閲覧無料 · 投稿は無料アカウントでAnticars(2000年)の後継

Chevrolet ボルト

2010–2019 · 不具合12件 · 3市場

技術サービス通報(TSB)は、既知の不具合についてメーカーが販売店に送る修理指示です。安全リコールではありませんが、不具合の裏付けになることがよくあります。

技術通報中程度ブレーキNA

技術通報

Service Update for Inventory and Customer Erroneous Electric Park Brake Message and Light, DTC C027D Expires with Base Warranty

NHTSA · メーカー通報10246661モデルイヤー 2012原文(英語)で表示中 · 翻訳待ち詳細を見る →
技術通報中程度ブレーキNA

技術通報

FMVSS不適合リコール - ABS、横滑り防止装置、またはトラクションコントロール作動時に前輪ブレーキがロックする

NHTSA · メーカー通報10246757モデルイヤー 2012自動翻訳 · 原文:英語詳細を見る →
技術通報中程度電装NA

技術通報

No Crank/No Start, Dead Battery Due to Parasitic Drain/Discharge.

NHTSA · メーカー通報10254206モデルイヤー 2011原文(英語)で表示中 · 翻訳待ち詳細を見る →
技術通報中程度内装NA

技術通報

This informational bulletin provides information regarding the Passenger Presence System (PPS) May Command Seat Belt Reminder Chime and Passenger Airbag Indicator On When Electronic Devices or Conductive Objects are Placed on Front Passenger Seat

NHTSA · メーカー通報10138552モデルイヤー 2013原文(英語)で表示中 · 翻訳待ち詳細を見る →
技術通報中程度ブレーキNA

技術通報

12266 - Service Update. During vehicle startup, the Electric Park Brake telltale and the Service Electric Parking Brake telltale may illuminate in error. Dealers are to reprogram the Electronic Parking Bracke Control Module.

NHTSA · メーカー通報10138228モデルイヤー 2013原文(英語)で表示中 · 翻訳待ち詳細を見る →
技術通報中程度電装NA

技術通報

This Preliminary Information communication provides information to the technician about vehicles that may have misfires or rough running on cold start up. Technician may find a Diagnostic Trouble Code P0300. Technician will need to use a scan tool and observe Crankshaft Position Re-sync Counter parameter. The Re-sync Counter parameter should remain at 0 during all operating conditions, and while manipulating the related harnesses and connectors between the crankshaft position sensor and the Engine Control Module. Technician will need to inspect for water intrusion in related connectors, terminals, and components. Tech will need to bring the vehicle up to engine coolant temperature that was stored when Diagnostic Trouble Code P0300 was set. After the engine coolant temperature is up to temperature technician will need to perform compression and cylinder leakage and record the readings. Technician should also verify correct fuel system pressure, inspect the heated oxygen sensors for contamination from fuel, silicon, or the incorrect use of room temperature vulcanization silicone sealant, and inspect the spark plugs for incorrect heat range, coolant or oil fouling, carbon tracking, cracks or insulator fractures at the tip. Technician should also Test for coolant contamination into the cylinders.

NHTSA · メーカー通報10129886モデルイヤー 2012原文(英語)で表示中 · 翻訳待ち詳細を見る →
技術通報中程度サスペンションNA

技術通報

This preliminary bulletin provides a procedure to reprogram the power steering module to correct the customers concern of the MIL on and a drop in power steering assist.

NHTSA · メーカー通報10126211モデルイヤー 2012原文(英語)で表示中 · 翻訳待ち詳細を見る →
技術通報中程度サスペンションNA

技術通報

This preliminary informational bulletin provides a procedure to reprogram the electronic power steering control module for comments regarding a indicator lamp illuminated and DTC C0544 and U0415 set.

NHTSA · メーカー通報10126172モデルイヤー 2012原文(英語)で表示中 · 翻訳待ち詳細を見る →
技術通報中程度内装NA

技術通報

This informational bulletin provides information regarding the Passenger Presence System (PPS) May Command Seat Belt Reminder Chime and Passenger Airbag Indicator On When Electronic Devices or Conductive Objects are Placed on Front Passenger Seat

NHTSA · メーカー通報10113824モデルイヤー 2013原文(英語)で表示中 · 翻訳待ち詳細を見る →
技術通報中程度電装NA

技術通報

This Preliminary Information communication provides information to the technician about vehicles that may have misfires or rough running on cold start up. Technician may find a Diagnostic Trouble Code P0300. Technician will need to use a scan tool and observe Crankshaft Position Re-sync Counter parameter. The Re-sync Counter parameter should remain at 0 during all operating conditions, and while manipulating the related harnesses and connectors between the crankshaft position sensor and the Engine Control Module. Technician will need to inspect for water intrusion in related connectors, terminals, and components. Tech will need to bring the vehicle up to engine coolant temperature that was stored when Diagnostic Trouble Code P0300 was set. After the engine coolant temperature is up to temperature technician will need to perform compression and cylinder leakage and record the readings. Technician should also verify correct fuel system pressure, inspect the heated oxygen sensors for contamination from fuel, silicon, or the incorrect use of room temperature vulcanization silicone sealant, and inspect the spark plugs for incorrect heat range, coolant or oil fouling, carbon tracking, cracks or insulator fractures at the tip. Technician should also Test for coolant contamination into the cylinders.

NHTSA · メーカー通報10113340モデルイヤー 2012原文(英語)で表示中 · 翻訳待ち詳細を見る →
技術通報中程度電装NA

技術通報

This Preliminary Information communication provides information to the technician about vehicles that may have misfires or rough running on cold start up. Technician may find a Diagnostic Trouble Code P0300. Technician will need to use a scan tool and observe Crankshaft Position Re-sync Counter parameter. The Re-sync Counter parameter should remain at 0 during all operating conditions, and while manipulating the related harnesses and connectors between the crankshaft position sensor and the Engine Control Module. Technician will need to inspect for water intrusion in related connectors, terminals, and components. Tech will need to bring the vehicle up to engine coolant temperature that was stored when Diagnostic Trouble Code P0300 was set. After the engine coolant temperature is up to temperature technician will need to perform compression and cylinder leakage and record the readings. Technician should also verify correct fuel system pressure, inspect the heated oxygen sensors for contamination from fuel, silicon, or the incorrect use of room temperature vulcanization silicone sealant, and inspect the spark plugs for incorrect heat range, coolant or oil fouling, carbon tracking, cracks or insulator fractures at the tip. Technician should also Test for coolant contamination into the cylinders.

NHTSA · メーカー通報10112076モデルイヤー 2012原文(英語)で表示中 · 翻訳待ち詳細を見る →
技術通報中程度トランスミッションNA

技術通報

12241 - customer satisfaction program. Vehicles can be affected by incorrect calendar date information sent through the telematics systems. If a significantly incorrect date is received (for example, 00/00/0000), and the vehicle is in the "delayed rate and departure time" charging mode, the hybrid powertrain control module (hpcm2) may reset and open the propulsion power relays. As a result, the electric motor has temporarily stopped working due to this software anomaly when their vehicle is in the delayed time and rate charge mode.

NHTSA · メーカー通報10089702モデルイヤー 2013原文(英語)で表示中 · 翻訳待ち詳細を見る →
技術通報中程度内装NA

技術通報

15642 - special coverage. On some 2011 model year chevrolet volt vehicles, the airbag indicator may illuminate. This may be caused by the sensing and diagnostic module (sdm) monitoring an increase in the resistance of the driver or passenger side-impact airbag deployment loop circuits. This increased resistance may be caused by loose terminal crimps in either the driver or passenger seat mounted side-impact airbag wiring harness connectors. Dealers are to inspect for the presence of specific diagnostic trouble codes (dtcs) and, if necessary, bypass the harness connectors and repair wiring in the driver and/or passenger front side-impact airbag deployment loop circuits. The repairs will be made at no charge to the customer.

NHTSA · メーカー通報10089494モデルイヤー 2011原文(英語)で表示中 · 翻訳待ち詳細を見る →
技術通報中程度内装NA

技術通報

15642 - special coverage. On some 2011 model year chevrolet volt vehicles, the airbag indicator may illuminate. This may be caused by the sensing and diagnostic module (sdm) monitoring an increase in the resistance of the driver or passenger side-impact airbag deployment loop circuits. This increased resistance may be caused by loose terminal crimps in either the driver or passenger seat mounted side-impact airbag wiring harness connectors. Dealers are to inspect for the presence of specific diagnostic trouble codes (dtcs) and, if necessary, bypass the harness connectors and repair wiring in the driver and/or passenger front side-impact airbag deployment loop circuits. The repairs will be made at no charge to the customer.

NHTSA · メーカー通報10089435モデルイヤー 2011原文(英語)で表示中 · 翻訳待ち詳細を見る →
技術通報中程度内装NA

技術通報

Special Coverage Adjustment - Side Impact Airbag Connectors

NHTSA · メーカー通報10247256モデルイヤー 2011原文(英語)で表示中 · 翻訳待ち詳細を見る →
技術通報中程度内装NA

技術通報

Passenger Presence System (PPS) May Command Seat Belt Reminder Chime Passenger Airbag Indicator On When Electronic Devices or Conductive Objects are Placed on Front Passenger Seat

NHTSA · メーカー通報10245786モデルイヤー 2013原文(英語)で表示中 · 翻訳待ち詳細を見る →
技術通報中程度サスペンションNA

技術通報

Buick/chevrolet/gmc/opel: Power steering assistance malfunctions while either turning left or right. Models 2012 opel ampera, volt, 2013 lacrosse, regal, equinox, malibu, terrain, opel insignia. *pe updated 08/1/2013 *js updated 11/25/2013 *js updated 1/13/15. *pe

NHTSA · メーカー通報10050239モデルイヤー 2012原文(英語)で表示中 · 翻訳待ち詳細を見る →
技術通報中程度内装NA

技術通報

Gm: See document search button for owner letter. Driver airbag inspection. *kb updated 5/23/12. *pe

NHTSA · メーカー通報10043905モデルイヤー 2012原文(英語)で表示中 · 翻訳待ち詳細を見る →
技術通報中程度その他NA

技術通報

Gm: See document search button for owner letter. Carpeted floor mats missing. Dealers are to install carpeted floor mats when mats become available. *js

NHTSA · メーカー通報10043856モデルイヤー 2012原文(英語)で表示中 · 翻訳待ち詳細を見る →
技術通報中程度サスペンションNA

技術通報

General motors: Reservoir for power steering fluid is heat damaged and leaking. May caused problems with power steering pump. *pe

NHTSA · メーカー通報10043629モデルイヤー 2012原文(英語)で表示中 · 翻訳待ち詳細を見る →
技術通報中程度サスペンションNA

技術通報

Buick/chevrolet: It is hard to remove driver's side air bag due to revised spring design, which causes higher retaining force between driver's side air bag and steering wheel. *pe

NHTSA · メーカー通報10043315モデルイヤー 2012原文(英語)で表示中 · 翻訳待ち詳細を見る →
技術通報中程度電装NA

技術通報

Chevrolet: On certain vehicles, after updated calibrations were installed, may exhibit a possible and an estimated electric range drop. *pe updated 12/7/11. *pe

NHTSA · メーカー通報10042364モデルイヤー 2011原文(英語)で表示中 · 翻訳待ち詳細を見る →
技術通報中程度サスペンションNA

技術通報

Gm: The steering wheel adjustment is binding or sticking. This is caused by the steering wheel lever adjustment nut tightening. *rm

NHTSA · メーカー通報10038705モデルイヤー 2011原文(英語)で表示中 · 翻訳待ち詳細を見る →
技術通報中程度エンジンNA

技術通報

Gm: There is an engine oil leak at the front engine cover. 2011 volt. *rm updated 6/27/11. *pe

NHTSA · メーカー通報10038466モデルイヤー 2011原文(英語)で表示中 · 翻訳待ち詳細を見る →
技術通報中程度内装NA

技術通報

Gm: There are seat belt problems: Difficulty latching and unlatching buckle. Buckle release button is sticking. Seat belt warning light illuminated. Likely caused by sticky beverages that are spilled into the buckle assembly. *rm updated 4/3/12. *pe

NHTSA · メーカー通報10038294モデルイヤー 2011原文(英語)で表示中 · 翻訳待ち詳細を見る →
古いもの →

出典:NHTSA(米国、パブリックドメイン)、カナダ運輸省(Open Government Licence – Canada)、DVSA(英国、Open Government Licence v3.0)、RappelConso および EU Safety Gate(フランス、Licence Ouverte 2.0)、国土交通省(日本、公共データ利用規約1.0)、韓国国土交通部(car.go.kr)。