Bollettino
Programma di richiamo 26H02: alcuni veicoli Mustang, Fusion ed Edge di modello 2015. Sostituzione del modulo airbag lato guidatore
🔔 Crea un account gratuito per ricevere avvisi via e-mail su Ford Edge (tutte le generazioni)
I bollettini tecnici (TSB) sono istruzioni di riparazione che i costruttori inviano ai concessionari su problemi noti. Non sono richiami di sicurezza, ma spesso confermano un difetto.
Programma di richiamo 26H02: alcuni veicoli Mustang, Fusion ed Edge di modello 2015. Sostituzione del modulo airbag lato guidatore
This bulletin supersedes 23-2028. Reason for updates: increase the labor time allowance to account for axle removal. Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: - Fuel tank not filling up beyond half full - Small amount of fuel leaking from vapor line connection - Stalling after start - Hard to start/extended crank
*This article supersedes TSB 24-2199 to add the rear half shaft seals to the TSB parts list. Some of the vehicles listed in the model statement above may exhibit one of the following conditions: *Fuel tank not filling up beyond half-full *Hard to start *Stalls upon restart after refueling *A malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P04F0, P0451, P0455, and/or P0496 may also be stored in the powertrain control module (PCM) This may be due to a disconnected fuel vapor line inside the fuel tank. Additional Model Information: All Wheel Drive (AWD).
Some 2024 Edge and 2023 Nautilus vehicles built on 28-Aug-2023 and through 02-Apr-2024 equipped with a 2.0L EcoBoost engine may experience an illuminated malfunction indicator (MIL) with diagnostic trouble codes (DTCs) P0401 or P2457. Various engine cooling system symptoms which may include an internal/external leak, white smoke from the tailpipe, and/or over-temperature warnings may also be present. This may be due to a transmission fluid heater coolant control valve restricting flow and possibly causing the exhaust gas recirculation (EGR) cooler to crack. To correct the condition, follow the Service Procedure to replace the affected parts.
Some 2024 Edge vehicles equipped with a 2.0L engine and all-wheel drive (AWD) may experience the fuel tank not filling up beyond half-full, hard to start, and/or stalls upon restart after refueling. A malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P04F0, P0451, P0455, and/or P0496 may also be stored in the powertrain control module (PCM). This may be due to a disconnected fuel vapor line inside the fuel tank. To correct the condition, follow the Service Procedure to reattach the fuel tank vapor line inside the fuel tank.
Some 2022 Edge/Nautilus vehicles built on 18-Jul-2022 and through 04-Aug-2022 equipped with all-wheel drive (AWD) and a 2.0L engine may experience the fuel tank not filling up beyond half full, small amount of fuel leaking from the vapor line connection, vehicle hard to start, and/or vehicle stalling after start. This may be due to a disconnected fuel vapor line inside the fuel tank. To correct the condition, follow the Service Procedure to reattach the fuel tank vapor line inside the fuel tank.
Some 2021 Edge vehicles which have received an APIM software update may experience a concern with Sirius radio being inoperative. This will be accompanied by ACM diagnostic trouble code (DTC) B1A89:13 for the satellite antenna. To correct this condition, download and run the APIM Programmable Module Installation (PMI) application using the latest software level of the Ford Diagnosis and Repair System (FDRS). When the PMI asks, Is The Original Module Installed?, select NO. When the PMI completes, perform an ALL CMDTC test and clear all DTCs. For claiming, use causal part 14G670 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Some 2021 Mustang Mach-E/F-150/Edge/Nautilus vehicles equipped with SYNC Gen 4 may experience a USB Error 0 being displayed in the infotainment screen during Programmable Module Installation (PMI) on the replacement accessory protocol interface module (APIM) ordered on 01-Jan-2022 and through 13-Apr-2022. This maybe due to a software issue with the replacement APIM. Order another APIM from Ford Component Sales (FCS). Service stock has been corrected.
Some 2022 Ford and Lincoln vehicles may need to perform A/C leak detection diagnostics. The 2022 Workshop Manual (WSM), Section 412-00 for A/C leak detection diagnosis is incomplete and is in the process of being updated. At this time, Pinpoint Test AN of Section 412-00 in the 2022 F-150 WSM can be used temporarily for the service procedure and specifications. Use the correct vehicle specific removal and replacement sections as needed. A new labor operation 19700A45 has also been released to align with the new procedure.
Alcuni veicoli Ford e Lincoln del 2016-2017 con un nuovo modulo di controllo della carrozzeria (BCM) installato possono presentare un errore di programmazione quando si utilizzano le versioni IDS da 122.03 a 123.01, con i messaggi "Data Corrupt" o "Configuration Failed, would you like to retry?". Lo strumento di diagnosi IDS versione 123.02 contiene una correzione per questo errore di programmazione. Installare IDS versione 123.02 o successiva da PTS > scheda Rotunda > Diagnostic Tool Support > Download Software. Una volta installato, eseguire l'installazione del modulo programmabile BCM (PMI). Consultare il Manuale di officina (WSM), Sezione 419-10 > Rimozione e installazione.
Some 2021 Mustang Mach-E, F-150, and Edge vehicles may experience a GWM and/or TCU programming failure with an error message displayed in the Ford Diagnosis and Repair System (FDRS) stating The Programming Or Part Number Validation Process Has Failed. This may be due to the USB flash drive being removed from the vehicle media hub before fully completing reprogramming. Reprogram the module(s) following the vehicle onscreen prompts. After the ignition cycle during reprogramming, the touchscreen may go blank. This is a normal part of the reprogramming process. Leave the USB flash drive installed in the media hub until the touchscreen displays Update Successful.
Alcuni veicoli Ford e Lincoln del 2016-2017 con un nuovo Body Control Module (BCM) installato possono presentare un errore di programmazione utilizzando IDS v122.03 e versioni successive, con la dicitura "Data Corrupt" o Configuration Failed, would you like to retry?. È stata rilasciata una soluzione temporanea per completare il processo di programmazione del BCM. Disinstallare IDS dal computer. Eseguire lo strumento di pulizia IDS situato in PTS > scheda Rotunda > Diagnostic Tool Support > IDS Support > IDS troubleshooting guide. Installare IDS v122.01 (122_FULL) copiando il seguente link in una barra degli indirizzi del browser https://www.fordservicecontent.com/Ford_Content/IDS/SoftwareUpdates/IDS-122.01_full.exe. Ripetere la Programmable Module Installation (PMI) del BCM utilizzando IDS livello 122.01. Monitorare OASIS per eventuali aggiornamenti.
Some 2021 Mustang Mach-E, F-150, Edge/Nautilus or Bronco vehicles equipped with SYNC 4 may have a customer symptom of the SYNC voice commands being activated without pushing the steering wheel switch. This may be due to the feature called Wake Word within SYNC 4. This feature allows the driver to activate the SYNC 4 system without pushing the steering wheel switch. Under the touchscreen Settings > Voice Settings the preferred Wake Word can be changed. The feature can also be disabled if the customer does not want the SYNC voice commands being activated without touching the steering wheel switch. This feature is not a defect. Do not submit a claim for this condition.
Some 2021 Mustang Mach-E, Edge and Nautilus customers may be unable to authorize the FordPass/LincolnWay app and the Enable Connected Services prompt is not showing in the SYNC screen with no diagnostic trouble codes (DTC) present in the telematics control unit (TCU) or the gateway module A (GWM). To resolve this condition, remove the TCU fuse for 5 minutes then reinstall. If available, update the TCU to the latest software level using the latest version of FDRS and try to authorize the vehicle to the app. If the concern is still present, remove the GWM fuse for 5 minutes and reinstall. If the concern is still present, follow normal diagnostics in Workshop Manual (WSM), Section 415-00.
Some 2017-2018 MKX and 2018 Edge vehicles may exhibit an inoperative liftgate after rear gate trunk module (RGTM) reprogramming or programmable module installation (PMI) process. This may be due to the software in the RGTM. To correct the condition, reprogram the RGTM using the latest software level of the appropriate Ford diagnostic scan tool. For claiming use causal part number 14B291 and Section 10 of the Service Labor Time Standards (SLTS) Manual.
Some 2021 Mustang Mach-E/F-150/Edge/Nautilus vehicles may require a reboot of the SYNC 4 system. For vehicles equipped with a volume/power and right seek button, press and hold both the volume/power and right seek button for 10 seconds and the system will reboot. For vehicles not equipped with a volume/power button, holding the seek right and volume down buttons on the steering wheel controls will reboot the SYNC 4 system. The Workshop Manual (WSM) is in the process of being updated with this procedure.
Some 2021 Mustang Mach-E/F-150/Edge/Nautilus vehicles may require a reboot of the SYNC 4 system. For vehicles equipped with a volume/power and seek buttons, press and hold both the volume/power and seek buttons for 10 seconds and the system will reboot. For vehicles not equipped with a volume/power button, holding the seek right and volume down buttons on the steering wheel controls will reboot the SYNC 4 system. The Workshop Manual (WSM) is in the process of being updated with this procedure.
Some 2020 Edge/Nautilus/Escape/Corsair/Transit Connect vehicles with and 8F35/8F40 transmission built on or before 30-Sep-2020 may exhibit an illuminated powertrain malfunction (wrench) indicator with diagnostic trouble codes (DTCs) P0741 and/or P1744 present or stored in the powertrain control module (PCM). This may be due to the torque converter and a pump stator bushing leak. Replacement of only the torque converter and/or the main control may not resolve the concern. To correct the condition, replace the following components: the torque converter, fluid pump assembly, both fluid filters, main control, input shaft, and flush the transmission cooling system.
Some 2017-2020 Ford and Lincoln vehicles equipped with a TCU may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app , incomplete user authorization and/or no modem electronic serial number (ESN) displayed. To correct this condition prior to programming, remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 48618 - 2020 Various Vehicles - Equipped With SYNC 3 - Unable To Schedule Remote Start Using Fordpass Or Lincolnway Applications Some 2020 Ford and Lincoln vehicles may exhibit a symptom of no ability to schedule a remote start event using the FordPass or Lincolnway app. If only the scheduling portion of the remote start system is missing from the mobile app or not functioning, please ensure the customer has installed the latest version of the Ford Pass or Lincoln Way app from the mobile phones app store. The customer may also need to log out of the Ford Pass or Lincoln Way app, and then log back in. If the remote start system is not functioning using the key fob and/or the on-demand remote start function from Ford Pass or Lincoln Way application, refer to Workshop Manual (WSM), Section 303-06 for further diagnosis.
SSM 48558 - 2017-2020 Various Vehicles Equipped With Telematics Control Unit (TCU) - Various FordPass/LincolnWay Mobile App Concerns Some 2017-2020 Ford and Lincoln vehicles equipped with a TCU may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization and/or no modem electronic serial number (ESN) displayed. To correct this condition prior to programming, remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
Some 2017-2020 Ford and Lincoln vehicles equipped with a TCU may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization and/or no modem electronic serial number (ESN) displayed. To correct this condition prior to programming, remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229.
Some 2017-2020 Ford and Lincoln vehicles equipped with a TCU may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization and/or accessory protocol interface module (APIM) DTC U0198 or no modem electronic serial number (ESN) displayed. To correct this condition prior to programming, remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229.
Some 2019 Mustang, Continental, Fusion, MKZ, F150, Transit Connect, Ranger, Edge or Nautilus with SYNC 3 may have the following intermittent symptoms: a solid blue screen when moving forward at speeds above 16 kph (10 mph), the rear view camera remains on the screen at speeds below 16 kph (10 mph), or inoperative infotainment applications. This may be due to the SYNC 3 software version installed on the vehicle. To correct the condition, follow the Service Procedure steps to reprogram the accessory protocol interface module (APIM).
Some 2018-2019 F-150 vehicles built on 23-Sep-2018 and through 28-Mar-2019 and 2019 Edge/Nautilus/Continental/MKZ vehicles built on 4-Dec-2018 and through 29-Mar-2019 and Fusion vehicles built on 16-Jan-2019 and through 12-Apr-2019 equipped with a 2.7L/3.0L EcoBoost engine may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P04DB stored in the powertrain control module (PCM). This may be due to the incorrect positive crankcase ventilation (PCV) valve installed. If the PCV valve is brown in color, refer to the Powertrain Control/Emissions Diagnosis (PC/ED) Manual for normal diagnostics. If the PCV valve is gray in color, replace the PCV valve, clear the DTC, and retest. If the DTC returns, refer to the PC/ED for normal diagnostics.
Fonti: NHTSA (Stati Uniti, pubblico dominio), Transport Canada (Open Government Licence – Canada), DVSA (Regno Unito, Open Government Licence v3.0), RappelConso e Safety Gate UE (Francia, Licence Ouverte 2.0), MLIT (Giappone, Public Data License 1.0) e MOLIT (Corea del Sud, car.go.kr).