Bei bestimmten Fahrzeugen kann der vordere Airbag-Inflator des Fahrers beim Auslösen des Airbags einen übermäßigen internen Druck erzeugen. Erhöhter Druck kann dazu führen, dass der Inflator platzt, wodurch Fragmente auf die Fahrzeuginsassen geschleudert werden und das Verletzungsrisiko erhöht werden. Dies könnte auch das Airbag-Modul beschädigen, was eine ordnungsgemäße Auslösung verhindert. Das Nichtauslösen des Airbags während eines Unfalls (sofern ein Auslösen erforderlich ist) könnte das Risiko einer Verletzung des Sitzinsassen erhöhen. Korrektur: Händler werden den Fahrerairbag-Inflator bei Saab 9-3 und 9-5 ersetzen und das Fahrer-Airbag-Modul bei Saturn Astra ersetzen.
General Motors LLC (GM) ruft bestimmte Saab 9-3-Fahrzeuge der Modelljahre 2006-2011 zurück, die vom 31. Mai 2002 bis 15. Februar 2011 hergestellt wurden, sowie Saab 9-5 Fahrzeuge vom 7. Juni 2005 bis 28. Mai 2009 sowie Saturn Astra Fahrzeuge von 2008 bis 2009 von 2008 bis 2009 zurück. Beim Auslösen des Frontairbags des Fahrers kann ein übermäßiger Innendruck dazu führen, dass der Inflator platzt.
Es wurde festgestellt, dass im unwahrscheinlichen Fall einer Kollision, bei der das Auslösen des Fahrerairbags erforderlich ist, das Airbag-Modul des Fahrers sich von seiner Befestigung an der Hupeplatte des Lenkrads lösen könnte.
Certain passenger vehicles equipped with b308 6-cylinder gasoline engines may experience overheating and burnout of the isolated gated bipolar transistor (igbt) within the ignition discharge module (idm) due to increased susceptibility to electrical loads.
Certain 2000-2002 Saab 9-3 and 9-5 model vehicles equipped with 4-cylinder gasoline engines, and 2001-2003 9-5 models equipped with 6-cylinder gasoline engines may experience overheating and burnout of the Isolated Gated Bipolar Transistor (IGBT) within the Ignition Discharge Module (IDM) due to increased susceptibility to electrical loads. Overheating of the IGBT occurs most often at engine start-up but may also occur while the engine is running. When the IDM fails on a 4-cylinder while it is running, the engine may stall without warning, with no ability to be restarted. When the IDM fails on a 6-cylinder engine while it is running, the driver will initially experience reduced power and rough operation because the engine will only be running on three cylinders. The check engine light will flash. If the driver continues, unburnt fuel in the exhaust can cause thermal damage to the catalytic converter. The engine may stall and not restart. Correction: Dealers will inspect and, if required, replace the IDM.
Transport Canada20. Sept. 20052005271Modelljahre 2000–2003Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Certain passenger vehicles equipped with b205/b235 4-cylinder gasoline engines and b308 6-cylinder gasoline engines may experience overheating and burnout of the isolated gated bipolar transistor (igbt) within the ignition discharge module (idm) due to increased susceptibility to electrical loads.
On certain passenger vehicles, if an owner changes their wheels/tires between summer and winter using a steel wheel in the winter and an alloy wheel in the summer, it is possible for rust and contamination to build up on the wheel hub during the steel wheel usage. If this occurs and the contamination is not removed, it is possible that after the tire change service, some of this contamination could flake or grind away resulting in reduced clamping force of the wheel to the hub. Over several seasons, it is possible that this reduced force could result in fractures developing in the wheel bolts due to wheel to hub movement.
Saab is recalling 57,389 my 2002-2008 9-5 series vehicles for failing to comply with the requirements of federal motor vehicle safety standard no. 201, "occupant protection in interior impact." during compliance testing, one of the upper interior occupant protection test points exceeded the standard's requirements.
On certain vehicles, when changing back and forth between alloy and steel wheels (as for winter tires), rust and other contaminates may build up on the mating surface of the wheel hubs. If this surface is not cleaned between wheel changes, uneven torque forces may cause wheel bolts to fracture. Although this is most likely to happen during wheel change service, it is possible that the bolts may break later while the vehicle is being driven. Correction: Dealer will clean the hub and reinstall the wheel with improved bolts and attached washers that will eliminate the clamping force reduction.
Transport Canada23. Dez. 20022002247Modelljahre 1999–2003Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Eine Kombination aus inneren und äußeren Kräften führte dazu, dass sich der Kupplungskugelkopf vorzeitig vom Kupplungskugelgehäuse löste, wodurch sich der Anhänger vom Zugfahrzeug trennte.
Quellen: NHTSA (USA, gemeinfrei), Transport Canada (Open Government Licence – Canada), DVSA (Vereinigtes Königreich, Open Government Licence v3.0), RappelConso und EU-Safety-Gate (Frankreich, Licence Ouverte 2.0), MLIT (Japan, Public Data License 1.0) und MOLIT (Südkorea, car.go.kr).