Vehicle speed control
On certain pickup trucks, passenger vehicles, sport utility vehicles, and motor homes chassis, the speed control deactivation switch may, under certain conditions, leak internally and then overheat, smoke, or burn.
🔔 無料アカウントを作成して Mercury カプリ (すべての世代) のメール通知を受け取る
On certain pickup trucks, passenger vehicles, sport utility vehicles, and motor homes chassis, the speed control deactivation switch may, under certain conditions, leak internally and then overheat, smoke, or burn.
The transmission fluid rubber tube connecting the transmission to the transmission oil cooler located in the radiator can become disconnected from the transmission, resulting in discharge of transmission fluid.
長時間の日光への曝露により、ロックバーを保持するフロントシートベルトのタング組立品のプラスチック製スリーブが劣化し、位置がずれる場合があります。その結果、タングがシートベルトのウェビングから外れる可能性があり、乗員にとってシートベルトが機能しなくなるおそれがあります。 是正措置:オーナーには、フォードがこの状態のシートベルトを修理することが通知されます。
The plastic sleeve in the front safety belt tongue assembly which retains the lock bar can deteriorate from prolonged exposure to sunlight and become displaced, causing the tongue to detach from the safety belt webbing.
The rubber tube that connects the transmission to the transmission oil cooler (in the radiator) may disconnect causing discharge of fluid.
EFIまたはCFIを搭載した車両では、燃料供給ラインとリターンラインをEFIフューエルレールまたはCFIスロットルボディに接続するために使用されているスプリングロック式燃料ラインカプラーや、一部の車両でダッシュパネル付近にあるその他の燃料ラインの接続部が、車両使用中に外れる可能性があります。この状態が発生すると燃料漏れが生じ、車両火災の原因となるおそれがあります。 是正措置:対象車両にはカップリング固定クリップが取り付けられます。 注:Escort車両はEFIとCFIの両方を搭載しています。Lynx車両はCFIのみを搭載しています。 EFI - 電子制御燃料噴射 CFI - 中央燃料噴射
The tandem power brake booster rear shells may have been produced with reduced wall thicknesses. Repeated brake applications could cau se such a shell to crack and the booster assembly to come apart.This could result in a total loss of braking capabilty without prior warn ing and present the possibility for loss of control and vehicle cras h.
エアバッグモジュールは、高温環境下での性能に関するFordの仕様を満たしていません。
The forward screw which provides part of the attachment between the driver`s seat back assembly and the seat cushion frame could fracture and permit the driver's seat back to pivot rearward. Such a condition could adversely affect the driver's ability to control the vehicle and could result in a vehicle crash. Correction: New driver's seat cushion attachment screws will be installed on affected vehicles.
Brake booster rear shells may have reduced wall thicknesses which could cause the shell to break. Consequence of defect: Repeated brake use could cause the shell to crack and the booster assembly to come apart. Service brakes capability would be totally lost without warning and could result in an accident.
副スロットル軸は、走行距離が増えるにつれて汚れが蓄積し、走行中に半開の位置で固着することがあります。
Carburetor throttle shafts may be susceptible to dirt contamination and wear of the bearing coatings. This could cause the secondary throttle plates to remain partially open after the driver has released the accelerator pedal. This this were to occur, engine speed would not return to idle potentially affecting vehicle control and stopping distances.
The bolts that attach the d-shaped ring for the shoulder belt are inadequately supported by the material in which they are mounted. The attachment does not comply with the requirements of federal motor vehicle safety standard no. 210, "seat belt assembly anchorages".
The upper torso restraint d-ring which attaches the shoulder belt to the b pillar, under certain test conditions, separated from its anchorage, and may not comply with cmvss 210 - belt anchorage.
Some of the vehciles affected by the recall may have been produced with incorrect hoods - the incorrect hoods were intended for use with conventional (non-turbo) engines and maynot provide a sufficient clearnace between the throttle linkage and the hood undersides. As a result, under certain conditions, the throttle linkage may come in contact with the hood potentially causing damage to the linkage and preventing the throttle from returning to its idle position.
Inadequate clearance between the underside of the hood and the throttle linkage could damage the linkage and prevent the throttle from returning to idle position. This condition is due to installation of the incorrect hood style during vehicle assembly.
These vehicles do not comply with cmvss 209 - seat belt assemblies.
The housing plates on the driver seat back latch recliner assemblies were manufactured with substandard material products. This tainted steel was used to produce seatback latches for both the right and left side seat assemblies. Under certain conditions, the defective housing plates may distort, allowing the locking teeth to disengage and tear off. This permits the seatback to pivot backwards.
Vehicles produced at dearborn assembly plant. Vehicles may have been equipped with driver seat back latch recliner assemblies that contain housing plates manufactured from suspect steel material. Under certain types of driver induced seat loading the recliner mechanism housing plates might distort allowing the locking teeth to disengage. This would allow the seat back to rotate rearward into a reclined position.
Vehicles equipped with turbocharged 2.3l engines and manual transmissions. Vehicles may have been built without a particular electric curcuit in the idle tracking system wiring harness. This condition may cause exhaust emissions of hydrocarbon (hc) and carbon monoxide (co) gases to exceed the limits specified by canada motor vehicle safety standard 1103 - exhaust emissions.
During the railcar chain-down operation or during in-transit railcar movement, the chain could interfere with and break the evaporative emission carbon canister. These vehicles would then not comply with canada motor vehicle safety standard 1105 - evaporative emissions.
注意:3.8リッターエンジン搭載車両。これらの車両は、C.M.V.S.S. 1103(排出ガス)に適合しない可能性があります。触媒内の基材が通常使用中に振動して破損し、排出ガスが基準値を超える場合があります。是正措置:車両を点検し、必要に応じて触媒を交換します。
一部の1987~89年式 Mustang 2.3リッター、1986年式 Mustang および Capri 5.0リッター HO、ならびに1987~89年式 Mustang および Mark VII 5.0リッター HO。これらの車両は C.M.V.S.S. 1103 - 排気ガス排出に適合していない可能性があります。触媒内の担体が通常使用中に振動して破損し、排気ガス排出量が基準値を超える場合があります。是正措置:必要に応じて触媒を交換します。
出典:NHTSA(米国、パブリックドメイン)、カナダ運輸省(Open Government Licence – Canada)、DVSA(英国、Open Government Licence v3.0)、RappelConso および EU Safety Gate(フランス、Licence Ouverte 2.0)、国土交通省(日本、公共データ利用規約1.0)、韓国国土交通部(car.go.kr)。