Mitsubishi Motors North America, Inc. (MMNA)は、1999年4月5日から2004年12月17日に製造された2000~2005年式Eclipse車両、2000年1月19日から2005年3月18日に製造された2001~2005年式Eclipse Spyder車両、2000年4月17日から2005年2月21日に製造された2001~2005年式Chrysler Sebring車両、および2000年4月17日から2005年2月22日に製造された2001~2005年式Dodge Stratus車両の一部をリコールしています。対象車両では、助手席側のサンバイザーが、助手席側フロンタルエアバッグが展開した際にサンバイザーが外れる可能性がある位置まで折りたたまれている場合があります。
On certain passenger vehicles, the metal forming part of the front crossmember may have been improperly stamped resulting in the metal becoming thinner in the cross-section than specified. This could, over time, result in breakage of the crossmember.
On certain vehicles, the fuel return line hose fitting on the electric fuel pump may be restricted, causing excessive fuel pressure to build up in the fuel injection system. Excessive fuel pressure may result in the fuel return hose becoming dislodged, resulting in fuel leakage. Fuel leakage in the presence of an ignition source could result in a fire. Correction: Dealer will inspect the fuel pump pressure. Those vehicles exhibiting higher than normal fuel pump pressure will receive fuel pump modifications.
On certain passenger vehicles, the fuel return line hose fitting on the electric fuel pump may be restricted, causing excessive fuel pressure to build up in the fuel injection system. Excessive fuel pressure may result in a leak in the fuel return hose.
Vehicle description: Passenger vehicles built with v6 engines to federal emission standards. The power steering fluid feed tube can come in contact with an exhaust manifold mounted heat shield causing a hole to be worn through the power steering pipe allowing fluid leakage.
Vehicle description: Passenger vehicles built with v6 engines to federal emission standards. The power steering fluid feed tube can come in contact with an exhaust manifold mounted heat shield causing a hole to be worn through the power steering pipe allowing fluid leakage.
Vehicle description: Passenger vehicles. A bulge in the fuel tank caused by the manufacturing process resulted in thinning of the material during a welding operation, increasing the risk of fuel leakage.
Vehicle description: Passenger vehicles. A nut in the steering gear assembly was not properly tightened, resulting in symptoms ranging from steering wheel vibration to stiff steering, and in the worst case, no ability to turn left.
Vehicle description: Passenger vehicles. A nut in the steering gear assembly was not properly tightened, resulting in symptoms ranging from steering wheel vibration to stiff steering, and in the worst case, no ability to turn left.
The headlamp support panel can develop a fatigue crack where the anti-lock brake system (abs) hydraulic unit is attached, allowing the hydraulic unit to fall down.
Diluted primer may have been used on the windshield opening flanges prior to windshield glass installation which would not provide the retention required by fmvss 212.
Mitsubishi Motors North America, Inc. (MMNA) is recalling certain model year 2006-2009 Eclipse vehicles manufactured April 20, 2005, to February 13, 2009, and 2007-2009 Eclipse Spyder vehicles manufactured December 23, 2005, to February 13, 2009. Due to corrosion inside the antil-lock brake system (ABS) unit, one or more of the internal valves may seize. In a braking event that uses the ABS, a seized valve would increase brake pedal travel and reduce braking ability.
On certain vehicles, corrosion may occur in the ABS hydraulic unit due to a reaction between the brake fluid and the surface treatment of the internal valves. If this were to occur and the ABS hydraulic unit is activated, one or more of the valves could seize. This could result in longer brake pedal travel and increased stopping distances, which may increase the risk of a crash causing injury and/or damage to property. Correction: Dealers will flush and clean the hydraulic unit by replacing the brake fluid with higher grade (DOT4) fluid. If module valve movement is determined to be poor, the ABS hydraulic unit will be replaced.
On certain vehicles equipped with automatic transmissions, the key lock cable was improperly manufactured and may not allow the cable end to lock into the floor shifter mechanism. This can result in the interlock system to become inoperative and allow the ignition key to be removed without the gearshift mechanism being placed in the park position.
On certain passenger vehicles, one of four seals inside the master cylinder may have been installed improperly. As a result, the master cylinder may unexpectedly by-pass hydraulic braking force pressure and allow a longer than normal pedal stroke.
出典:NHTSA(米国、パブリックドメイン)、カナダ運輸省(Open Government Licence – Canada)、DVSA(英国、Open Government Licence v3.0)、RappelConso および EU Safety Gate(フランス、Licence Ouverte 2.0)、国土交通省(日本、公共データ利用規約1.0)、韓国国土交通部(car.go.kr)。