Lecture libre · compte gratuit pour contribuerSuccesseur d’Anticars (2000)

Mini Hatch

2001– · 5 générations · 50 défauts documentés · 3 marchés
Générations

Les bulletins techniques (TSB) sont des instructions de réparation que les constructeurs envoient à leurs concessionnaires sur des problèmes connus. Ce ne sont pas des rappels de sécurité, mais ils confirment souvent un défaut.

Année modèle
MarchéTousEUUKNA
Hatch III · 2013–2024
BulletinModéréBoîteNA

Bulletin

"B38, B46, and B48 Engines: Engine Noise, Drivability Complaints, and Various DME Faults. The vehicle exhibits one the following complaints: z Noise from the lower engine area, described as a high-pitched whine z Loss of power when idling z At a higher engine speed (above 3,000 rpm), a brief decrease in the engine speed can be felt. z Extended cranking before the engine will start z The customer notices an increased level of ""free play"" in the clutch pedal when changing gears. z The clutch pedal remains depressed, and will not return to the disengaged position. z Emergency operation is active, with one or more of the faults listed below. One or more of the following faults may be stored in the vehicle: z 160020 Crankshaft sensor, signal: implausible z 180001 Catalytic converter: efficiency too low z 200D0C Powertrain, safety function: bus signal rpm reduction implausible z 11A002 Fuel high pressure, plausibility: Pressure too low z 1F054D Powertrain, safety function: powertrain reduced power, DSC-signal implausible Note: If additional faults are found in the DME memory (e.g., misfire, camshaft sensor, knock sensor, etc.), then those faults will be the primary focus of the diagnosis using the test plans provided for those faults. ""FC 120408 Boost pressure control: Shut-down as a consecutive reaction"" is only a result of the component fault and is not the primary reason for the complaint or https://www.minitis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/286...1/4/2016 Page 2 of 2 illumination of the engine malfunction warning."

NHTSA · bulletin constructeur10147907Années modèle 2016Affiché en anglais d’origine · traduction en attenteVoir le détail →
Hatch III · 2013–2024
BulletinModéréBoîteNA

Bulletin

"B38, B46, and B48 Engines: Clutch Operation, Engine Noise, and Drivability Complaints. The vehicle exhibits one the following complaints: z The customer notices an increased level of ""free play"" in the clutch pedal when changing gears. z The clutch pedal remains depressed and will not return to the disengaged position. z Noise from the lower engine area described as a high-pitched whine z Loss of power when idling z At a higher engine speed (above 3,000 rpm), a brief decrease in the engine speed can be felt. z Extended cranking before the engine will start z Emergency operation is active with one or more of the faults listed below. One or more of the following faults may be stored in the vehicle: z 160020 Crankshaft sensor, signal: implausible z 180001 Catalytic converter: efficiency too low z 200D0C Powertrain, safety function: bus signal rpm reduction implausible z 11A002 Fuel high pressure, plausibility: Pressure too low z 1F054D Powertrain, safety function: powertrain reduced power, DSC-signal implausible Note: If additional faults are found in the DME memory (e.g., misfire, camshaft sensor, knock sensor, etc.), then those faults will be the primary focus of the diagnosis using the test plans provided for those faults. ""FC 120408 Boost pressure control: Shut-down as a consecutive reaction"" is only a result of the component fault and is not the primary reason for the complaint or illumination of the engine malfunction warning."

NHTSA · bulletin constructeur10147908Années modèle 2016Affiché en anglais d’origine · traduction en attenteVoir le détail →
Hatch III · 2013–2024
BulletinModéréBoîteNA

Bulletin

"?SI M12 04 15 Engine Electrical Systems June 2015 Technical Service This Service Information bulletin supersedes SI M12 04 15 dated March 2015. designates changes to this revision SUBJECT B38, B46, and B48 Engines: Engine Noise, Drivability Complaints, and Various DME Faults. The vehicle exhibits one the following complaints: ? Noise from the lower engine area, described as a high-pitched whine ? Loss of power when idling ? At a higher engine speed (above 3,000 rpm), a brief decrease in the engine speed can be felt. ? Extended cranking before the engine will start ? The customer notices an increased level of ""free play"" in the clutch pedal when changing gears. ? The clutch pedal remains depressed, and will not return to the disengaged position. ? Emergency operation is active, with one or more of the faults listed below. Faults stored in the vehicle: ? 160020 Crankshaft sensor, signal: implausible ? 180001 Catalytic converter: efficiency too low ? 200D0C Powertrain, safety function: bus signal rpm reduction implausible ? 11A002 Fuel high pressure, plausibility: Pressure too low ? 1F054D Powertrain, safety function: powertrain reduced power, DSC-signal implausible? 120408 Boost pressure control: Shut-down as a consecutive reaction"

NHTSA · bulletin constructeur10147739Années modèle 2016Affiché en anglais d’origine · traduction en attenteVoir le détail →
Hatch III · 2013–2024
BulletinModéréBoîteNA

Bulletin

"B38, B46 and B48 Engines: Drivability Complaints with Crankshaft Sensor Fault. The vehicle exhibits one of the following complaints: ? Loss of power when idling ? At a higher engine speed (above 3,000 rpm), a brief decrease in the engine speed can be felt. ? Extended cranking before the engine will start ? The customer notices an increased level of ""free play"" in the clutch pedal when changing gears. ? The clutch pedal remains depressed and will not return to the disengaged position. ? Emergency operation is active with one or more of the faults listed below. Faults stored in the vehicle: ? 160020 Crankshaft sensor, signal: implausible ? 180001 Catalytic converter: efficiency too low ? 200D0C Powertrain, safety function: bus signal rpm reduction implausible ? 11A002 Fuel high pressure, plausibility: Pressure too low ? 1F054D Powertrain, safety function: powertrain reduced power, DSC-signal implausible? 120408 Boost pressure control: Shut-down as a consecutive reaction"

NHTSA · bulletin constructeur10147698Années modèle 2016Affiché en anglais d’origine · traduction en attenteVoir le détail →
Hatch III · 2013–2024
BulletinModéréBoîteNA

Bulletin

"B38, B46, and B48 Engines: Clutch Operation, Engine Noise, and Drivability Complaints. The vehicle exhibits one the following complaints: ? The customer notices an increased level of ""free play"" in the clutch pedal when changing gears. ? The clutch pedal remains depressed and will not return to the disengaged position. ? Noise from the lower engine area described as a high-pitched whine ? Loss of power when idling ? At a higher engine speed (above 3,000 rpm), a brief decrease in the engine speed can be felt. ? Extended cranking before the engine will start ? Emergency operation is active with one or more of the faults listed below. Faults stored in the vehicle: ? 160020 Crankshaft sensor, signal: implausible ? 180001 Catalytic converter: efficiency too low ? 200D0C Powertrain, safety function: bus signal rpm reduction implausible ? 11A002 Fuel high pressure, plausibility: Pressure too low ? 1F054D Powertrain, safety function: powertrain reduced power, DSC-signal implausible? 120408 Boost pressure control: Shut-down as a consecutive reaction."

NHTSA · bulletin constructeur10147224Années modèle 2016Affiché en anglais d’origine · traduction en attenteVoir le détail →
Hatch III · 2013–2024
BulletinModéréBoîteNA

Bulletin

F54 ALL4: FAULT CODE 440317 STORED IN THE LMV. The following Check Control Message (CCM) is displayed in the instrument cluster: CCM 350: Driving stabilization. Drive at a moderate speed. The following entry is present in the fault memory of the LMV: 440317 - Pump motor: General multiple fault. Further fault memory entries can occur in combination: DSC: 48068C - Transfer box - clutch closed down temporarily, possible overheating. 48078A - All-wheel drive clutch - clutch position open, only front-wheel drive. LMV: 440304 - Pump motor: Current too low Unfavorable software of the longitudinal torque distribution module (LMV).

NHTSA · bulletin constructeur10146975Années modèle 2016–2017Affiché en anglais d’origine · traduction en attenteVoir le détail →
Hatch III · 2013–2024
BulletinModéréBoîteNA

Bulletin

Mini: Due to faulty installation of crankshaft sensor, catalytic converter, powertrain, fuel high pressure, and boost pressure control, customer complaints of noise from lower engine, loss of power, decrease in engine speed and depressed clutch pedal. *ma

NHTSA · bulletin constructeur10059110Années modèle 2016Affiché en anglais d’origine · traduction en attenteVoir le détail →
Hatch II · 2006–2013
BulletinModéréBoîteNA

Bulletin

Bmw(mini): Transmission - various egs faults caused by wiring harness damage. Difficult to engage the d or r gears from park position; gear shifts are extremely harsh during drive; intermittently the transmission warning light may be displayed. *pe

NHTSA · bulletin constructeur10026570Années modèle 2008Affiché en anglais d’origine · traduction en attenteVoir le détail →
Hatch III · 2013–2024
BulletinMineurBoîteNA

Bulletin

Un message Check Control s’affiche pour l’entretien d’huile de la transmission requis (ID 2120). Cet avertissement peut être déclenché : de 60 000 miles (95 000 km) à 78 000 miles (125 000 km) Après six ans : L’intervalle de six ans commence à partir de la date de production du véhicule, et non le jour de la première immatriculation ou de la vérification préalable à la livraison (PDI). Si le véhicule est conduit à plus d’environ 1900 miles (3 000 km) après le premier CCM, un second message s’affichera comme défaut de transmission ! (ID 368).

NHTSA · bulletin constructeur11032775Années modèle 2024Traduit automatiquement · original : anglaisVoir le détail →
Hatch III · 2013–2024
BulletinMineurBoîteNA

Bulletin

The upper crankshaft guide bearing may wear out prematurely. The wear on the guide bearing can cause the clutch pedal to malfunction during shifting.

NHTSA · bulletin constructeur10216759Années modèle 2014Affiché en anglais d’origine · traduction en attenteVoir le détail →
Hatch III · 2013–2024
BulletinMineurBoîteNA

Bulletin

The upper crankshaft guide bearing may wear out prematurely. The wear on the guide bearing can cause the clutch pedal to malfunction during shifting.

NHTSA · bulletin constructeur10216760Années modèle 2014Affiché en anglais d’origine · traduction en attenteVoir le détail →
Hatch III · 2013–2024
BulletinMineurBoîteNA

Bulletin

When the vehicle is on a lift and wheels are manually spun, a clanking noise is heard from the transmission area.

NHTSA · bulletin constructeur10206695Années modèle 2021Affiché en anglais d’origine · traduction en attenteVoir le détail →
Hatch III · 2013–2024
BulletinMineurBoîteNA

Bulletin

EGS FAULTS STORED AFTER AISIN TRANSMISSION REPLACEMENT. Due to hardware changes in the AISIN GA6F21AW or GA8F22AW transmissions.

NHTSA · bulletin constructeur10163062Années modèle 2016Affiché en anglais d’origine · traduction en attenteVoir le détail →
Hatch III · 2013–2024
BulletinMineurBoîteNA

Bulletin

The manual transmission gear shift knob easily comes off the shift rod with minimal upward force. The retaining tabs on the shifter knob do not hold securely to the shifter rod.

NHTSA · bulletin constructeur10152334Années modèle 2016Affiché en anglais d’origine · traduction en attenteVoir le détail →
Hatch III · 2013–2024
BulletinMineurBoîteNA

Bulletin

"The upper crankshaft guide bearing may wear out prematurely. The wear on the guide bearing can cause the clutch pedal to malfunction during shifting. The Engine Malfunction Warning may be illuminated and a fault will be stored in the DME memory for the crankshaft sensor. Noise may be heard from the lower engine and transmission bell housing area and engine damage can occur in rare occasions. This Service Action involves ""396"" F55 and F56 vehicles produced from January 2014 to February 2015. Vehicles which require this Service Action to be completed will show it as ""Open"" when checked either in the ""Service Menu"" of DCSnet (Dealer Communication System) or with the Key Reader. UN"

NHTSA · bulletin constructeur10151287Années modèle 2015–2016Affiché en anglais d’origine · traduction en attenteVoir le détail →
Hatch III · 2013–2024
BulletinMineurBoîteNA

Bulletin

"SI M11 02 16 February 2016 Engine Technical Service This Service Information bulletin supersedes SI M11 02 16 dated February 2016.. The upper crankshaft guide bearing may wear out prematurely. The wear on the guide bearing can cause the clutch pedal to malfunction during shifting. The Engine Malfunction Warning may be illuminated and a fault will be stored in the DME memory for the crankshaft sensor. Noise may be heard from the lower engine and transmission bell housing area and engine damage can occur in rare occasions. This Service Action involves ""382"" F55 and F56 vehicles produced from February 2014 to December 2014. Vehicles which require this Service Action to be completed will show it as ""Open"" when checked either in the ""Service Menu"" of DCSnet (Dealer Communication System) or with the Key Reader. UN"

NHTSA · bulletin constructeur10151150Années modèle 2015–2016Affiché en anglais d’origine · traduction en attenteVoir le détail →
Hatch III · 2013–2024
BulletinMineurBoîteNA

Bulletin

?SUBJECT Service Action: Program Control Units (DME) . A Check Control Message could intermittently be displayed indicating a Start/Stop Function failure. Vehicle may not restart after stopping. The following fault is stored in the DME: Fault 20BA20: clutch switch, signal: missing In addition the BDC may have the following fault stored: Fault 804084: clutch switch, plausibility fault compared to CAN signal This can occur if for example 14 gears changes are made, but the upper clutch position switch is only activated 10 times. This difference could occur when the clutch pedal is not being fully released between gear shifts or by resting a foot on the pedal so the upper switch position is not recognized.

NHTSA · bulletin constructeur10151046Années modèle 2016Affiché en anglais d’origine · traduction en attenteVoir le détail →
Hatch III · 2013–2024
BulletinMineurBoîteNA

Bulletin

Clutch Is Slipping or Grabbing. The customer states that the clutch is slipping or grabbing.

NHTSA · bulletin constructeur10150145Années modèle 2013Affiché en anglais d’origine · traduction en attenteVoir le détail →
Hatch III · 2013–2024
BulletinMineurBoîteNA

Bulletin

B38 and B48 Engines: Grease Residue Found at Bottom of Transmission Bell Housing. INFORMATION While performing repairs to the underside of the vehicle, the technician may notice yellow grease residue has formed on the lowest point of the transmission bell housing near the engine starter. The residue is not related to the engine oil or transmission fluid. The grease was applied to the starter during vehicle assembly. If the residue is noticed, the grease can be wiped away with a shop towel. The residue will stop accumulating after the engine has been operated for a few hundred miles. If the residue were to drip from the bell housing, it would be caught by the under body covering and would not create a customer complaint. In a severe case, some marks may be seen on the engine side of the under body covering. The grease drippings will not be seen on the ground under the vehicle. Do not remove or replace any components.

NHTSA · bulletin constructeur10148295Années modèle 2014Affiché en anglais d’origine · traduction en attenteVoir le détail →
Hatch III · 2013–2024
BulletinMineurBoîteNA

Bulletin

"Engine Power Reduction with ""Clutch Damaged"" Faults Stored. A drivetrain malfunction check control message is displayed, prompting the customer to contact the dealer for a service visit. The vehicle drives normally, but fault(s) for a damaged clutch are stored in the DME. ? 1D3101 - Clutch: Damaged, transmittable torque too low ? 1D3201 - Clutch: Severely damaged, transmittable torque too low CAUSE 1. The DME software diagnostic for detecting excessive clutch slip is too sensitive. 2. The clutch is damaged."

NHTSA · bulletin constructeur10147741Années modèle 2016Affiché en anglais d’origine · traduction en attenteVoir le détail →
Hatch III · 2013–2024
BulletinMineurBoîteNA

Bulletin

"eAutomatic Transmission Selector Lever Will Not Move Out of Park. The transmission selector lever cannot be disengaged from the ""P"" position. This can occur very randomly and is difficult to reproduce. No faults are stored in the EGS control unit, and no warnings are displayed in the instrument cluster. For the most part, if the vehicle is locked and goes to sleep (the light in the hazard switch goes out), the problem is no longer present. Unfavorable EGS software"

NHTSA · bulletin constructeur10147111Années modèle 2016Affiché en anglais d’origine · traduction en attenteVoir le détail →
Hatch III · 2013–2024
BulletinMineurBoîteNA

Bulletin

Service Action: B38 Engine - Check and Replace Crankshaft Guide Bearing. The upper crankshaft guide bearing may wear out prematurely. The wear on the guide bearing can cause the clutch pedal to malfunction during shifting. The Engine Malfunction Warning may be illuminated and a fault will be stored in the DME memory for the crankshaft sensor. Noise may be heard from the lower engine and transmission bell housing area and engine damage can occur in rare occasions.

NHTSA · bulletin constructeur10146973Années modèle 2016Affiché en anglais d’origine · traduction en attenteVoir le détail →
Hatch III · 2013–2024
BulletinMineurBoîteNA

Bulletin

Service Action: B46 and B48 Engines - Check and Replace Crankshaft Guide Bearing. The upper crankshaft guide bearing may wear out prematurely. The wear on the guide bearing can cause the clutch pedal to malfunction during shifting. The Engine Malfunction Warning may be illuminated and a fault will be stored in the DME memory for the crankshaft sensor. Noise may be heard from the lower engine and transmission bell housing area and engine damage can occur in rare occasions.

NHTSA · bulletin constructeur10146867Années modèle 2016Affiché en anglais d’origine · traduction en attenteVoir le détail →
Hatch III · 2013–2024
BulletinMineurBoîteNA

Bulletin

GROANING NOISE WITH CLUTCH OPERATION. Clutch operation may exhibit the following characteristics: produces a groaning noise, especially when engine is at operating temperature, during stopand-go travel. noise comes from transmission housing. noise can be heard in the interior and exterior of the vehicle. Friction between clutch slave cylinder piston rod end and ball socket (thrust piece).

NHTSA · bulletin constructeur10146870Années modèle 2016Affiché en anglais d’origine · traduction en attenteVoir le détail →
Hatch III · 2013–2024
BulletinMineurBoîteNA

Bulletin

Service Action: B38 Engine - Check and Replace Crankshaft Guide Bearing. The upper crankshaft guide bearing may wear out prematurely. The wear on the guide bearing can cause the clutch pedal to malfunction during shifting. The Engine Malfunction Warning may be illuminated and a fault will be stored in the DME memory for the crankshaft sensor. Noise may be heard from the lower engine and transmission bell housing area and engine damage can occur in rare occasions.

NHTSA · bulletin constructeur10146800Années modèle 2016Affiché en anglais d’origine · traduction en attenteVoir le détail →
Plus anciens →

Sources : NHTSA (États-Unis, domaine public), Transports Canada (Licence du gouvernement ouvert – Canada), DVSA (Royaume-Uni, Open Government Licence v3.0), RappelConso et Safety Gate de l'UE (France, Licence Ouverte 2.0), MLIT (Japon, licence de données publiques 1.0) et MOLIT (Corée du Sud, car.go.kr).