技術通報
No Crank/No Start, Dead Battery Due to Parasitic Drain/Discharge.
🔔 無料アカウントを作成して Chevrolet ボルト (すべての世代) のメール通知を受け取る
技術サービス通報(TSB)は、既知の不具合についてメーカーが販売店に送る修理指示です。安全リコールではありませんが、不具合の裏付けになることがよくあります。
No Crank/No Start, Dead Battery Due to Parasitic Drain/Discharge.
17459 - Service Update. Certain vehicles may have a wireless charging pad that is inoperative. The customer will be unable to charge their cell phone with a wireless charger. Dealers are to check for a missing fuse. Install a new fuse and check the wireless charger pad operation
This Preliminary Information communication provides information to the technician about vehicles that may have misfires or rough running on cold start up. Technician may find a Diagnostic Trouble Code P0300. Technician will need to use a scan tool and observe Crankshaft Position Re-sync Counter parameter. The Re-sync Counter parameter should remain at 0 during all operating conditions, and while manipulating the related harnesses and connectors between the crankshaft position sensor and the Engine Control Module. Technician will need to inspect for water intrusion in related connectors, terminals, and components. Tech will need to bring the vehicle up to engine coolant temperature that was stored when Diagnostic Trouble Code P0300 was set. After the engine coolant temperature is up to temperature technician will need to perform compression and cylinder leakage and record the readings. Technician should also verify correct fuel system pressure, inspect the heated oxygen sensors for contamination from fuel, silicon, or the incorrect use of room temperature vulcanization silicone sealant, and inspect the spark plugs for incorrect heat range, coolant or oil fouling, carbon tracking, cracks or insulator fractures at the tip. Technician should also Test for coolant contamination into the cylinders.
This Preliminary Information communication provides information to the technician about vehicles that have the high voltage battery the tabs on X3 could become damaged during service. Technician will need to ensure to use caution when removing and installing this connector. Connectors need to be square to each other before the cam lock is engaged.
This Preliminary Information communication provides information to the technician about vehicles that have a no start or multiple messages on the Driver Information Center during cold weather. Technician will need to check the Vehicle Communication Interface Module label for Assembled in China. If the date is between 7/18/2014 and 8/3/2014, record the Station Identifier from the label and call General Motors Technical Assistance Center referencing this Preliminary Information for further assistance.
This Preliminary Information communication provides information to the technician about vehicles that may have misfires or rough running on cold start up. Technician may find a Diagnostic Trouble Code P0300. Technician will need to use a scan tool and observe Crankshaft Position Re-sync Counter parameter. The Re-sync Counter parameter should remain at 0 during all operating conditions, and while manipulating the related harnesses and connectors between the crankshaft position sensor and the Engine Control Module. Technician will need to inspect for water intrusion in related connectors, terminals, and components. Tech will need to bring the vehicle up to engine coolant temperature that was stored when Diagnostic Trouble Code P0300 was set. After the engine coolant temperature is up to temperature technician will need to perform compression and cylinder leakage and record the readings. Technician should also verify correct fuel system pressure, inspect the heated oxygen sensors for contamination from fuel, silicon, or the incorrect use of room temperature vulcanization silicone sealant, and inspect the spark plugs for incorrect heat range, coolant or oil fouling, carbon tracking, cracks or insulator fractures at the tip. Technician should also Test for coolant contamination into the cylinders.
This Preliminary Information communication provides information to the technician about vehicles that may have misfires or rough running on cold start up. Technician may find a Diagnostic Trouble Code P0300. Technician will need to use a scan tool and observe Crankshaft Position Re-sync Counter parameter. The Re-sync Counter parameter should remain at 0 during all operating conditions, and while manipulating the related harnesses and connectors between the crankshaft position sensor and the Engine Control Module. Technician will need to inspect for water intrusion in related connectors, terminals, and components. Tech will need to bring the vehicle up to engine coolant temperature that was stored when Diagnostic Trouble Code P0300 was set. After the engine coolant temperature is up to temperature technician will need to perform compression and cylinder leakage and record the readings. Technician should also verify correct fuel system pressure, inspect the heated oxygen sensors for contamination from fuel, silicon, or the incorrect use of room temperature vulcanization silicone sealant, and inspect the spark plugs for incorrect heat range, coolant or oil fouling, carbon tracking, cracks or insulator fractures at the tip. Technician should also Test for coolant contamination into the cylinders.
Chevrolet: On certain vehicles, after updated calibrations were installed, may exhibit a possible and an estimated electric range drop. *pe updated 12/7/11. *pe
この予備情報は、DTCがない状態でテレマティクスモジュールのGPS不具合を診断する方法について、現場に伝えるものです。
この予備情報は、DTC(故障診断コード)が記録されていない状態で、テレマティクスモジュールに関するGPSの不具合を現場でどのように診断するかについて伝えるものです。
This Preliminary information communicates to the field on how to diagnosis a GPS issue with the Telematic module with no DTC's
This Preliminary information communicates to the field on how to diagnosis a GPS issue with the Telematic module with no DTC's
この技術情報(サービスブレティン)は、VBMがリアカメラ機能を制御するため、リアカメラのガイドラインが表示されない場合があることをお客様にお知らせするものです。
Service Update for Inventory and Customer Vehicles Connected Navigation Radio Voice Command Not Working Expires with Base Warranty
Service Update for Inventory and Customer Vehicles Connected Navigation Radio Voice Command Not Working Expires with Base Warranty - Eqluipped with Connected Navigation Radio (UHQ)
This service bulletin provides information to the customer about the rear camera guidelines not being present at times due to the VBM taking over the rear camera option.
このインフォメーション・ブレティンは、VBM(車両ボディ管理モジュール)がリアカメラ機能を引き継ぐことにより、リアカメラのガイドラインが時折表示されない場合があることをお客様にお知らせするものです。
This service bulletin provides repair information to correct a customer concern that Radio is Theft Locked.
This service bulletin provides repair information to correct a customer concern of Radio Resets or Reboots and May Display myBrand Splash Animation.
Emissions Recall. General Motors has decided to conduct a Voluntary Emission Recall involving certain vehicles, equipped with 4-cylinder engines (RPO LHN, LEX, L3A, LYX, LKN, LE2, LCV or LTG). On some vehicles, an electrical connection in the circuit board may fail in the engine control module. If this occurs, a malfunction indicator lamp (MIL), such as the Check Engine Light may illuminate. Replace the Engine Control Module (ECM).
Emissions Recall. General Motors has decided to conduct a Voluntary Emission Recall involving certain vehicles, equipped with 4-cylinder engines (RPO LHN, LEX, L3A, LYX, LKN, LE2, LCV or LTG). On some vehicles, an electrical connection in the circuit board may fail in the engine control module. If this occurs, a malfunction indicator lamp (MIL), such as the Check Engine Light may illuminate. Replace the Engine Control Module (ECM).
This service bulletin provides repair information to correct a customer concern of software issues with Radio Software Version V808.
This Preliminary information communicates a concern where the radio will reboot when adjusting the volume intermittently and that engineering is investigating.
This Preliminary information communicates a concern where the radio will reboot when adjusting the volume intermittently and that engineering is investigating.
Malfunction Indicator Lamp (MIL) On, Possible P0300, P040B, P041B, P1427 and/or P1429 DTCs Set Some customers may comment on a check engine light illuminated. During diagnosis a technician may find one or more of the following DTCs set: P0300 Engine Misfire Detected P040B Exhaust Gas Recirculation Temperature Sensor 2 Circuit Range/Performance P041B Exhaust Gas Recirculation Temperature Sensor 1 Circuit Range/Performance P1427 EGR Temperature Sensor 1 Intake Air Temperature 1 Not Plausible P1429 EGR Temperature Sensor 2 Intake Air Temperature 1 Not Plausible This may be caused by a calibration within the K20 Engine Control Module
出典:NHTSA(米国、パブリックドメイン)、カナダ運輸省(Open Government Licence – Canada)、DVSA(英国、Open Government Licence v3.0)、RappelConso および EU Safety Gate(フランス、Licence Ouverte 2.0)、国土交通省(日本、公共データ利用規約1.0)、韓国国土交通部(car.go.kr)。