Los boletines técnicos (TSB) son instrucciones de reparación que los fabricantes envían a sus concesionarios sobre problemas conocidos. No son llamadas a revisión de seguridad, pero a menudo confirman una avería.
Some vehicles listed in the Model statement above may exhibit a no crank/no start condition where the customer cannot start their vehicle. The vehicle may also exhibit a "No Key Detected" message displayed on the instrument panel cluster (IPC), and no key fob works in the back up slot. The remote keyless entry (RKE) functionality will work to lock/unlock the vehicle.
NHTSA · boletín del fabricante11028830Años modelo 2025Mostrado en inglés original · traducción pendienteVer detalles →
Some 2022 Explorer vehicles equipped with a 3.3L full hybrid electric vehicle (FHEV) engine and built on 12-Jul-2022 and through 31-Oct-2022 may exhibit a coolant leak at the high voltage (HV) battery coolant cooler outlet hose. This may be due to the HV battery coolant cooler outlet hose contacting the bottom pulley of the accessory drive belt tensioner. To correct the condition, follow the Service Procedure to replace the damaged hose and install a cable tie.
NHTSA · boletín del fabricante10239631Años modelo 2022Mostrado en inglés original · traducción pendienteVer detalles →
Some 2018 Explorer/Police Interceptor Utility vehicles equipped with Police, Base 100A, or XLT 200A package trim levels (Type 1 analog cluster in the Owner's Manual) built on 08-May-2018 and through 05-Aug-2018 may exhibit a parasitic battery drain of approximately 250 milliamps with the instrument panel cluster (IPC) possibly staying awake with the key off. This may result in a no crank/no start/discharged battery condition. To resolve the concern, reprogram the IPC using the latest software level using the Integrated Diagnostic System (IDS). Make sure the vehicle is connected to a battery charger. For claiming, use causal part 10849 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA · boletín del fabricante10216541Años modelo 2018Mostrado en inglés original · traducción pendienteVer detalles →
Some 2017-2021 Ford and Lincoln vehicles equipped with 3.3L, 3.5L EcoBoost, or 5.0L engines may exhibit stalling, lack of power, low fuel rail pressure and/or DTCs P0087 or P008A after a repair was made that required the removal of the fuel line that connects the high-pressure fuel pump to the port injection rail, such as injector replacements or base engine repairs. This line must be installed in the correct orientation as it has an internal one-way check valve. To determine if the fuel line has been installed improperly, look at the position of the Oetiker clamp (stainless band clamped around the black fuel line). The clamp holds the one-way check valve in place and should be located closest to the end connected to the port injection rail. If the clamp is not closest to the port injection rail, remove and reinstall the line in the proper orientation.
NHTSA · boletín del fabricante10201579Años modelo 2020Mostrado en inglés original · traducción pendienteVer detalles →
Ford Motor Company ha determinado que ciertos vehículos Ford F-150, F-Super Duty y Explorer del año modelo 2020, equipados con una cámara de respaldo instalada de fábrica por Ford, no cumplen con la Norma Federal de Seguridad de Vehículos Motorizados número 111 - Visibilidad trasera. Comuníquese con su concesionario Ford local para programar una fecha de servicio para realizar la reparación del llamado a revisión. Consulte la comunicación adjunta de Ford para obtener información adicional. Altec no puede completar esta reparación. Todo el trabajo debe ser realizado por un concesionario Ford autorizado.
Some 2020 Explorer Base vehicles equipped with blind spot information system (BLIS) and class III trailer tow package 52T may exhibit an illuminated BLIS indicator and/or inability to turn the BLIS system off. This may be due to the software in the instrument panel cluster (IPC). To correct the condition, perform a programmable module installation (PMI) on the IPC using the appropriate Ford diagnostic scan tool. For claiming, use causal part 10849 and applicable labor times from Section 10 in the Service Labor Time Standards (SLTS) Manual.
NHTSA · boletín del fabricante10184627Años modelo 2020Mostrado en inglés original · traducción pendienteVer detalles →
Algunos vehículos Ford y Lincoln de 2017-2020 equipados con una TCU pueden presentar funciones remotas inoperativas a través de la aplicación móvil Ford Pass/Lincoln Way, autorización de usuario incompleta y/o ausencia del número de serie electrónico (ESN) del módem en pantalla. Para corregir esta condición antes de programar, retire el fusible de la TCU durante 5 minutos y vuelva a instalarlo. Elimine todos los archivos de sesión anteriores del vehículo. Verifique que el número de serie electrónico (ESN) ahora se muestre. Inicie una nueva sesión de IDS/FDRS. Programe la TCU a la versión más reciente de IDS/FDRS. Asegúrese de estar conectado a internet antes de volver a probar. Si el problema persiste, siga los procedimientos de diagnóstico normales del Manual de Taller (WSM), Sección 415-00. Consulte la página principal de PTS OASIS para identificar la versión de la TCU. Para la reclamación, utilice la pieza causal 14G229 y las operaciones de mano de obra aplicables de la Sección 10 del Manual de Tiempos Estándar de Mano de Obra de Servicio (SLTS).
Some 2020 Explorer/Aviator vehicles may exhibit a rattle type noise originating from the exhaust flexible pipe. This may be due to the natural harmonic frequency of the pipe. To correct the condition, follow the Service Procedure to install a worm gear clamp over the exhaust flexible pipe.
NHTSA · boletín del fabricante10179152Años modelo 2020Mostrado en inglés original · traducción pendienteVer detalles →
Some 2020 Explorer/Aviator vehicles may exhibit a rattle type noise originating from the exhaust flexible pipe. This may be due to the natural harmonic frequency of the pipe. To correct the condition, follow the Service Procedure to install a worm gear clamp over the exhaust flexible pipe.
NHTSA · boletín del fabricante10177124Años modelo 2020Mostrado en inglés original · traducción pendienteVer detalles →
Some 2017-2020 Model year vehicles equipped with 3.3L, 3.5L EcoBoost, or 5.0L engines may exhibit stalling, lack of power, low fuel rail pressure and/or DTCs P0087 or P008A after a repair was made that required the removal of the fuel line that connects the high-pressure fuel pump to the port injection rail, such as injector replacements or base engine repairs. This line must be installed in the correct orientation as it has an internal one-way check valve. To determine if the fuel line has been installed improperly, look at the position of the Oetiker clamp (stainless band clamped around the black fuel line). The clamp holds the one-way check valve in place and should be located closest to the end connected to the port injection rail. If the clamp is not closest to the port injection rail, remove and reinstall the line in the proper orientation.
NHTSA · boletín del fabricante10176110Años modelo 2020Mostrado en inglés original · traducción pendienteVer detalles →
Some 2020 Ford and Lincoln vehicles may exhibit a symptom of no ability to schedule a remote start event using the FordPass or Lincolnway app. If only the scheduling portion of the remote start system is not functioning, please ensure that the latest level of SYNC software has been installed. If the remote start system is not functioning using the key fob and/or the on-demand remote start function from FordPass or Lincolnway application, refer to Workshop Manual (WSM), Section 303-06 for further diagnosis.
NHTSA · boletín del fabricante10176119Años modelo 2020Mostrado en inglés original · traducción pendienteVer detalles →
Some 2020 Explorer, Aviator, Ecosport, Mustang, Escape or Corsair may have a symptom of no ability to schedule a remote start event using the Fordpass or Lincolnway app. This may be due to the current level SYNC software installed. To correct this condition, program the SYNC module utilizing section 415 of the workshop manual. If no update is available or the problem persists after programming, verify that the Fordpass or Lincolnway app is activated properly as per the owners guide. For claiming, use causal part 14G371 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA · boletín del fabricante10169913Años modelo 2020Mostrado en inglés original · traducción pendienteVer detalles →
Some 2018 Explorer/Police Interceptor Utility vehicles equipped with Police, Base 100A, or XLT 200A package trim levels (Type 1 analog cluster in the Owner's Manual) built on 08-May-2018 and through 05-Aug-2018 may exhibit a parasitic battery drain of approximately 250 milliamps with the instrument panel cluster (IPC) possibly staying awake with the key off. This may result in a no crank/no start/discharged battery condition. To resolve the concern, reprogram the IPC using the latest software level of the appropriate Ford diagnostic scan tool. Make sure the vehicle is connected to a battery charger. For claiming, use causal part 10849 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA · boletín del fabricante10149757Años modelo 2018Mostrado en inglés original · traducción pendienteVer detalles →
Some 2018 Explorer/Police Interceptor Utility vehicles equipped with Police, Base 100A, or XLT 200A package trim levels (Type 1 analog cluster in the Owner's Manual) built on 08-May-2018 and through 05-Aug-2018 may exhibit a parasitic battery drain of approximately 250 milliamps with the instrument panel cluster (IPC) possibly staying awake with the key off. This may result in a no crank/no start/discharged battery condition. To resolve the concern, reprogram the IPC using the latest software level of the appropriate Ford diagnostic scan tool. For claiming, use causal part 10849 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
NHTSA · boletín del fabricante10144946Años modelo 2018Mostrado en inglés original · traducción pendienteVer detalles →
Algunos vehículos Ford y Lincoln de 2018 equipados con una TCU pueden presentar funciones remotas inoperativas a través de la aplicación móvil Ford Pass/Lincoln Way, autorización de usuario incompleta y/o el código de diagnóstico (DTC) U0198 del módulo de interfaz de protocolos de accesorios (APIM), o no mostrar el número de serie electrónico (ESN) del módem. Para corregir esta condición, retire el fusible de la TCU durante 5 minutos y luego vuelva a instalarlo. Asegúrese de estar conectado a internet antes de volver a probar. Si la anomalía persiste, siga los diagnósticos normales del Manual de Taller (WSM), Sección 415-00. Consulte la página principal de PTS OASIS para identificar la versión de la TCU. Para la reclamación, utilice la pieza causal 14G229.
Some 2016-2017 Ford and Lincoln vehicles with SYNC 3 may exhibit an intermittent blue or black screen. Check for SYNC software update under the OASIS Tab SYNC selection. If update is available refer to WSM, Section 415-00 and update APIM software. After Installation Complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.
NHTSA · boletín del fabricante10119678Años modelo 2017Mostrado en inglés original · traducción pendienteVer detalles →
Algunos vehículos Ford/Lincoln 2016-2017 con SYNC 3 pueden presentar una pantalla en blanco intermitente. Verifique si hay una actualización de software de SYNC en la pestaña OASIS, en la selección SYNC. Si hay una actualización disponible, consulte el WSM, Sección 415-00, y actualice el software del APIM. Durante el proceso de actualización, la barra de estado de SYNC muestra "Actualizando el software del sistema" durante aproximadamente 30 minutos. Cuando aparezca la ventana emergente "Installation Complete", retire la memoria USB e insértela en la herramienta IDS para actualizar la base de datos de Ford. Realice un ciclo completo de encendido apagando la llave durante 5 minutos, lo cual es fundamental para una instalación exitosa. Si no hay actualizaciones disponibles o la pantalla en blanco persiste después de una actualización, consulte el WSM, Sección 415-00, para el diagnóstico, o el GSB de pantalla en blanco intermitente de SYNC 3 para obtener sugerencias. Para la reclamación, utilice la pieza causal 14G371 y las operaciones de mano de obra aplicables en la sección 10 del manual SLTS.
Ford: On some 2010 models there may be many symptoms such as an engine rattle, malfunction light, lack of power, no start, and runs rough. *rm updated 8/9/11. *pe
NHTSA · boletín del fabricante10037082Años modelo 2010Mostrado en inglés original · traducción pendienteVer detalles →
An intermittent no start and/or malfunction indicator lamp (mil) on with diagnostic trouble codes (dtc's) p1233, p1234, p1235, p1236, p1237 or p1238. *tt
NHTSA · boletín del fabricante10007389Años modelo 2004Mostrado en inglés original · traducción pendienteVer detalles →
Fuentes: NHTSA (Estados Unidos, dominio público), Transport Canada (Licencia de Gobierno Abierto – Canadá), DVSA (Reino Unido, Open Government Licence v3.0), RappelConso y Safety Gate de la UE (Francia, Licence Ouverte 2.0), MLIT (Japón, Licencia de Datos Públicos 1.0) y MOLIT (Corea del Sur, car.go.kr).