Lettura libera · account gratuito per contribuireErede di Anticars (2000)

DodgeDodge Ram

1980– · 5 generazioni · 83 difetti documentati · 4 mercati
Generazioni

I bollettini tecnici (TSB) sono istruzioni di riparazione che i costruttori inviano ai concessionari su problemi noti. Non sono richiami di sicurezza, ma spesso confermano un difetto.

Anno modello
MercatoTuttiNA
Ram IV (2009) · 2018–
BollettinoModeratoMotoreNA

Bollettino

Unable To Install The Left-Hand Power Take-Off (PTO) Unit Upfitters or technicians may experience the following: Unable to install the left-hand PTO unit because of an interference with the fuel line engine bundle. This bulletin involves replacing the fuel line bundle or possibly giving the fuel line bundle to a third party upfitter

NHTSA · bollettino del costruttore11025710Anni modello 2025Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Ram IV (2009) · 2018–
BollettinoModeratoMotoreNA

Bollettino

Engine Block Heater Cord Not Fully Installed From The Factory. Discussion: During Pre-Delivery Inspection (PDI) you will notice that the engine block heater cord is not installed on the engine block.

NHTSA · bollettino del costruttore11018601Anni modello 2025Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Ram IV (2009) · 2008–2024
BollettinoModeratoMotoreNA

Bollettino

Issue involves overheating, running hot, coolant leaks and related symptoms after a Mopar replacement engine has been installed in the vehicle.

NHTSA · bollettino del costruttore10230180Anni modello 2012Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Ram IV (2009) · 2008–2024
BollettinoModeratoMotoreNA

Bollettino

Issue involves overheating, running hot, coolant leaks and related symptoms after a Mopar replacement engine has been installed in the vehicle.

NHTSA · bollettino del costruttore10221594Anni modello 2012Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Ram IV (2009) · 2008–2024
BollettinoModeratoMotoreNA

Bollettino

Valve Cover Gasket It is advised to replace the full valve cover assembly if you are experiencing a valve cover leak Engineering has updated the skirt height of the valve cover to address oil leaks. Replace the valve cover (part # 04893800AI (right side) or 04893799AH (left side)includes valve cover gasket) to ensure proper repair. Please call FCA Redacted Content to facilitate fast track shipment of failed part.

NHTSA · bollettino del costruttore10221366Anni modello 2021Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Ram IV (2009) · 2008–2024
BollettinoModeratoMotoreNA

Bollettino

GASKET, Timing Case Cover, Rear Gear Housing For 2021 Model Year only. If you are replacing the timing gear housing gasket due to an oil leak, please be sure to also replace all outer timing gear housing bolts (PN# 04638665 and 04882109). Do not discard these bolts as engineering will be requesting them to be returned for analysis.

NHTSA · bollettino del costruttore10221373Anni modello 2021Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Ram IV (2009) · 2008–2024
BollettinoModeratoMotoreNA

Bollettino

Customer Complaint May Include Engine Oil Leak Or Consumption

NHTSA · bollettino del costruttore10221277Anni modello 2020Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Ram IV (2009) · 2008–2024
BollettinoModeratoMotoreNA

Bollettino

Small Occasional Oil Leak, Drip, Front Of Engine

NHTSA · bollettino del costruttore10221260Anni modello 2021Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Ram IV (2009) · 2008–2024
BollettinoModeratoMotoreNA

Bollettino

Valve Cover Gasket If you are experiencing a right valve cover leak and plan on replacing only the gasket, the customer may later return for an oil leak. Engineering has updated the skirt height of the valve cover to address oil leaks. Replace the valve cover (part # 04893800AI includes valve cover gasket) to ensure proper repair. Please call FCA Redacted Content if further questions or help is needed with parts retention returns on valve cover assemblies

NHTSA · bollettino del costruttore10214518Anni modello 2021Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Ram IV (2009) · 2008–2024
BollettinoModeratoMotoreNA

Bollettino

Intermittent No Crank No Start This bulletin involves inspecting the ground wire to engine block fastener and replacingif necessary. The customer may comment on the following:A no start and/or intermittent no start condition.

NHTSA · bollettino del costruttore10175549Anni modello 2020Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Ram IV (2009) · 2008–2024
BollettinoModeratoMotoreNA

Bollettino

Intermittent No Crank No Start This bulletin involves inspecting the ground wire to engine block fastener and replacingif necessary. The customer may comment on the following:A no start and/or intermittent no start condition.

NHTSA · bollettino del costruttore10175136Anni modello 2020Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Ram IV (2009) · 2008–2024
BollettinoModeratoMotoreNA

Bollettino

Intermittent No Crank No Start This bulletin involves inspecting the ground wire to engine block fastener and replacingif necessary. The customer may comment on the following:A no start and/or intermittent no start condition.

NHTSA · bollettino del costruttore10174216Anni modello 2020Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Ram III · 2001–2008
BollettinoModeratoMotoreNA

Bollettino

Part Description: 5.7L Long Block Issue Description: This 5.7L Long Block Assembly is compatible with both EGR and Non-EGR applications. An EGR Block-Off Plate (53032739AA) must be ordered when installing this Long Block Assembly in a Non-EGR application. Unless, the EGR Block-Off Plate is being transferred from the old engine.

NHTSA · bollettino del costruttore10229181Anni modello 2003–2008Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Ram IV (2009) · 2008–2024
BollettinoModeratoMotoreNA

Bollettino

Rear Crank Shaft Oil Seal and Retainer Plate For Cummins equipped vehicles only;~ If you are working on a 2016 vehicle ONLY and are replacing the Rear Main Seal for oil leak, replace seal, retainer and gasket using PNs; 05086755A$, 05086754A$, 05015705A$. Remove the retainer with the seal installed. Please do not disturb seal in retainer when removing from engine. Please refer to detailed repair instructions in DealerConnect TechConnect for oil seal retainer replacement.~ Cummins Engineering is currently investigating the root cause of the oil leak concern and would like to analyze these parts. Please contact Chad Eichbrecht at cell (248) 309-2695 to arrange for part return~ If you do not receive a response within 15 minutes, please proceed with normal repair. ~

NHTSA · bollettino del costruttore10228156Anni modello 2016Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Ram IV (2009) · 2008–2024
BollettinoModeratoMotoreNA

Bollettino

Customer Satisfaction Notification T12 VECI Label The Vehicle Emission Control Information (VECI) label on about 120,000 of the above vehicles may be missing emission control information. The VECI label is often used during in-use Inspection and Maintenance (I/M) testing to verify proper emissions related components. Incorrect VECI label information could result in denial of vehicle registration for the vehicle in the state of California. A new VECI label must be installed.

NHTSA · bollettino del costruttore10224875Anni modello 2015Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Ram IV (2009) · 2008–2024
BollettinoModeratoMotoreNA

Bollettino

Cummins Service Engine Replacement This bulletin involves replacing the engine assembly. Remanufactured long block or short block was installed during a prior repair. A new replacement engine will be installed.

NHTSA · bollettino del costruttore10224642Anni modello 2012Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Ram II · 1993–2001
BollettinoModeratoMotoreNA

Bollettino

Service - Four Piece Oil Pan Gasket All Cummins Equipped Vehicles ONLY - The replacement oil pan gasket can be a four piece gasket rather than a single piece gasket. This applies to Cummins 5.9L and 6.7L engines only. Installation: 1. Clean the oil pan T-joints.~ 2. Fill the T-joint between the pan rail/gear housing and pan rail/rear seal retainer with sealant. Use Mopar Silicone Rubber Adhesive Sealant or equivalent. 3. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the oil pan flange.~ 4. The four piece gasket will need to be assembled to make a complete oil pan gasket. 5. Lay the oil pan gasket(s) onto the oil pan flange.~ 6. Ensure the oil pan gasket segment joints are properly aligned. 7. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the top of the oil pan gasket.~ 8. Install the oil pan. Starting from the center and working outward, tighten the oil pan bolts to 28 Nm [21 ft. lbs.].

NHTSA · bollettino del costruttore10223854Anni modello 1998Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Ram IV (2009) · 2008–2024
BollettinoModeratoMotoreNA

Bollettino

Replace Vehicle Emission Certification Information Label This bulletin involves replacing the Vehicle Emission Certification Information (VECI) Label.Owner may be turned away from Inspection and Maintenance (IM) station or fail IM testing because of missing emission components on VECI label. The customer may notice that some info is missing on their VECI labels.is missing. If information is shown in this area, do not replace the label.All vehicles were built with the correct emission components installed and there is no impact on emission performance or drivability.

NHTSA · bollettino del costruttore10223853Anni modello 2015Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Ram III · 2001–2008
BollettinoModeratoMotoreNA

Bollettino

Part Description: 5.7L Long Block Issue Description: This 5.7L Long Block Assembly is compatible with both EGR and Non-EGR applications. An EGR Block-Off Plate (53032739AA) must be ordered when installing this Long Block Assembly in a Non-EGR application. Unless, the EGR Block-Off Plate is being transferred from the old engine.

NHTSA · bollettino del costruttore10223602Anni modello 2003–2008Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Ram IV (2009) · 2008–2024
BollettinoModeratoMotoreNA

Bollettino

Rear Crank Shaft Oil Seal and Retainer Plate For Cummins equipped vehicles only;~ If you are working on a 2016 vehicle ONLY and are replacing the Rear Main Seal for oil leak, replace seal, retainer and gasket using PNs; 05086755A$, 05086754A$, 05015705A$. Remove the retainer with the seal installed. Please do not disturb seal in retainer when removing from engine. Please refer to detailed repair instructions in DealerConnect TechConnect for oil seal retainer replacement.~ Cummins Engineering is currently investigating the root cause of the oil leak concern and would like to analyze these parts. Please contact Chad Eichbrecht at cell (248) 309-2695 to arrange for part return~ If you do not receive a response within 15 minutes, please proceed with normal repair. ~

NHTSA · bollettino del costruttore10220272Anni modello 2016Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Ram IV (2009) · 2008–2024
BollettinoModeratoMotoreNA

Bollettino

Oil Pan 2012-2017 Cummins engines with oil pan leaks, please inspect the shallow area of the oil pan for cracks. If cracks are found, please replace as necessary. Cracks are typically found above the cross member area. Please contact Chad Eichbrecht at cell (248) 309-2695 to arrange for part return or email chad.w.eichbrecht@fcagroup.com If you do not receive a response within 15 minutes, please proceed with normal repair.

NHTSA · bollettino del costruttore10219836Anni modello 2012Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Ram IV (2009) · 2008–2024
BollettinoModeratoMotoreNA

Bollettino

Diesel Exhaust Fluid (DEF) Injector Inspection This bulletin involves pressurizing the Diesel Exhaust Fluid (DEF) injector line to check for a leak during New Vehicle Preparation. The DEF system may not become functional until the vehicle has been driven for 20 miles at one time. This Bulletin will give the steps necessary to ensure DEF system is not leaking. A very small number of vehicles may experience a DEF fluid leak under the vehicle. Upon further investigation the Technician may find that the DEF injector is broke.

NHTSA · bollettino del costruttore10218793Anni modello 2014Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Ram IV (2009) · 2008–2024
BollettinoModeratoMotoreNA

Bollettino

Diesel Exhaust Fluid (DEF) Injector Inspection This bulletin involves pressurizing the Diesel Exhaust Fluid (DEF) injector line to check for a leak during New Vehicle Preparation. The DEF system may not become functional until the vehicle has been driven for 20 miles at one time. This Bulletin will give the steps necessary to ensure DEF system is not leaking. A very small number of vehicles may experience a DEF fluid leak under the vehicle. Upon further investigation the Technician may find that the DEF injector is broke.

NHTSA · bollettino del costruttore10217952Anni modello 2014Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Ram IV (2009) · 2008–2024
BollettinoModeratoMotoreNA

Bollettino

Fluid Leak From Washer Reservoir (X44 Warranty Extension 5 Years/100,000 Miles (160,000 KMS)) This bulletin involves inspecting and/or replacing the washer reservoir. A customer may have a condition where fluid is leaking from the washer reservoir. On further inspection the technician may find cracks in the reservoir by the washer pump pocket.

NHTSA · bollettino del costruttore10216415Anni modello 2011Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Ram IV (2009) · 2008–2024
BollettinoModeratoMotoreNA

Bollettino

Some of the above vehicles equipped with a 6.7L diesel engine may experience a condition where the Noise, Vibration, and Harshness (NVH) engine cover insulates the area on the passenger side of the engine. This could cause engine components under the NVH cover to overheat and possibly ignite.

NHTSA · bollettino del costruttore10215827Anni modello 2013Mostrato in inglese originale · traduzione in attesaVedi dettagli →
Meno recenti →

Fonti: NHTSA (Stati Uniti, pubblico dominio), Transport Canada (Open Government Licence – Canada), DVSA (Regno Unito, Open Government Licence v3.0), RappelConso e Safety Gate UE (Francia, Licence Ouverte 2.0), MLIT (Giappone, Public Data License 1.0) e MOLIT (Corea del Sud, car.go.kr).