Technische Bulletins (TSB) sind Reparaturanweisungen, die Hersteller ihren Händlern zu bekannten Problemen schicken. Sie sind keine Sicherheitsrückrufe, bestätigen aber oft einen Mangel.
Some vehicles may exhibit the inner cloth (A) falling down at the rear end causing a poor appearance and obstructing the view of the back window. This is caused by the J-hook binding holding the inner cloth coming loose during the opening/closing of the convertible top, from vibration during driving or from high ambient temperatures. To correct the problem, two top-protector clips have been additionally installed to both side edges of the J-hook to prevent the J-hook from loosening and separating.
Due to a database error discovered with IDS 114.00-114.02 release (which affects Recall 3719F), it will be necessary to uninstall IDS 114 and install IDS 113.00 and 113.06 update. The Recall can be performed after removing IDS 114 and installing IDS 113. This SA will be updated when more information is available.
On May 1, 2018, Japan produced vehicles starting using 17 mm hex lug nuts instead of 21 mm on the same size thread. When installing the accessory locking lug nuts, make sure to use the appropriate part number for the vehicle you are working on.
In Unterstützung der neuen MRT-Verteilung wird Mazda ab März 2019 ein neues Diagnosegerät zur Dual-Purpose-Lecksuche an die Händler ausliefern. Schulungsvideos werden in Kürze auf MGSS veröffentlicht, und die Verfahren im Werkstatthandbuch werden nach und nach überarbeitet.
This service bulletin provides information regarding the proper use of the driver's floor mat to avoid anypotential interference with the foot pedals. The following are possible causes of floor mat interference,which can be avoided with proper usage. Floor mat moves forward due to improper installation. Inappropriate floor mat (such as aftermarket, non-factory-equipped, or non-genuine) is used. Floor mat is stacked one on top of another.
On May 1, 2018, Japan produced vehicles starting using 17 mm hex lug nuts instead of 21 mm on the same size thread. When installing the accessory locking lug nuts, make sure to use the appropriate part number for the vehicle you are working on.
Some customers may complain that the the middle headliner looks loose at the center rear. This is caused by parts variation. To correct the concern, an additional fastener can be installed in the headliner.
Some vehicles may experience poor a/c performance due to a slow refrigerant leak from the o-ring groove on the cooler pipe (high pressure side) at the expansion valve.
Some vehicles may experience poor a/c performance due to a slow refrigerant leak from the o-ring groove on the cooler pipe (high pressure side) at the expansion valve.
Some vehicles may exhibit the inner cloth (a) falling down at the rear end causing a poor appearance and obstructing the view of the back window. This is caused by the j-hook binding holding the inner cloth coming loose during the opening/closing of the con-vertible top, from vibration during driving or from high ambient temperatures.To correct the problem, two top-protector clips have been additionally installed to both side edges of the j-hook to prevent the j-hook from loosening and separating.
Some vehicles may exhibit the inner cloth (a) falling down at the rear end causing a poor appearance and obstructing the view of the back window.This is caused by the j-hook binding holding the inner cloth coming loose during the opening/closing of the con-vertible top, from vibration during driving or from high ambient temperatures.This is caused by the j-hook binding holding the inner cloth coming loose during the opening/closing of the con-vertible top, from vibration during driving or from high ambient temperatures.To correct the problem, two top-protector clips have been additionally installed to both side edges of the j-hook to prevent the j-hook from loosening and separating.
Workshop manual evap system leak inspection using the m-mds has been discontinued for some models. Instead, the workshop manual evap system leak inspection using evap leak tester will be used to troubleshoot evap system leaks.
Some vehicles may exhibit the inner cloth (a) falling down at the rear end causing a poor appearance and obstructing the view of the back window. This is caused by the j-hook binding holding the inner cloth coming loose during the opening/closing of the con-vertible top, from vibration during driving or from high ambient temperatures.To correct the problem, two top-protector clips have been additionally installed to both side edges of the j-hook to prevent the j-hook from loosening and separating.
When the Telematics Control Unit (TCU) replacement is necessary due to a failure, use MDARS to activate the new TCU after replacement. Use the information in this service alert to initialize the new TCU until the procedure on MGSS is updated.
When the Telematics Control Unit (TCU) replacement is necessary due to a failure, use MDARS to activate the new TCU after replacement. Use the information in this service alert to initialize the new TCU until the procedure on MGSS is updated.
Quellen: NHTSA (USA, gemeinfrei), Transport Canada (Open Government Licence – Canada), DVSA (Vereinigtes Königreich, Open Government Licence v3.0), RappelConso und EU-Safety-Gate (Frankreich, Licence Ouverte 2.0), MLIT (Japan, Public Data License 1.0) und MOLIT (Südkorea, car.go.kr).