Lectura libre · cuenta gratuita para colaborarSucesor de Anticars (2000)

Mazda MX-5

1989– · 4 generaciones · 35 averías documentadas · 4 mercados
Generaciones

Los boletines técnicos (TSB) son instrucciones de reparación que los fabricantes envían a sus concesionarios sobre problemas conocidos. No son llamadas a revisión de seguridad, pero a menudo confirman una avería.

Año del modelo
MX-5 (ND) · 2015–
BoletínCríticoMotorNA

Boletín

On some vehicles, a sulfur smell or 'rotten egg' odor may be noticed coming from the exhaust system. The odor is usually noticed after a cold start, fast idle, extended periods of idling and full throttle acceleration. Sulfur smell is not an indication of an engine concern and will not cause reduced driveability or durability of the engine or any of its emission components. The sulfur smell or 'rotten egg' odor is caused by high amounts of sulfur in the gasoline being used in the vehicle. Sulfur is normally eliminated during the refining process, but the EPA regulation of sulfur in gasoline differs from state to state. Vehicles using fuel containing high amounts of sulfur will most likely emit sulfur smell from the exhaust system.When high sulfur fuel is burned, there is a chemical reaction in the catalytic converter causing the sulfur tooxidize. As the vehicle is driven, the oxidizing reaction odor in the converter will decrease with mileage and age.

NHTSA · boletín del fabricante10153311Años modelo 2019Mostrado en inglés original · traducción pendienteVer detalles →
MX-5 (ND) · 2015–
BoletínModeradoCarroceríaNA

Boletín

Este boletín sustituye a los boletines publicados anteriormente que se enumeran a continuación. Los cambios aparecen marcados en rojo. 09-012/21 13/12/21, 10/06/21 y 27/04/21 DESCRIPCIÓN Es posible que algunos clientes experimenten todos los síntomas siguientes: El bloqueo y desbloqueo de las puertas no funciona al pulsar el botón del mando a distancia. 1. El bloqueo y desbloqueo de las puertas no funciona al utilizar el sensor táctil de bloqueo y desbloqueo de las puertas. 2. El motor no arranca al girar la llave de contacto. 3. El mando a distancia se activa por sí solo. 4. La pila de la llave se agota más rápido de lo habitual. 5. Síntomas 1-3: Esto puede deberse a que se aplica una carga excesiva al mando a distancia, lo que deforma los terminales eléctricos y provoca un mal contacto con la pila. Para solucionar este problema, se ha modificado la estructura del mando a distancia con el fin de reducir la deformación de los terminales eléctricos. Síntomas 4 y 5: Esto puede deberse a que se aplica una carga excesiva al mando a distancia, lo que crea un hueco alrededor de la junta por donde entra humedad y corroe la placa de circuitos, lo que a su vez agota la batería de la llave más rápido de lo habitual. Para solucionar este problema, se ha aumentado el grosor de la pared de la carcasa en la superficie de montaje de la junta y se ha mejorado la resistencia de la unión de los componentes para evitar la deformación. PROCEDIMIENTO DE REPARACIÓN Si la batería está defectuosa o mal instalada, sustitúyela y/o instálela correctamente. Si la función de ahorro de energía del mando a distancia está desactivada y la batería está en buen estado y correctamente instalada, sustituya el mando a distancia defectuoso por uno modificado siguiendo las instrucciones de MGSS (PROGRAMACIÓN DE PIEZAS RELACIONADAS CON EL SISTEMA INMOVILIZADOR). NOTA: NO sustituya otros mandos a distancia del vehículo si no presentan ningún problema.

NHTSA · boletín del fabricante11034436Años modelo 2020Traducido automáticamente · original: inglésVer detalles →
MX-5 (ND) · 2015–
BoletínModeradoMotorNA

Boletín

Some vehicles may exhibit oil leakage from the drive belt auto tensioner and rattling noises from the engine compartment. This may be caused by insufficient sealing at the drive belt auto tensioner damper when the auto tensioner fully operates under both high ambient temperature and high load conditions. To eliminate this concern, the shape of the drive belt auto tensioner damper has been changed.

NHTSA · boletín del fabricante10238663Años modelo 2019Mostrado en inglés original · traducción pendienteVer detalles →
MX-5 (ND) · 2015–
BoletínModeradoSuspensiónNA

Boletín

The Blind Spot Monitoring (BSM) system can malfunction with the following symptoms if the rear side radar sensors are installed facing the wrong direction. - BSM system indicates vehicle on the opposite side. - i-ACTIVSENSE indicator ring will not turn green - Rear Cross Traffic Alert (RCTA) does not work - Rear side radar sensor

NHTSA · boletín del fabricante10222563Años modelo 2023Mostrado en inglés original · traducción pendienteVer detalles →
MX-5 (ND) · 2015–
BoletínModeradoFrenosNA

Boletín

Some vehicles may experience a lack of power and the check engine light on with DTC P061B:00 stored in PCM memory under one of the following conditions (A or B). - DTC P061B:00 - [PCM] Internal control module torque calculation performance problem. Condition Condition Description A When cranking is interrupted (likely occurs when the brake pedal is released during cranking) B When accelerating from 1300-1600 rpm with wide open throttle Due to an improper control logic of the PCM, the engine torque calculation error detection is too sensitive. To eliminate this concern, the PCM software has been modified.

NHTSA · boletín del fabricante10218722Años modelo 2019Mostrado en inglés original · traducción pendienteVer detalles →
MX-5 (ND) · 2015–
BoletínModeradoFrenosNA

Boletín

Clunk/Rattle noise from rear brake

NHTSA · boletín del fabricante10213396Años modelo 2016Mostrado en inglés original · traducción pendienteVer detalles →
MX-5 (ND) · 2015–
BoletínModeradoCarroceríaNA

Boletín

Some vehicles may experience one of the following 2 symptoms, even though the windshield is clear. Under certain driving conditions, the Forward Sensing Camera (FSC) may detect a dirty windshield (not clear). NOTE FOR CUSTOMER: The FSC may not work properly under the conditions: The windshield is not clear. The FSC lens is not clear. Driving in heavy rain, dense fog or snow, or into the sun. Driving on a road with no or blurred road lane markings. When the windshield becomes foggy in the winter time or other cold weather conditions and LDWS/HBC warning lights turn on, drive with the defroster on for about 10 minutes. This will help clear the foggy windshield at the FSC.

NHTSA · boletín del fabricante10185957Años modelo 2016Mostrado en inglés original · traducción pendienteVer detalles →
MX-5 (ND) · 2015–
BoletínModeradoOtroNA

Boletín

Some vehicles may exhibit the inner cloth (A) falling down at the rear end causing a poor appearance and obstructing the view of the back window. This is caused by the J-hook binding holding the inner cloth coming loose during the opening/closing of the convertible top, from vibration during driving or from high ambient temperatures. To correct the problem, two top-protector clips have been additionally installed to both side edges of the J-hook to prevent the J-hook from loosening and separating.

NHTSA · boletín del fabricante10185955Años modelo 2016Mostrado en inglés original · traducción pendienteVer detalles →
MX-5 (ND) · 2015–
BoletínModeradoElectrónicaNA

Boletín

Ldws and hbc warning lights on and dtc c1001:92

NHTSA · boletín del fabricante10186337Años modelo 2016Mostrado en inglés original · traducción pendienteVer detalles →
MX-5 (ND) · 2015–
BoletínModeradoElectrónicaNA

Boletín

If you experience issues with the current version of ID's such as missing tools or modules not showing after completing a network test, be advised that we are aware of these issues and are working to resolve them. As a counter measure, it is advised that you un-install ids and re-install version 103.00 and "do not update" until further notice.

NHTSA · boletín del fabricante10185813Años modelo 2017Mostrado en inglés original · traducción pendienteVer detalles →
MX-5 (ND) · 2015–
BoletínModeradoMotorNA

Boletín

If an engine assembly is replaced after a catastrophic internal mechanical failure, clean the intake manifold internally before installing a replacement engine assembly. If the intake manifold is not cleaned properly, the replacement engine may fail prematurely. Metallic debris from the old engine (with catastrophic internal mechanical failure) may rest inside the intake manifold. When the new engine assembly is installed, debris in the intake manifold will be ingested into the new engine and cause internal damage.

NHTSA · boletín del fabricante10165676Años modelo 2019Mostrado en inglés original · traducción pendienteVer detalles →
MX-5 (ND) · 2015–
BoletínModeradoCarroceríaNA

Boletín

Some customers may complain of a lack of power under heavy load without any warning lights or DTCs. This concern may be due to a loose or detached hood weatherstrip, which can cause a blockage or restriction in the air intake system.

NHTSA · boletín del fabricante10165350Años modelo 2019Mostrado en inglés original · traducción pendienteVer detalles →
MX-5 (ND) · 2015–
BoletínModeradoOtroNA

Boletín

Due to a database error discovered with IDS 114.00-114.02 release (which affects Recall 3719F), it will be necessary to uninstall IDS 114 and install IDS 113.00 and 113.06 update. The Recall can be performed after removing IDS 114 and installing IDS 113. This SA will be updated when more information is available.

NHTSA · boletín del fabricante10163333Años modelo 2019Mostrado en inglés original · traducción pendienteVer detalles →
MX-5 (ND) · 2015–
BoletínModeradoOtroNA

Boletín

On May 1, 2018, Japan produced vehicles starting using 17 mm hex lug nuts instead of 21 mm on the same size thread. When installing the accessory locking lug nuts, make sure to use the appropriate part number for the vehicle you are working on.

NHTSA · boletín del fabricante10159199Años modelo 2018–2019Mostrado en inglés original · traducción pendienteVer detalles →
MX-5 (ND) · 2015–
BoletínModeradoSuspensiónNA

Boletín

On May 1, 2018, Japan produced vehicles starting using 17 mm hex lug nuts instead of 21 mm on the same size thread. When installing new lug nuts or the accessory Wheel Lock Set, make sure to use the appropriate part number for the vehicle you are working on.

NHTSA · boletín del fabricante10159196Años modelo 2018–2019Mostrado en inglés original · traducción pendienteVer detalles →
MX-5 (ND) · 2015–
BoletínModeradoOtroNA

Boletín

En apoyo de la nueva distribución de MRT, Mazda enviará a los concesionarios un nuevo Detector de Fugas de Diagnóstico de Doble Propósito a partir de marzo de 2019. Los videos de capacitación se publicarán en MGSS en breve, y los procedimientos del Manual de Taller se revisarán gradualmente.

NHTSA · boletín del fabricante10154879Años modelo 2019Traducido automáticamente · original: inglésVer detalles →
MX-5 (ND) · 2015–
BoletínModeradoSuspensiónNA

Boletín

Subject: Mazda Service Program (MSP) 53. 2019 CX-3 & 2018-2019 MX-5 With Direct Tire Pressure Monitoring System (TPMS) Panic Alarm System Activates While Driving. Mazda Motor Corporation has decided to conduct a Mazda Service Program (MSP) on certain 2019 CX-3 vehicles produced from February 27, 2018 through October 12, 2018 and 2018-2019 MX-5 vehicles produced from October 3, 2017 through October 15, 2018. On certain subject vehicles equipped with Direct TPMS (TPMS wheel sensor is directly mounted on each wheel), it is possible that the panic alarm system may activate while driving, and the horn may sound intermittently, and hazard warning lights may flash. The panic alarm concern will stop after cycling the ignition switch off, then on again. No DTCs are stored. Action Required: Beginning today, reprogram the body control module (BCM) to the latest calibration using MMDS for all affected CX-3 and MX-5 vehicles in dealer inventory, and when customers bring their vehicles for maintenance, or other service/warranty work. The subject vehicles must not be delivered to customers until the repair of MSP53 is completed. Please inform the customer that the BCM will be reprogrammed to the latest calibration, free of charge. If a vehicle is sold with an open MSP53 your Step 3 PDI warranty claim will be subject to debit.

NHTSA · boletín del fabricante10154528Años modelo 2018–2019Mostrado en inglés original · traducción pendienteVer detalles →
MX-5 (ND) · 2015–
BoletínModeradoSuspensiónNA

Boletín

On certain subject vehicles, it is possible that the panic alarm system may activate while driving, and the horn may sound intermittently and hazard warning lights may flash. The panic alarm concern will stop after cycling the ignition switch off, then on again. No DTCs are stored. Some TPMS wheel sensor IDs on the concerned vehicle or other vehicles nearby may cause the error in the body control module (BCM). Air pressure data transmitted from the wheel sensors may be recognized by the BCM as if the panic button on the remote transmitter has been pressed.

NHTSA · boletín del fabricante10154531Años modelo 2018–2019Mostrado en inglés original · traducción pendienteVer detalles →
MX-5 (ND) · 2015–
BoletínModeradoSuspensiónNA

Boletín

Si un vehículo presenta vibración en la carrocería o temblor del volante mientras se conduce, y la causa raíz se determina como un problema de balanceo de los neumáticos, vuelva a balancear los neumáticos utilizando una máquina de balanceo Hunter GSP9700 o equivalente. Si su concesionario no dispone de una máquina de balanceo GSP9700 o equivalente, subcontrate la reparación del vehículo a otro taller. Para encontrar la ubicación de una GSP9700 cerca de su concesionario, visite el sitio web de Hunter en www.gsp9700.com y haga clic en "Locate a GSP9700 Road Force Balancer" ("Localizar una balanceadora Road Force GSP9700").

NHTSA · boletín del fabricante10154139Años modelo 2019Traducido automáticamente · original: inglésVer detalles →
MX-5 (ND) · 2015–
BoletínModeradoFrenosNA

Boletín

Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.

NHTSA · boletín del fabricante10153227Años modelo 2019Mostrado en inglés original · traducción pendienteVer detalles →
MX-5 (ND) · 2015–
BoletínModeradoHabitáculoNA

Boletín

This information is provided to help address Passenger Airbag Deactivation (PAD) Indicator illumination concerns during vehicle service.

NHTSA · boletín del fabricante10153329Años modelo 2019Mostrado en inglés original · traducción pendienteVer detalles →
MX-5 (ND) · 2015–
BoletínModeradoOtroNA

Boletín

This service bulletin provides information regarding the proper use of the driver's floor mat to avoid anypotential interference with the foot pedals. The following are possible causes of floor mat interference,which can be avoided with proper usage. Floor mat moves forward due to improper installation. Inappropriate floor mat (such as aftermarket, non-factory-equipped, or non-genuine) is used. Floor mat is stacked one on top of another.

NHTSA · boletín del fabricante10153331Años modelo 2019Mostrado en inglés original · traducción pendienteVer detalles →
MX-5 (ND) · 2015–
BoletínModeradoSuspensiónNA

Boletín

As of May 1, 2018, Japan produced vehicles use 17 mm hex lug nuts instead of 21 mm on the same size thread. When installing new lug nuts or the accessory Wheel Lock Set, make sure to use the appropriate part number for the vehicle you are working on. NOTE: The Mazda3 produced in Mexico is not affected.Use the GEPC or the Mazda Accessory web site [MXConnect (dealers.mazdausa.com)] to look up the correct part number for the vehicle you are working on.

NHTSA · boletín del fabricante10153226Años modelo 2018–2019Mostrado en inglés original · traducción pendienteVer detalles →
MX-5 (ND) · 2015–
BoletínModeradoElectrónicaNA

Boletín

Some vehicles may experience the CHECK ENGINE LIGHT ON with DTC P2610 and P2507 stored inmemory after engine start and room fuse 15A (A) removed. P2610:00: Instrument cluster internal engine off timer performance problem P2507:00: PCM battery voltage low input As a past malfunction, the customer will not notice it (no warning light illuminated), but the DTC may be found during a vehicle service. P2507 in this situation is only applicable on 2016 and later models. This is caused by the engine being started 3 or more times after a short duration of engine off (less than 15 seconds) with the room fused removed. NOTE: The odometer will display "F0-002" during transport mode (room fuse 15A removed). Transport mode is canceled when room fuse 15A is installed or the vehicle odometer is more than 12.4mi (20km). Vehicles in dealer inventory with this concern should be repaired using the following repair procedure.

NHTSA · boletín del fabricante10153310Años modelo 2019Mostrado en inglés original · traducción pendienteVer detalles →
MX-5 (ND) · 2015–
BoletínModeradoSuspensiónNA

Boletín

The vehicles listed above are equipped with a push button start/stop ignition system. Unlike previous Mazda models, there is no key cylinder on the steering column. Therefore, the engine cannot be started with the auxiliary key if the room fuse is removed or if the transmitter battery is dead.

NHTSA · boletín del fabricante10153313Años modelo 2019Mostrado en inglés original · traducción pendienteVer detalles →
Anteriores →

Fuentes: NHTSA (Estados Unidos, dominio público), Transport Canada (Licencia de Gobierno Abierto – Canadá), DVSA (Reino Unido, Open Government Licence v3.0), RappelConso y Safety Gate de la UE (Francia, Licence Ouverte 2.0), MLIT (Japón, Licencia de Datos Públicos 1.0) y MOLIT (Corea del Sur, car.go.kr).