On certain 318I, 318IC, 318IS, 325IC, 325IS, 325IX, 525I, 535I, 735I and 735IL vehicles, the fuel feed hose could harden and "set" over time due to engine compartment temperatures. If this "setting" occurs, it is possible that seepage between the hose and fitting could result because the clamp cannot provide sufficient sealing force to compensate for the hardening of the hose. Fuel seepage, in the presence of an ignition source, could result in an engine compartment fire. Correction: fuel feed hoses and associated clamps will be replaced with ones of a new design.
Transport Canada30. Mai 19941994096Modelljahre 1989–1993Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Feed fuel hoses can harden and "set" over time, allowing a seepage of fuel at the connection between the hose and the engine fitting. The clamp used to hold the hose to the fitting is unable to compensate for the hardening of the feed fuel hose.
Vehicle description: Passenger vehicles. A malfunction or failure of a coolant system component, such as a thermostat, water pump, or fan belt, can result in significantly increased coolant temperature and system pressure. If the indications of a critical overheating condition is not noticed by the driver, it is possible that damage to, or failure of, a coolant system component could occur.
NHTSA · USA4. Aug. 199898V178000Modelljahre 1988–1993Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Bei bestimmten 318IC, 318IS, 318TI, 325I, 325IC, 325IS, 525I, 525IT, 530I, 530IT, 540I, 740I, 740IL, 840CI und M3 sind Tempomat und Drosselkabel am selben Drosselklappenventilhebel am Drosselgehäuse befestigt. Es ist möglich, dass die Kunststoffbuchse eines der Kabels bricht und das äußere Kabelgehäuse sich von der Buchse löst. Ein Gaspedal ohne Tempomat kann dazu führen, dass das äußere Rohr am Rand der gebrochenen Buchse hängen bleibt und das Drosselklappen teilweise offen bleibt. Falls dies passiert, könnte das Auto nicht wie erwartet abbremsen und ein Aufprall könnte einschlagen. Korrektur: Am äußeren Rohr jedes Kabels wird ein Federclip angebracht, um ein Lösen von der Buchse zu verhindern.
The cruise control and throttle cables are attached to the same throttle valve actuating lever at the throttle housing. It is possible that the plastic bushing on either cable could break due to environmental influences coupled with vibration. If the bushing breaks, the outer cable housing can separate from the bushing. In this case, during application of the throttle pedal without cruise control being engaged, the outer tube could catch on the edge of the broken bushing.
NHTSA · USA19. Aug. 199797V131000Modelljahre 1993Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
On certain 740IA and 740ILA vehicles, the inner throttle cable could break due to a smaller than specification bend in the cable tube. If this were to occur, throttle control would be lost and the engine would return to or remain at idle. Correction: Throttle cable will be replaced with one meeting BMW specifications.
Transport Canada25. Apr. 19941994081Modelljahre 1993Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
On certain 535I, 535IA, 735IA, 735ILA vehicles, the nut which secures the throttle valve shaft may not have been tightened with sufficient torque. If the nut were to loosen, it is possible that movement of the throttle valve might be impaired. If this should occur, the vehicle might not decelerate as expected after the gas pedal is released and loos of vehicle control could result. Correction: Vehicles will be inspected and affected throttle housings with undertorqued throttle valve retaining nuts will be replaced.
Transport Canada13. Okt. 19921992129Modelljahre 1991Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
On certain 750IL vehicles, during the assembly process, the gas pedal may not have been properly attached to the floor pan. If the gas pedal is operated in a rough or erratice manner, it may become stuck between the gas pedal stop (on the floor pan) and the carpeting on the transmission tunnel. If this occurs, the pedal might not return fully to the idle position when the driver's foot is removed and loss of control could result. Application of the brake pedal will close the throttle on this model of vehicle. Correction: Accelerator pedal will be inspected and tightened to the floor is required. Also, a modified pedal stop will be installed.
Transport Canada6. Apr. 19891989046Modelljahre 1988–1989Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
Quellen: NHTSA (USA, gemeinfrei), Transport Canada (Open Government Licence – Canada), DVSA (Vereinigtes Königreich, Open Government Licence v3.0), RappelConso und EU-Safety-Gate (Frankreich, Licence Ouverte 2.0), MLIT (Japan, Public Data License 1.0) und MOLIT (Südkorea, car.go.kr).