閲覧無料 · 投稿は無料アカウントでAnticars(2000年)の後継

DodgeDodge ナイトロ

2006–2011 · 1 世代 · 不具合14件 · 3市場
世代

技術サービス通報(TSB)は、既知の不具合についてメーカーが販売店に送る修理指示です。安全リコールではありませんが、不具合の裏付けになることがよくあります。

技術通報中程度その他NA

技術通報

wiTECH 小規模漏れ検証テスト(SLVT)- P0456 蒸発ガス(EVAP)システム 小規模漏れ

NHTSA · メーカー通報10236933モデルイヤー 2012自動翻訳 · 原文:英語詳細を見る →
技術通報中程度エンジンNA

技術通報

Issue involves overheating, running hot, coolant leaks and related symptoms after a Mopar replacement engine has been installed in the vehicle.

NHTSA · メーカー通報10230180モデルイヤー 2012原文(英語)で表示中 · 翻訳待ち詳細を見る →
技術通報中程度エンジンNA

技術通報

Issue involves overheating, running hot, coolant leaks and related symptoms after a Mopar replacement engine has been installed in the vehicle.

NHTSA · メーカー通報10221594モデルイヤー 2012原文(英語)で表示中 · 翻訳待ち詳細を見る →
技術通報中程度エンジンNA

技術通報

Part Description: 5.7L ロングブロック Issue Description: この5.7Lロングブロックアセンブリは、EGRおよび非EGR仕様の両方に対応しています。非EGR仕様に本ロングブロックアセンブリを取り付ける場合は、EGRブロックオフプレート(53032739AA)を注文する必要があります。ただし、古いエンジンからEGRブロックオフプレートを移設する場合はこの限りではありません。

NHTSA · メーカー通報10229181モデルイヤー 2007自動翻訳 · 原文:英語詳細を見る →
技術通報中程度エンジンNA

技術通報

Service - Four Piece Oil Pan Gasket All Cummins Equipped Vehicles ONLY - The replacement oil pan gasket can be a four piece gasket rather than a single piece gasket. This applies to Cummins 5.9L and 6.7L engines only. Installation: 1. Clean the oil pan T-joints.~ 2. Fill the T-joint between the pan rail/gear housing and pan rail/rear seal retainer with sealant. Use Mopar Silicone Rubber Adhesive Sealant or equivalent. 3. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the oil pan flange.~ 4. The four piece gasket will need to be assembled to make a complete oil pan gasket. 5. Lay the oil pan gasket(s) onto the oil pan flange.~ 6. Ensure the oil pan gasket segment joints are properly aligned. 7. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the top of the oil pan gasket.~ 8. Install the oil pan. Starting from the center and working outward, tighten the oil pan bolts to 28 Nm [21 ft. lbs.].

NHTSA · メーカー通報10223854モデルイヤー 2007原文(英語)で表示中 · 翻訳待ち詳細を見る →
技術通報中程度ブレーキNA

技術通報

Adaptive Cruise Control Sensor 1) If you are replacing this part due to the cluster displaying Clean Radar Sensor in Front of Vehicle or DTC C1266 ACC Sensor Blinded, please verify that there is no blockage in front of the sensor. Blockage can occur from mud, ice, snow, front end damage, bracket damage, the sensor not attached to the bracket properly or an aftermarket fascia installed. This fault can occur intermittently in muddy or icy/snowy conditions and is considered normal operation. Under some circumstances, a misaligned sensor can also cause the C1266 DTC, please complete an alignment procedure. No replacement is required.~ 2) If you are replacing this part due to the cluster displaying ?ACC/FCW Unavailable Service Required?, please check the DTC fault codes. This will indicate which module needs to be serviced (TCM, PCM, ESP/ABS, etc). This fault is not due to the ACC Sensor. No sensor replacement is required.~ 3) If you have fault code DTC C125E ACC Sensor Adjustment Required, please verify that the radar sensor is fully seated in the clips and there is no damage (if clips are damaged on a 2013 or earlier vehicle, order P/N 68085813A$, otherwise please replace the module), please verify there is no blockage to the sensor due to mud, ice, snow, front end damage, bracket damage or the sensor not attached to the bracket properly. Perform the Vertical Alignment and the Electronic Horizontal Alignments procedure as stated in the service manual. Please note, if the horizontal alignment procedure will not complete, check the vertical alignment and confirm that the sensor is seated properly. Rerun the horizontal alignment procedure. No sensor replacement is required. **Hints for running Horizontal Alignment procedure: A) Verify speed is between 45 and 75 mph, B) verify the road is relatively straight with signs, poles, guard rails, etc C) Do not tail a vehicle too closely this inhibits the learning procedure

NHTSA · メーカー通報10139956モデルイヤー 2012原文(英語)で表示中 · 翻訳待ち詳細を見る →
技術通報中程度エンジンNA

技術通報

Ram/dodge\jeep service campaign: See document search button for owner letter. The engine water pump on certain vehicles may leak coolant. Engine operation with a low coolant level could cause engine damage or low cabin heater output. Csc letter was rec'd. *pe

NHTSA · メーカー通報10034071モデルイヤー 2010原文(英語)で表示中 · 翻訳待ち詳細を見る →
技術通報中程度エンジンNA

技術通報

Chrysler\dodge service campaign: See document search button for owner letter. An incorrect positive crankcase ventilation (pcv) valve may have been installed. An incorrect pcv valve can cause excessive exhaust emissions. Csc letter was received. *pe

NHTSA · メーカー通報10028832モデルイヤー 2009原文(英語)で表示中 · 翻訳待ち詳細を見る →
技術通報中程度電装NA

技術通報

Emissions recall g45--veci label - an incorrect vehicle emission control information (veci) label was installed on about ten thousand vehicles. The originally installed veci label does not display the correct spark plug information. *nj

NHTSA · メーカー通報10023661モデルイヤー 2007原文(英語)で表示中 · 翻訳待ち詳細を見る →
技術通報中程度サスペンションNA

技術通報

Slight play in steering/stiff/choppy/bumpy ride. *nj

NHTSA · メーカー通報10023393モデルイヤー 2007原文(英語)で表示中 · 翻訳待ち詳細を見る →
技術通報中程度サスペンションNA

技術通報

Steering angle sensor - not initialized/internal. *kb

NHTSA · メーカー通報10021984モデルイヤー 2007原文(英語)で表示中 · 翻訳待ち詳細を見る →
技術通報軽微その他NA

技術通報

ロッカー/リフター、油圧ローラー式非作動機構 MDSリフターは、非作動ピンの位置が合っていないという理由で交換しないでください。これは正常な状態であり、不具合ではありません。

NHTSA · メーカー通報10248517モデルイヤー 2012自動翻訳 · 原文:英語詳細を見る →
技術通報軽微その他NA

技術通報

ロッカーアーム、油圧ローラー式非作動機構 MDSリフターは、切り離しピンが揃っていなくても交換しないでください。これは正常な状態であり、不具合ではありません。

NHTSA · メーカー通報10244356モデルイヤー 2012自動翻訳 · 原文:英語詳細を見る →
技術通報軽微その他NA

技術通報

キー/マスター WJ、KJ、TJ、PT Cruiser のキー/FOBIK を交換する場合は、「AC」NIC レベルの部品番号を使用してください。「AB」NIC レベルはこれらのプラットフォームにはプログラムできません。その他のすべてのプラットフォームで、「AB」NIC レベルが車両にプログラムできない場合は、「AC」NIC レベルの部品を使用し、部品保証を申請してください。

NHTSA · メーカー通報10229256モデルイヤー 2005自動翻訳 · 原文:英語詳細を見る →
技術通報軽微トランスミッションNA

技術通報

Customer Satisfaction Notification V51 Reprogram Powertrain Control Module

NHTSA · メーカー通報10228020モデルイヤー 2010原文(英語)で表示中 · 翻訳待ち詳細を見る →
技術通報軽微内装NA

技術通報

Warranty Bulletin D-20-17 (X85) Active Head Restraint - Select 2012-2013 Jeep Liberty (KK) and 2012 Dodge Nitro (KA) (Rev. A)

NHTSA · メーカー通報10224064モデルイヤー 2012原文(英語)で表示中 · 翻訳待ち詳細を見る →
技術通報軽微その他NA

技術通報

KEY, Master If replacing the key/FOBIK on a WJ, KJ, TJ, or PT Cruiser, use the "AC" NIC level part number. The "AB" NIC level will not program to these platforms. For all other platforms, if the "AB" NIC level will not program to the vehicle, use the "AC" NIC level part and submit a part warranty.

NHTSA · メーカー通報10221686モデルイヤー 2005原文(英語)で表示中 · 翻訳待ち詳細を見る →
技術通報軽微トランスミッションNA

技術通報

Gear Ratio DTC?s, Transmission Shift Concerns, Does Not Shift At Times, Shudders

NHTSA · メーカー通報10221150モデルイヤー 2012原文(英語)で表示中 · 翻訳待ち詳細を見る →
技術通報軽微トランスミッションNA

技術通報

トルクコンバーター付きトランスミッションキット 1. 全 Promaster (VF) 3.6L/62TE 搭載車。整備中にトランスミッションブラケットとトランスミッションケース間の締結ボルトを取り外した場合、そのボルト(部品番号 06511385A$)は使い捨てです。2015年10月23日以前に製造された車両には、サービスキット PN 68461214AA が必要です。このキットには、トランスミッションアイソレーター PN 68264483AA、アダプテーションブラケット 68264479AA、締結ボルトサービスキット PN 68329056AA が含まれます。2015年10月23日以降に製造された車両では、締結ボルトサービスキット PN 68329056AA のみが必要です。 2. 全 3.6L/62TE 搭載車。修理対象車両のフレックスプレートにひび割れがある場合、またはポンプブッシュの故障がある場合は、エンジンブロックに2本(2個)のダウエルピンがあることを確認してください。これらのピンは、トランスミッションの中心線とクランクシャフトの中心線を合わせる役割を担います。また、トランスミッションケースのダウエル位置合わせ穴を目視で点検してください。穴が損傷していたり伸びていたりする場合は、修理中にエンジンとトランスミッションを正しく位置合わせできないため、トランスミッション/フレックスプレートまたはポンプブッシュのさらなる損傷を防ぐために、トランスミッションを交換してください。 3. 全 62TE 搭載車。ポンプブッシュに傷や損傷があり、ダウエルピンの位置合わせ穴に問題がない場合は、トランスミッション全体ではなく、ポンプアッセンブリを交換してください。 4. 全 62TE 搭載車。車両にジャーキング/スリップが発生し、MIL コード P0740 または P2764 が出力されている場合は、TCC ソレノイドの動作を確認してください。TCC ソレノイドが正常であれば、これらのコードはトルクコンバーターの故障を示しています。トルクコンバーターを交換してください。

NHTSA · メーカー通報10220840モデルイヤー 2005自動翻訳 · 原文:英語詳細を見る →
技術通報軽微内装NA

技術通報

Warranty Bulletin D-20-21 (X91) Active Head Restraint - Select 2010 Dodge Journey (JC), Dodge Avenger/Chrysler Sebring (JS), Dodge Nitro (KA), Jeep Liberty (KK), Jeep Compass/Jeep Patriot (MK), Dodge Caliber (PM), Dodge Caravan (RT)

NHTSA · メーカー通報10187658モデルイヤー 2010原文(英語)で表示中 · 翻訳待ち詳細を見る →
技術通報軽微内装NA

技術通報

Warranty Bulletin D-20-22 (X92) Active Head Restraint - Select 2011 Dodge Journey (JC), Dodge Avenger/Chrysler 200 (JS), Dodge Nitro (KA), Jeep Liberty (KK), Jeep Compass/Jeep Patriot (MK), Dodge Caliber (PM), Dodge Caravan (RT), Dodge Durango (WD), Jeep Grand Cherokee (WK)

NHTSA · メーカー通報10187659モデルイヤー 2011原文(英語)で表示中 · 翻訳待ち詳細を見る →
技術通報軽微内装NA

技術通報

Warranty Bulletin D-20-17 (X85) Active Head Restraint - Select 2012-2013 Jeep Liberty (KK) and 2012 Dodge Nitro (KA) (Rev. B)

NHTSA · メーカー通報10187663モデルイヤー 2012原文(英語)で表示中 · 翻訳待ち詳細を見る →
技術通報軽微内装NA

技術通報

Warranty Bulletin D-20-21 (X91) Active Head Restraint - Select 2010 Dodge Journey (JC), Dodge Avenger/Chrysler Sebring (JS), Dodge Nitro (KA), Jeep Liberty (KK), Jeep Compass/Jeep Patriot (MK), Dodge Caliber (PM), Dodge Caravan/Chrysler Town & Country (RT) (Rev. A)

NHTSA · メーカー通報10187667モデルイヤー 2010原文(英語)で表示中 · 翻訳待ち詳細を見る →
技術通報軽微内装NA

技術通報

Active Head Restraint (AHR) Inadvertent Deployment - X92 Warranty Extension This bulletin involves inspecting the sled bracket striker pin and possibly replacing a front seat AHR that has inadvertently deployed. Customers may comment on the following:The AHR is deployed on one or both front seats and will not reset.

NHTSA · メーカー通報10187680モデルイヤー 2011原文(英語)で表示中 · 翻訳待ち詳細を見る →
技術通報軽微内装NA

技術通報

Active Head Restraint (AHR) Inadvertent Deployment - X91 Warranty Extension This bulletin involves inspecting the sled bracket striker pin and possibly replacinga front seat AHR that has inadvertently deployed. Customers may comment on the following: The AHR is deployed on one or both front seats and will not reset.

NHTSA · メーカー通報10187684モデルイヤー 2010原文(英語)で表示中 · 翻訳待ち詳細を見る →
古いもの →

出典:NHTSA(米国、パブリックドメイン)、カナダ運輸省(Open Government Licence – Canada)、DVSA(英国、Open Government Licence v3.0)、RappelConso および EU Safety Gate(フランス、Licence Ouverte 2.0)、国土交通省(日本、公共データ利用規約1.0)、韓国国土交通部(car.go.kr)。