection system

The adhesive material of the two piece throttle body heater migrates into the circulation chamber causing build up of impurities and restriction of flow within the chamber. This condition and water vapors from the crank that freezes at low ambient air temperatures prevents the throttle plate from closing as the driver releases the gas pedal, causing loss of throttle control.

NHTSA · Stati Uniti17 feb 199494V037000Anni modello 1992–1994Mostrato in inglese originale · traduzione in attesaVedi dettagli →
RichiamoModeratoMotoreNA

Heater And Defroster

On certain 318I, 325I and M3 vehicles, elevated pressure in the cooling system due to overheating could result in cracking of the heater core end piece. Should this happen, coolant could be expelled onto the lower right leg of the driver, possibly resulting in personal injury and/or fogging of the interior surfaces of the windows causing reduced driver vision. Correction: A thermistatic bypass valve will be installed to control coolant temperature in the heater core. Also, a new design radiator cap will be installed to control pressure and provide greater overflow.

Transport Canada19 lug 19931993100Anni modello 1990–1993Mostrato in inglese originale · traduzione in attesaVedi dettagli →
RichiamoModeratoMotoreNA

Vehicle speed control

The crankcase ventilation system, vented into the intake tract of the engine at the bellows boot ahead of the throttle housing, allows warm water vapor from the crankcase vent to condense and freeze in the colder bellows boot when the ambient air temperature is 15 degrees fahrenheit or less. The build up of ice can dislodge and move into the throttle housing, preventing the throttle plate from fully closing when the driver releases the gas pedal.

NHTSA · Stati Uniti17 dic 199191V219000Anni modello 1991–1992Mostrato in inglese originale · traduzione in attesaVedi dettagli →
RichiamoModeratoMotoreNA

Engine

On certain 318I, 318IC and 318IS vehicles, at temperatures below -10 degrees centigrade with the engine partially or completely warmed up, condensation from the crankcase ventilation system may freeze at the throttle housing and prevent the throttle plate from fully closing when the accelerator pedal is released. This could result in a slow rate of deceloeration from speed or increased idle speed both of which may adversely affect vehicle control. Correction: Throttle house will be replaced with a version containing a modified heating system and the crankcase vent will be rerouted.

Transport Canada4 dic 19911991163Anni modello 1991–1992Mostrato in inglese originale · traduzione in attesaVedi dettagli →

Fonti: NHTSA (Stati Uniti, pubblico dominio), Transport Canada (Open Government Licence – Canada), DVSA (Regno Unito, Open Government Licence v3.0), RappelConso e Safety Gate UE (Francia, Licence Ouverte 2.0), MLIT (Giappone, Public Data License 1.0) e MOLIT (Corea del Sud, car.go.kr).