Bulletin
Ldws and hbc warning lights on and dtc c1001:92
🔔 Kostenloses Konto anlegen und Benachrichtigungen zu Mazda MX-5 (alle generationen) erhalten
Technische Bulletins (TSB) sind Reparaturanweisungen, die Hersteller ihren Händlern zu bekannten Problemen schicken. Sie sind keine Sicherheitsrückrufe, bestätigen aber oft einen Mangel.
Ldws and hbc warning lights on and dtc c1001:92
If you experience issues with the current version of ID's such as missing tools or modules not showing after completing a network test, be advised that we are aware of these issues and are working to resolve them. As a counter measure, it is advised that you un-install ids and re-install version 103.00 and "do not update" until further notice.
Some vehicles may experience the CHECK ENGINE LIGHT ON with DTC P2610 and P2507 stored inmemory after engine start and room fuse 15A (A) removed. P2610:00: Instrument cluster internal engine off timer performance problem P2507:00: PCM battery voltage low input As a past malfunction, the customer will not notice it (no warning light illuminated), but the DTC may be found during a vehicle service. P2507 in this situation is only applicable on 2016 and later models. This is caused by the engine being started 3 or more times after a short duration of engine off (less than 15 seconds) with the room fused removed. NOTE: The odometer will display "F0-002" during transport mode (room fuse 15A removed). Transport mode is canceled when room fuse 15A is installed or the vehicle odometer is more than 12.4mi (20km). Vehicles in dealer inventory with this concern should be repaired using the following repair procedure.
If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Aftermarket devices may be the cause of the electrical concern. Ask the customer if any aftermarket devices have been installed. Below are a couple of examples of unusual electrical concerns caused by aftermarket devices.
Some customers may complain about: Intermittent engine no start, Instrument cluster red security indicator light ON, Engine Start/Start Button Amber indicator, light flashing, Battery discharge, Electrical relay buzzing noise.This may be caused by: A key in a purse near a cell phone. The cell phone radio waves may interrupt the immobilizer system. An aftermarket cell phone charger. The charger may produce electrical noise that interrupts the immobilizer system. An aftermarket GPS tracker. Some aftermarket devices that are wired to the vehicles?s wiring harness may create unusual electrical symptoms.
Some customers may complain about the following: Engine no start. A blurry rear view monitor display. This may be caused by an aftermarket accessory device. Some aftermarket electrical devices (e.g., an accessory cell phone charger, GPS tracker...) may create excessive electrical noise. The noise may interrupt some of the vehicle electrical systems. Below are a few examples of an aftermarket cell phone charger and GPS tracker that are interrupting the vehicle electrical systems.
Some 2018 vehicles built after January 1, 2018 and equipped with Navigation may exhibit one of these concerns after the user inputs an address: A screen pops up that says "House number not found." After the user selects OK, the system finds the address or a nearby address.Instead of finding the correct address number the system adds a digit to the end of the number. Example: You enter 151 and the system comes back with 1510, 1511, 1515, 1516, etc. This only occurs with MAZDA CONNECT software version 59.00.532 or 59.00.540, which started being installed into vehicles in January 2018. The concern can be eliminated by installing MAZDA CONNECT software version 59.00.545 now available on MGSS.
2017 MX-5 Battery Discharging Concern Special Service Program (SSP) B5 - Mazda Motor Corporation has decided to conduct a Special Service Program (SSP) on certain 2017 MX-5 vehicles equipped with retractable fastback hardtop, and built from October 4, 2016 through May 9, 2017. On affected MX-5 vehicles, if the vehicle is turned off while the Cruise Control is ON, the microcomputer may not go into sleep mode, allowing an electric current to continue to flow. With this condition, if the vehicle is left unused for an extended period of time (Approximately 10+ days), the battery may discharge, resulting in a no start condition. There are 5,125 vehicles in the United States affected by this SSP.
Some customers may complain about engine no start due to the battery being discharged. This may becaused by a software error with the speedometer which allows a dark current of 80 mA can continue to flowafter the ignition is turned off. If the vehicle is not used for more than a week and left in this condition, the battery will discharge. NOTE: A normal dark current value is about 25 45 mA. Condition where dark current of 80mA occurs: If the ignition is switched OFF while the Cruise Control is ON (one of the Cruise Control indicators is ON in the MID), the microcomputer does not shift into the sleep mode and an operation current of 80 mA will continue to flow. NOTE: If the ignition is switched OFF after Cruise Control is turned OFF, this concern does not occur. Cruise Control indicators is ON Instrument Cluster with MID To correct this concern, the software of the instrument cluster has been changed.
Some 2018 vehicles built after January 1, 2018 and equipped with Navigation may exhibit one of these concerns after the user inputs an address: A screen pops up that says "House number not found." After the user selects OK, the system finds the address or a nearby address.Instead of finding the correct address number the system adds a digit to the end of the number. Example: You enter 151 and the system comes back with 1510, 1511, 1515, 1516, etc.This only occurs with MAZDA CONNECT software version 59.00.540, which started being installed into vehicles in January 2018. The concern can be eliminated by installing MAZDA CONNECT software version 59.00.504.
Some customers may complain about engine no start due to the battery discharged. This may be caused by a software error with the speedometer, a dark current of 80 mA can continue to flow after the ignition is turned off. If the vehicle is not used for more than a week and left in this condition, the battery will discharge.
Some vehicles may experience the check engine light on with dtc p2610 and p2507 stored in memory after engine start and room fuse 15a (a) removed. P2610:00: Instrument cluster internal engine off timer performance problem p2507:00: Pcm battery voltage low input as a past malfunction, the customer will not notice it (no warning light illuminated), but the dtc may be found during a vehicle service. P2507 in this situation is only applicable on 2016 and later models. This is caused by the engine being started 3 or more times after a short duration of engine off (less than 15 seconds) with the room fused removed.
If you encounter a vehicle with dtc p0137 (circuit low input), check the rear harness at the red circled area in the following diagram. If an aftermarket alarm system is installed, the rear harness might have received damage from electro-tap connectors (a) or to the protector tube (b). This damage is not covered under warranty.
If a customer has a vehicle communication related error on their app, perform the following: Disconnect the battery or unplug the module for at least 10 seconds.Reconnect the battery, wait 60 seconds and then have the customer try the app again.If the vehicle starts, order module 0000-8f-z80a.Note: There is a limited supply of the module at this time, therefore only use this part for this specific condition.Due to the limited supply, make sure you were shipped the a level part and not the original part before installing the part.Install the module and program it per mms programming instructions.Instruct the customer to update their account with the new module information, otherwise the mms will not work from the app.
Mazda connect software version 55.00.760 is now available on ms3. Use this version for all mazda connect updates, including open ssp98 vehicles. If ssp98 is closed, use tsb 09-024/16 to repair the vehicles.Click on "ids/infotainment", then "mazda connect updates" to download it. Update your usb drives according to the instructions in tsb 09-024/16.Also make sure to select "all files" for "save as type:". If left as "compressed (zipped) folder," the file will be saved as a ".Zip" no matter what you use as an extension.Attn: Technicians - be sure to document the software version installed on the repair order and inform your warranty administrator to provide the information in the repair text of the warranty claim.Mazda is working to make further improvements to the mazda connect infotainment system software, and may issue future software updates to improve system operation and performance. Software version updates can be found on ms3.
Some customers may experience a Connected Vehicle failure. The MyMazda App may display an Error Code. This document provides Error Code description and recovery information to assist with repairs.
Some customers may experience a Telematics Malfunction message in the instrument cluster with DTC U3000:00-TCU (Emergency call unit/telematics communication unit internal malfunction) or U3000:04-TCU (Telematics communication unit internal malfunction) stored in memory. This is caused by improper control software of the telematics communication unit (TCU). To eliminate this concern, the control software of the TCU has been modified.
Motorstart-/Stoppverfahren mit entfernter Raumsicherung
Some vehicles may experience a lack of power and the check engine light on with DTC P061B:00 stored in PCM memory under one of the following conditions (A or B). DTC P061B:00 - [PCM] Internal control module torque calculation performance problem. Due to an improper control logic of the PCM, the engine torque calculation error detection is too sensitive. To eliminate this concern, the PCM software has been modified.
After Pandora V7.0 was released on March 7th, the following problems have been found on vehicle with MAZDA CONNECT. Navigation voice guidance will skip and cut out losing many words.Pandora will suddenly disconnect and MAZDA CONNECT will revert to the previously used source. If you encounter a vehicle with these issues, DO NOT attempt any repairs on the vehicle. There is nothing wrong with the vehicle. This is an issue with the Pandora APP. Have the customer contact Pandora at pandora-support@pandora.com. NOTE: If the Pandora APP works on the customer's phone, they can stream Pandora using Bluetooth.
Mazda connect software version 59.00.441 available - Important Update. Used the Labor Op Code in the TSB to update these vehicles with a customer concern until an updated TSB is published.
New IDs software version 102.00 and Update 102.01 is now available on MS3 IDs update 102.00 and 102.01 is now available on MS3 under the "IDs/Infotainment" tab.
On the 2019 Mazda3 (BP) and and all 2020 Mazda vehicles (except CX-3), the CR2032 button cell battery is required for the new type remote transmitter. If it is mistakenly replaced with the conventional CR2025 used in the previous type remote transmitter, it may cause a malfunction. Verify the button cell battery type before replacing it.
Customers having MAZDA CONNECT concerns should have their vehicle repaired using the following repair procedure. NOTE: Before proceeding: Confirm that the Connectivity Master Unit (CMU) is updated to the latest software version. Go to MGSS - Infotainment - MAZDA CONNECT Updates, Confirm that the customers device is updated to the latest software version. Apple Carplay/Android Auto FAQ, go to SA-001/19.
Some vehicles may experience a lack of power and the check engine light on with DTC P061B:00 stored in PCM memory under one of the following conditions (A or B). DTC P061B:00 - [PCM] Internal control module torque calculation performance problem. Due to an improper control logic of the PCM, the engine torque calculation error detection is too sensitive. To eliminate this concern, the PCM software has been modified.
Quellen: NHTSA (USA, gemeinfrei), Transport Canada (Open Government Licence – Canada), DVSA (Vereinigtes Königreich, Open Government Licence v3.0), RappelConso und EU-Safety-Gate (Frankreich, Licence Ouverte 2.0), MLIT (Japan, Public Data License 1.0) und MOLIT (Südkorea, car.go.kr).