技術通報
Tire pressure monitoring system (TPMS) warning Light IlluminationMisure prevention logic
🔔 無料アカウントを作成して Mazda Mazda2 (すべての世代) のメール通知を受け取る
技術サービス通報(TSB)は、既知の不具合についてメーカーが販売店に送る修理指示です。安全リコールではありませんが、不具合の裏付けになることがよくあります。
Tire pressure monitoring system (TPMS) warning Light IlluminationMisure prevention logic
Some customers may experience a SBS/SCBS, LAS/LDWS and/or HBC warning light on. A system error message may also be found in the center display. DTC U3000:04-0A (Forward sensing camera (FSC) internal malfunction). DTC U3000:04-0A (Forward sensing camera (FSC) internal malfunction) is stored in the FSC module and cannot be erased. This concern may be caused by a hardware failure of an internal device of the FSC, which results in a malfunction detection. To eliminate this concern, the production process of the FSC has been modified.
いくつかの車両では、寒く湿度の高い天候に駐車した後、ブレーキをかけた際にフロントブレーキから キーキー という異音が発生することがあります。低温下ではパッドの摩擦抵抗が増加するため、パッドが振動しやすくなり、この鳴き音が生じます。
A/C blows warm air. Some customers may complain about warm air from the climate cointrol vents. This may be caused by improper brazing (A) of the evaporator (B) causing a refrigerant leak fr om the joint between the tubes and the header (D)
If you experience issues with the current version of ID's such as missing tools or modules not showing after completing a network test, be advised that we are aware of these issues and are working to resolve them. As a counter measure, it is advised that you un-install ids and re-install version 103.00 and "do not update" until further notice.
Some vehicles may exhibit an unusual noise from around the drivers foot area when repeatedly turning the steering wheel to the left or right. A vibration is felt at the steering wheel when the noise occurs. This concern may be caused by a lack of grease application to the splines of the intermediate shaft at the production line. The grease application process has been improved.
Some customers may complain about any of the following: 1. インフォテインメントセンターのディスプレイに、MyMazdaアプリのコネクテッドビークル登録時の認証コード(OTP)が表示されない。 2. リモート機能が使用できない。
一部の車両では、チェックエンジンランプが点灯し、DTC P0300:00(ランダム失火検出)が記録されることがあります。これは、PCMの制御ロジックが不適切なため、失火を誤検知することが原因と考えられます。この問題を解消するため、PCMの制御ロジックを変更しました。
顧客によっては、走行中にチャージランプ(充電警告灯)が点灯することに気付く場合があります。点検の結果、DTC P2502:00 PCM(発電機が発生する電圧の異常)がメモリーに記録されていることが確認されています。これは、回路基板とアース間の抵抗が原因となっている可能性があります。大電流が流れた際に、アース端子の取り付け位置の接触が十分でない場合があります。この問題を解消するため、DC-DCコンバーターの制御ソフトウェアを変更しました。さらに、製造工程も見直しています。アース端子と回路基板の締め付けトルクを増加させました。
Some customers may experience a check engine light illumination at idle while stopped with DTC P0300:00 stored, resulting in rough idle conditions. P0300:00: Random misfire detected This concern is caused by improper engine control in the idle range. To eliminate the concern, the PCM control software has been modified.
Front/Rear stabilizer noise prevention
MultiModel(skyactivdrive搭載)ATF色の劣化 新車時のオートマチックトランスミッションフルード(ATF)の色は青色です。走行距離が増えるとATFの色は変化します。この色の変化が車両の性能に影響することはありません。
BSM Radar aiming cannot be performed after rightside BSM control module rekkplacement
Mazda Technical Service Bulletins March 2016 Some vehicles may exhibit the inner cloth (A) falling down at the rear end causing a poor appearance and obstructing the view of the back window.
Maintenance.
マツダ・コネクテッドサービス - よくある質問(FAQ): 目次:一般的な質問、設定と使い始め、登録/加入、Wi-Fi一般情報、Wi-Fi操作方法、Wi-Fiトライアル期間、アプリとのやり取り、サービスに関する問題、トラブルシューティング、受信レベルの点検、販売店での手続き、リモートエンジン始動が機能しない条件、リモートエンジン始動機能でエンジンが停止する条件、教育用ビデオ、リソース
## マツダ・コネクテッドサービス - よくある質問(FAQ) 目次:一般的な質問、セットアップと利用開始、登録/加入、Wi-Fi 一般情報、Wi-Fi 操作方法、Wi-Fi トライアル期間、アプリの操作、サービスに関する問題、トラブルシューティング、受信レベルの確認、販売店での手続き、リモートエンジン始動が機能しない条件、リモートエンジン始動機能によりエンジンが停止する条件、教育用動画、リソース
Some customers may experience the CHECK ENGINE light ON with DTC P0089:00 (Spill valve control solenoid valve control circuit range/performance problem) stored. This is caused by improper control software of the PCM detecting a false error, even with normal fuel pressure operation. To correct this issue, the control software of the PCM has been modified.
Some vehicles may experience a fuzzy appearance (tiny cracks) around the edge of the Active Driving Display. Replace the Active Driving Display.
Beginning with the CX-5 and Mazda6 models, grip type front and rear stabilizer bushings have been incorpo-rated for noise prevention purposes. If any type of grease or lubrication is applied to the bushings, it may create noise due to bushing slippage.
Some vehicles may experience the check engine light on with DTCs P2096:00, P2097:00 and/or P0524:00 that cannot be cleared by itself, and the check engine light stays on even if the detection condition has gone. P2096:00 - Air fuel too lean P2097:00 - Air fuel too rich P0524:00 - Engine oil pressure too low. This concern may be caused by improper PCM control logic. The PCM software has been modified to eliminate this concern.
Some vehicles may experience a fuzzy appearance (tiny cracks) around the edge of the Active Driving Display.
New IDs software version 102.00 and Update 102.01 is now available on MS3 IDs update 102.00 and 102.01 is now available on MS3 under the "IDs/Infotainment" tab.
Recall 0516j updated repair procedure
Windshield washer fluid change - Factory filled windshield washer fluid has been changed to an ethanol type (yellow color) instead of athe conventional methanol type (blue color). This change is for European compliance Mazda has decided to make the change for all markets.
出典:NHTSA(米国、パブリックドメイン)、カナダ運輸省(Open Government Licence – Canada)、DVSA(英国、Open Government Licence v3.0)、RappelConso および EU Safety Gate(フランス、Licence Ouverte 2.0)、国土交通省(日本、公共データ利用規約1.0)、韓国国土交通部(car.go.kr)。