閲覧無料 · 投稿は無料アカウントでAnticars(2000年)の後継

Mazda Mazda2

2002– · 3 世代 · 不具合13件 · 7市場
世代

技術サービス通報(TSB)は、既知の不具合についてメーカーが販売店に送る修理指示です。安全リコールではありませんが、不具合の裏付けになることがよくあります。

年式
Mazda2 III · 2014–
技術通報中程度電装NA

技術通報

Some customers may experience a SBS/SCBS, LAS/LDWS and/or HBC warning light on. A system error message may also be found in the center display. DTC U3000:04-0A (Forward sensing camera (FSC) internal malfunction). DTC U3000:04-0A (Forward sensing camera (FSC) internal malfunction) is stored in the FSC module and cannot be erased. This concern may be caused by a hardware failure of an internal device of the FSC, which results in a malfunction detection. To eliminate this concern, the production process of the FSC has been modified.

NHTSA · メーカー通報10199641モデルイヤー 2021原文(英語)で表示中 · 翻訳待ち詳細を見る →
Mazda2 III · 2014–
技術通報中程度電装NA

技術通報

If you experience issues with the current version of ID's such as missing tools or modules not showing after completing a network test, be advised that we are aware of these issues and are working to resolve them. As a counter measure, it is advised that you un-install ids and re-install version 103.00 and "do not update" until further notice.

NHTSA · メーカー通報10185813モデルイヤー 2017原文(英語)で表示中 · 翻訳待ち詳細を見る →
Mazda2 III · 2014–
技術通報軽微電装NA

技術通報

Some customers may complain about any of the following: 1. インフォテインメントセンターのディスプレイに、MyMazdaアプリのコネクテッドビークル登録時の認証コード(OTP)が表示されない。 2. リモート機能が使用できない。

NHTSA · メーカー通報11039110モデルイヤー 2021自動翻訳 · 原文:英語詳細を見る →
Mazda2 III · 2014–
技術通報軽微電装NA

技術通報

一部の車両では、チェックエンジンランプが点灯し、DTC P0300:00(ランダム失火検出)が記録されることがあります。これは、PCMの制御ロジックが不適切なため、失火を誤検知することが原因と考えられます。この問題を解消するため、PCMの制御ロジックを変更しました。

NHTSA · メーカー通報11012337モデルイヤー 2021自動翻訳 · 原文:英語詳細を見る →
Mazda2 III · 2014–
技術通報軽微電装NA

技術通報

顧客によっては、走行中にチャージランプ(充電警告灯)が点灯することに気付く場合があります。点検の結果、DTC P2502:00 PCM(発電機が発生する電圧の異常)がメモリーに記録されていることが確認されています。これは、回路基板とアース間の抵抗が原因となっている可能性があります。大電流が流れた際に、アース端子の取り付け位置の接触が十分でない場合があります。この問題を解消するため、DC-DCコンバーターの制御ソフトウェアを変更しました。さらに、製造工程も見直しています。アース端子と回路基板の締め付けトルクを増加させました。

NHTSA · メーカー通報11008418モデルイヤー 2021自動翻訳 · 原文:英語詳細を見る →
Mazda2 III · 2014–
技術通報軽微電装NA

技術通報

Some customers may experience a check engine light illumination at idle while stopped with DTC P0300:00 stored, resulting in rough idle conditions. P0300:00: Random misfire detected This concern is caused by improper engine control in the idle range. To eliminate the concern, the PCM control software has been modified.

NHTSA · メーカー通報11008417モデルイヤー 2021原文(英語)で表示中 · 翻訳待ち詳細を見る →
Mazda2 III · 2014–
技術通報軽微電装NA

技術通報

BSM Radar aiming cannot be performed after rightside BSM control module rekkplacement

NHTSA · メーカー通報10213434モデルイヤー 2016原文(英語)で表示中 · 翻訳待ち詳細を見る →
Mazda2 III · 2014–
技術通報軽微電装NA

技術通報

Some customers may experience the CHECK ENGINE light ON with DTC P0089:00 (Spill valve control solenoid valve control circuit range/performance problem) stored. This is caused by improper control software of the PCM detecting a false error, even with normal fuel pressure operation. To correct this issue, the control software of the PCM has been modified.

NHTSA · メーカー通報10190951モデルイヤー 2021原文(英語)で表示中 · 翻訳待ち詳細を見る →
Mazda2 III · 2014–
技術通報軽微電装NA

技術通報

Some vehicles may experience a fuzzy appearance (tiny cracks) around the edge of the Active Driving Display. Replace the Active Driving Display.

NHTSA · メーカー通報10185954モデルイヤー 2016原文(英語)で表示中 · 翻訳待ち詳細を見る →
Mazda2 III · 2014–
技術通報軽微電装NA

技術通報

Some vehicles may experience the check engine light on with DTCs P2096:00, P2097:00 and/or P0524:00 that cannot be cleared by itself, and the check engine light stays on even if the detection condition has gone. P2096:00 - Air fuel too lean P2097:00 - Air fuel too rich P0524:00 - Engine oil pressure too low. This concern may be caused by improper PCM control logic. The PCM software has been modified to eliminate this concern.

NHTSA · メーカー通報10180595モデルイヤー 2019原文(英語)で表示中 · 翻訳待ち詳細を見る →
Mazda2 III · 2014–
技術通報軽微電装NA

技術通報

Some vehicles may experience a fuzzy appearance (tiny cracks) around the edge of the Active Driving Display.

NHTSA · メーカー通報10188483モデルイヤー 2016原文(英語)で表示中 · 翻訳待ち詳細を見る →
Mazda2 III · 2014–
技術通報軽微電装NA

技術通報

New IDs software version 102.00 and Update 102.01 is now available on MS3 IDs update 102.00 and 102.01 is now available on MS3 under the "IDs/Infotainment" tab.

NHTSA · メーカー通報10186918モデルイヤー 2017原文(英語)で表示中 · 翻訳待ち詳細を見る →
Mazda2 III · 2014–
技術通報軽微電装NA

技術通報

Active driving display opens/closes improperly. Some vehicles may exhibit the active driving display opening/closing improperly as described below: * It does not open or close when the ignition is turned ON or OFF . * The display operation does not fully open/close. * It closes and then opens by itself while the vehicle is moving. This concern may be caused by voltage fluctuation to the act ive driving display which activates pinching detection. Customer having this concern should have their vehicle repaired using the following repair procedure.

NHTSA · メーカー通報10186257モデルイヤー 2016原文(英語)で表示中 · 翻訳待ち詳細を見る →
Mazda2 III · 2014–
技術通報軽微電装NA

技術通報

Some customers may experience the active driving display (auto flip-up type) does not flip up and no DTC is stored. Due to improper assembly, a deformed bracket may cause a loose mesh between internal gears. To correct this issue, the active driving display has been changed.

NHTSA · メーカー通報10144332モデルイヤー 2018原文(英語)で表示中 · 翻訳待ち詳細を見る →
Mazda2 III · 2014–
技術通報軽微電装NA

技術通報

Some vehicles may experience a fuzzy appearance (tiny cracks) around the edge of the Active Driving Display. Replace the Active Driving Display.

NHTSA · メーカー通報10125470モデルイヤー 2016原文(英語)で表示中 · 翻訳待ち詳細を見る →
Mazda2 III · 2014–
技術通報軽微電装NA

技術通報

If the right-side bsm control module requires replacement for any repair, also replace the left side bsm control module to complete the radar aiming procedure (it is ok to replace the left bsm alone). Reason if the right-side bsm control module is replaced alone, automatic configuration is not performed due to a program error in the module. Because of this, the required bsm radar aiming cannot be performed. Automatic configuration as well as bsm radar aiming can be performed, if the left-side bsm control module is replaced alone or together with the right-side bsm control module.

NHTSA · メーカー通報10105642モデルイヤー 2016原文(英語)で表示中 · 翻訳待ち詳細を見る →
Mazda2 III · 2014–
技術通報軽微電装NA

技術通報

If the right-side bsm control module requires replacement for any repair, also replace the left side bsm control module to complete the radar aiming procedure (it is ok to replace the left bsm alone). Reason if the right-side bsm control module is replaced alone, automatic configuration is not performed due to a program error in the module. Because of this, the required bsm radar aiming cannot be performed. Automatic configuration as well as bsm radar aiming can be performed, if the left-side bsm control module is replaced alone or together with the right-side bsm control module.

NHTSA · メーカー通報10101468モデルイヤー 2016原文(英語)で表示中 · 翻訳待ち詳細を見る →
Mazda2 III · 2014–
技術通報軽微電装NA

技術通報

Some vehicles may experience a fuzzy appearance (tiny cracks) around the edge of the active driving display. Replace the active driving display.

NHTSA · メーカー通報10101464モデルイヤー 2016原文(英語)で表示中 · 翻訳待ち詳細を見る →
Mazda2 III · 2014–
技術通報軽微電装NA

技術通報

If the active driving display (ad-disp) unit requires removal, use caution when disconnecting/connecting the wiring harness. If the harness is not connected properly, the ad-disp may not operate.

NHTSA · メーカー通報10091601モデルイヤー 2016原文(英語)で表示中 · 翻訳待ち詳細を見る →
Mazda2 III · 2014–
技術通報軽微電装NA

技術通報

Some vehicles may experience a fuzzy appearance (tiny cracks) around the edge of the active driving display. Replace the active driving display.

NHTSA · メーカー通報10090902モデルイヤー 2016原文(英語)で表示中 · 翻訳待ち詳細を見る →
Mazda2 III · 2014–
技術通報軽微電装NA

技術通報

If the active driving display (ad-disp) unit requires removal, use caution when disconnecting/connecting the wiring harness. If the harness is not connected properly, the ad-disp may not operate.

NHTSA · メーカー通報10090667モデルイヤー 2016原文(英語)で表示中 · 翻訳待ち詳細を見る →
Mazda2 III · 2014–
技術通報軽微電装NA

技術通報

Bsm radar aiming cannot be performed after right-side bsm control module replacement. If right-dide bsm control module requres replacement for any repair, also replace left side bsm control module to compelte the radar aiming procedure (it's ok to replace the left bsm alone). If the right-side bsm control module is replaced alone, "automatic configuration" is not performed due to program error in module. Because of this, the required "bsm radar aiming" cannot be performed. "automatic configuration" as well as "bsm radar aiming" can be performed if left-side bsm control module is replaced alone or together with right-side bsm control module.

NHTSA · メーカー通報10076685モデルイヤー 2016原文(英語)で表示中 · 翻訳待ち詳細を見る →
Mazda2 II · 2007–2014
技術通報軽微電装NA

技術通報

Mazda: There is possible excessive condensation or water inside the headlamp unit on many mazda models. *rm

NHTSA · メーカー通報10037949モデルイヤー 2011原文(英語)で表示中 · 翻訳待ち詳細を見る →
Mazda2 II · 2007–2014
技術通報軽微電装NA

技術通報

Mazda: There is condensation and fog in the front and rear combination lights. *rm

NHTSA · メーカー通報10037655モデルイヤー 2011原文(英語)で表示中 · 翻訳待ち詳細を見る →

出典:NHTSA(米国、パブリックドメイン)、カナダ運輸省(Open Government Licence – Canada)、DVSA(英国、Open Government Licence v3.0)、RappelConso および EU Safety Gate(フランス、Licence Ouverte 2.0)、国土交通省(日本、公共データ利用規約1.0)、韓国国土交通部(car.go.kr)。