Frei lesbar · kostenloses Konto zum MitmachenNachfolger von Anticars (2000)

Mazda MX-5

1989– · 4 generationen · 36 dokumentierte Mängel · 4 Märkte
Generationen

Technische Bulletins (TSB) sind Reparaturanweisungen, die Hersteller ihren Händlern zu bekannten Problemen schicken. Sie sind keine Sicherheitsrückrufe, bestätigen aber oft einen Mangel.

SchweregradAlleMittelGering
Modelljahr
MX-5 (ND) · 2015–
BulletinMittelKarosserieNA

Bulletin

Dieses Bulletin ersetzt die zuvor unten aufgeführten Bulletins. Die Änderungen sind in Rot vermerkt. 09-012/21 13.12.21, 10.06.21 und 27.04.21 BESCHREIBUNG Einige Kunden können folgende Symptome erleben: Die Türverriegelung/Entriegelung funktioniert nicht mit dem Fernschalter des Senders. 1. Die Türverriegelung/Entschlussfunktion funktioniert nicht mit dem Tür- und Entriegelungssensor. 2. Der Motor startet nicht über den Zündschalter. 3. Der Sender arbeitet von selbst. 4. Die Schlüsselbatterie entlädt sich schneller als üblich. 5. Symptome 1-3: Dies kann durch übermäßige Last auf den Fernsender verursacht werden, die elektrische Anschlüsse verformen und einen schlechten Kontakt mit der Batterie schaffen. Um dieses Problem zu beseitigen, wurde die Struktur des Fernsender modifiziert, um die Verformung der elektrischen Anschlüsse zu verringern. Symptom 4-5: Dies kann entstehen, wenn übermäßige Last auf den Fernsender ausgeübt wird, wodurch eine Lücke um die Dichtung entsteht, in die Feuchtigkeit eindringt und die Platine korrodiert, wodurch die Schlüsselbatterie schneller als üblich entlädt wird. Um dieses Problem zu beseitigen, wurde die Dicke der Gehäusewand an der Dichtungsoberfläche erhöht und die Haftfestigkeit der Komponenten verbessert, um Verformungen zu verhindern. REPARATURVERFAHREN Wenn die Batterie defekt ist oder falsch installiert ist, ersetzen Sie die Batterie und/oder installieren Sie sie korrekt. Wenn die Fernbedienung der Energiesparfunktion ausgeschaltet ist und die Batterie korrekt eingebaut ist, ersetzen Sie den defekten Fernsender gemäß den Anweisungen auf MGSS (IMMOBILIZER SYSTEM-RELATED PARTS PROGRAMMING) durch einen modifizierten Sender. HINWEIS: Ersetzen Sie nicht andere Fernsender des Fahrzeugs, wenn keine Probleme auftreten.

NHTSA · Herstellerbulletin11034436Modelljahre 2020Automatisch übersetzt · Original: EnglischDetails ansehen →
MX-5 (ND) · 2015–
BulletinMittelKarosserieNA

Bulletin

Some vehicles may experience one of the following 2 symptoms, even though the windshield is clear. Under certain driving conditions, the Forward Sensing Camera (FSC) may detect a dirty windshield (not clear). NOTE FOR CUSTOMER: The FSC may not work properly under the conditions: The windshield is not clear. The FSC lens is not clear. Driving in heavy rain, dense fog or snow, or into the sun. Driving on a road with no or blurred road lane markings. When the windshield becomes foggy in the winter time or other cold weather conditions and LDWS/HBC warning lights turn on, drive with the defroster on for about 10 minutes. This will help clear the foggy windshield at the FSC.

NHTSA · Herstellerbulletin10185957Modelljahre 2016Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
MX-5 (ND) · 2015–
BulletinMittelKarosserieNA

Bulletin

Some customers may complain of a lack of power under heavy load without any warning lights or DTCs. This concern may be due to a loose or detached hood weatherstrip, which can cause a blockage or restriction in the air intake system.

NHTSA · Herstellerbulletin10165350Modelljahre 2019Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
MX-5 (ND) · 2015–
BulletinMittelKarosserieNA

Bulletin

Some vehicles may exhibit a wind noise (A) from the area between the front (B) and middle (C) roofs when driving at speeds over 37 mph (60 km/h). Due to parts variation, some vehicles may have a poor sealing between the weatherstrips of the front and middle roofs, causing a wind noise. To improve the sealing ability, urethane foam pads have now been installed to the weatherstrips.

NHTSA · Herstellerbulletin10120369Modelljahre 2017Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
MX-5 (ND) · 2015–
BulletinMittelKarosserieNA

Bulletin

Some vehicles may exhibit a wind noise (A) from the area between the front (B) and middle (C) roofs when driving at speeds over 37 mph (60 km/h). Due to parts variation, some vehicles may have a poor sealing between the weatherstrips of the front and middle roofs, causing a wind noise. To improve the sealing ability, urethane foam pads have now been installed to the weatherstrips.

NHTSA · Herstellerbulletin10118478Modelljahre 2017Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
MX-5 (ND) · 2015–
BulletinMittelKarosserieNA

Bulletin

Some vehicles may experience one of the following 2 symptoms, even though the windshield is clear: 1) Lane Departure Warning System (LDWS) warning light turns ON while stopping or driving at a very slow speed. DTC C1001:92 (Poor functioning of Forward Sensing Camera (FSC)) is stored in memory. 2) High Beam Control (HBC) System warning light turns ON while stopping or driving at a very slow speed. DTC C1001:92 (Poor functioning of Forward Sensing Camera (FSC)) is stored in memory. Under certain driving conditions, the Forward Sensing Camera (FSC) may detect a dirty windshield (not clear).

NHTSA · Herstellerbulletin10118126Modelljahre 2016Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
MX-5 (ND) · 2015–
BulletinGeringKarosserieNA

Bulletin

Some customers may complain about any of the following: 1. Infotainment Center Display does not provide the Authorization Code (OTP) during the MyMazda App Connected Vehicle enrollment. 2. Remote function(s) inoperative. Engine Start / Stop Door Lock / Unlock Lights ON / OFF Climate Control 3. MAZDA CONNECT connected vehicle reception strength icon shows "X" or "\".

NHTSA · Herstellerbulletin11011138Modelljahre 2024Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
MX-5 (ND) · 2015–
BulletinGeringKarosserieNA

Bulletin

Some vehicles may experience stains appearing on the hood, roof and/or trunk of the vehicle. This concern is most likely to be found in a cold weather areas just after the RAPGARD is removed at PDI. This may be caused by moisture which has been trapped and condensed between the paint and the RAPGARD. These types of stains can be removed with a heat gun or an infrared drier. If you encounter this concern during PDI, use a heat gun or an infrared drier to apply heat to the affected area to remove the stain(s).

NHTSA · Herstellerbulletin11009639Modelljahre 2024Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
MX-5 (ND) · 2015–
BulletinGeringKarosserieNA

Bulletin

Some customers may complain about any of the following: 1. Infotainment Center Display does not provide the Authorization Code (OTP) during the MyMazda App Connected Vehicle enrollment. 2. Remote function(s) inoperative. Engine Start / Stop Door Lock / Unlock Lights ON / OFF Climate Control

NHTSA · Herstellerbulletin11008573Modelljahre 2024Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
MX-5 (ND) · 2015–
BulletinGeringKarosserieNA

Bulletin

Some customers may complain about any of the following: 1. Infotainment Center Display does not provide the Authorization Code (OTP) during the MyMazda App Connected Vehicle enrollment. 2. Remote function(s) inoperative. Engine Start / Stop Door Lock / Unlock Lights ON / OFF Climate Control

NHTSA · Herstellerbulletin10254190Modelljahre 2024Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
MX-5 (ND) · 2015–
BulletinGeringKarosserieNA

Bulletin

Some customers may complain about any of the following: 1. Infotainment Center Display does not provide the Authorization Code (OTP) during the MyMazda App Connected Vehicle enrollment. 2. Remote function(s) inoperative. Engine Start / Stop, Door Lock / Unlock, Lights ON / OFF, Climate control

NHTSA · Herstellerbulletin10252509Modelljahre 2024Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
MX-5 (ND) · 2015–
BulletinGeringKarosserieNA

Bulletin

In support of the new Mazda MX-5 and CX-3, Mazda will make available for loan on an as-needed basis, a Special Service Tool (SST) to allow for the radar aiming of the blind spot monitoring (BSM) system. The BSM radar aiming is performed whenever the BSM control module, the BSM bracket or the rear bumper is replaced.

NHTSA · Herstellerbulletin10240366Modelljahre 2023Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
MX-5 (ND) · 2015–
BulletinGeringKarosserieNA

Bulletin

Windshield washer fluid change - Factory filled windshield washer fluid has been changed to an ethanol type (yellow color) instead of athe conventional methanol type (blue color). This change is for European compliance Mazda has decided to make the change for all markets.

NHTSA · Herstellerbulletin10186320Modelljahre 2016Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
MX-5 (ND) · 2015–
BulletinGeringKarosserieNA

Bulletin

Remove tool in trunk at pci

NHTSA · Herstellerbulletin10185811Modelljahre 2017Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
MX-5 (ND) · 2015–
BulletinGeringKarosserieNA

Bulletin

Some vehicles may exhibit rust (A) on the front door quarter glass guide (B) where it contacts the door beltline molding (C). The paint on the quarter glass guide gets damaged from vibration when the door is closed and when driving. This concern is caused by the beltline molding contacting the quarter glass guide due to production variances. To correct this concern, a spacer has been attached at the contact area to assure an appropriate clearance between the beltline molding and the quarter glass guide.

NHTSA · Herstellerbulletin10154453Modelljahre 2019Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
MX-5 (ND) · 2015–
BulletinGeringKarosserieNA

Bulletin

Some vehicles may experience stains appearing on the hood, roof and/or trunk of the vehicle. This concern is most likely to be found in cold weather areas just after the RAPGARD is removed at PDI. This may be caused by moisture which has been trapped and condensed between the paint and the RAPGARD. These types of stains can be removed with a heat gun or an infrared drier. If you encounter this concern during PDI, use a heat gun or an infrared drier to apply heat to the affected area to remove the stain(s).

NHTSA · Herstellerbulletin10153338Modelljahre 2019Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
MX-5 (ND) · 2015–
BulletinGeringKarosserieNA

Bulletin

In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealer's responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the "Speedometer Replacement Label". Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazda's vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMO's services, it is possible that the odometer will be set between 10 to 31 miles over the odometer mileage at the time of replacement for both warranty and customer pay repairs. Please make sure that the customer is aware that there may be a slight variance to the odometer, in which case the customer may have to accept the slightly higher mileage. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after-warranty assistance (AWA) or DSA that can be utilized to cover this service expense.

NHTSA · Herstellerbulletin10153339Modelljahre 2019Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
MX-5 (ND) · 2015–
BulletinGeringKarosserieNA

Bulletin

Some customers may complain about SIRIUSXM satellite radio does not show album art, artist biographies or station logos in the center display. This is a normal condition. Album art and artist biographies are not provided by SiriusXM Satellite Radio, a blank white square frame is shown in place of the album art. Note: This information is also available at www.mazdahandsfree.com>FAQ>ENTERTAINMENT - SIRIUSXM. STATION LOGO SIRIUSXM satellite radio hardware is in the Tuner and Amp Unit (TAU). The station logo is not shown in the center display because there is no visual data communication cable between the TAU and the Connectivity Master Unit (CMU). A blank white square frame is shown in place of the station logo. Do NOT perform any repairs for these concerns.

NHTSA · Herstellerbulletin10153294Modelljahre 2019Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
MX-5 (ND) · 2015–
BulletinGeringKarosserieNA

Bulletin

Some vehicles may exhibit the power window(s) not working properly (window does not move or has fallen into the door) and/or making an abnormal noise while operating the power window switch. This may be caused by the cable of the power window motor being damaged from water entry through area (1) of the front beltline molding.To eliminate this concern, the shape of the door glass will be modified during mass production to prevent water entry to the power window regulator.

NHTSA · Herstellerbulletin10153292Modelljahre 2019Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
MX-5 (ND) · 2015–
BulletinGeringKarosserieNA

Bulletin

In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealer's responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the "Speedometer Replacement Label". Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazda's vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMO's services, it is possible that the odometer will be set between 10 to 31 miles over the odometer mileage at the time of replacement for both warranty and customer pay repairs. Please make sure that the customer is aware that there may be a slight variance to the odometer, in which case the customer may have to accept the slightly higher mileage. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after- warranty assistance (AWA) or DSA that can be utilized to cover this service expense.

NHTSA · Herstellerbulletin10148072Modelljahre 2019Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
MX-5 (ND) · 2015–
BulletinGeringKarosserieNA

Bulletin

Some vehicles may experience stains appearing on the hood, roof and/or trunk of the vehicle. This concern is most likely to be found in a cold weather areas just after the RAPGARD is removed at PDI. This may becaused by moisture which has been trapped and condensed between the paint and the RAPGARD. These types of stains can be removed with a heat gun or an infrared drier. If you encounter this concern during PDI, use a heat gun or an infrared drier to apply heat to the affected area to remove the stain(s).

NHTSA · Herstellerbulletin10148071Modelljahre 2019Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
MX-5 (ND) · 2015–
BulletinGeringKarosserieNA

Bulletin

In support of the new Mazda MX-5 and CX-3, Mazda will make available for loan on a "as-needed" basis, a Special Service Tool (SST) to allow for the radar aiming of the blind spot monitoring (BSM) system. The(BSM) radar aiming is performed whenever the (BSM) control module, the (BSM) bracket or the rear bumper is replaced. The tool is available for loan by contacting DAG.

NHTSA · Herstellerbulletin10144324Modelljahre 2019Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
MX-5 (ND) · 2015–
BulletinGeringKarosserieNA

Bulletin

Dealer Rework (DRW) 09 ? 2018 Mazda MX-5 Power Window Switch Concern: On affected vehicles, the driver power window main switch is not correctly assembled to the power window main switch door panel. There are 4 tabs (2 tabs on front side, 2 tabs on rear side) on the power window main switch affixed to the door panel. It is possible that 1 or 2 of the tabs are not locked, and there is a chance the switch will drop slightly when the power outer mirror switch is pushed.When the power window main switch part is assembled to the driver-side door trim by a jig in production, the power window main switch could have been unintentionally pushed vertically due to the jig misalignment.

NHTSA · Herstellerbulletin10134937Modelljahre 2018Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
MX-5 (ND) · 2015–
BulletinGeringKarosserieNA

Bulletin

Some vehicles with Blind Spot Monitoring (BSM) may experience the following conditions (similar to when the BSM control modules detect dirt on the rear bumper surface): DTC U1A4B:97 - Radar sensor sensitivity temporarily decreases depending on various external and environmental factors (blind spot monitoring (BSM) control module (RH)), DTC U3000:97 - Radar sensor sensitivity temporarily decreases depending on various external and environmental factors (blind spot monitoring (BSM) control module (LH)), The BSM turns ?OFF? and the BSM OFF indicator turns ?ON? in the instrument cluster while driving, The BSM will not turn on again during the drive cycle, After cycling the ignition switch off and on again, the BSM operates normally, DTC U1A4B:97 or U3000:97 is stored in memory. To correct this problem, the control logic of the BSM control modules has been changed.

NHTSA · Herstellerbulletin10120383Modelljahre 2016Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
MX-5 (ND) · 2015–
BulletinGeringKarosserieNA

Bulletin

Some vehicles may exhibit a squeak noise at the rear beltline when the door glass moves up and/or down. This concern happens especially when the door glass is wet with moisture or after a car wash. This is caused by stick-slip noise occurring at the contact surfaces between the door glass and the weather strip. With repeated moving up and down, the anti-noise paint on the weather strip peels off. To prevent the stick-slip noise, a polyester film has been attached at the applicable location of the weatherstrip.

NHTSA · Herstellerbulletin10120357Modelljahre 2016Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Ältere →

Quellen: NHTSA (USA, gemeinfrei), Transport Canada (Open Government Licence – Canada), DVSA (Vereinigtes Königreich, Open Government Licence v3.0), RappelConso und EU-Safety-Gate (Frankreich, Licence Ouverte 2.0), MLIT (Japan, Public Data License 1.0) und MOLIT (Südkorea, car.go.kr).