Frei lesbar · kostenloses Konto zum MitmachenNachfolger von Anticars (2000)

BMW 7er E32

1986–1994 · 5 dokumentierte Mängel · 4 Märkte
Modelljahr
MarktAlleNA
RückrufKritischInnenraumNA

Airbag

On certain 318I, 318IS, 325I, 325IS, 525I, 525IT, 535I, 735I, 735IL, 750IL, 850I and M5, the locking tab for the airbag contact ring in the steering wheel assembly could break without warning. If this happens it is possible that the contact ring wiring could break. This would cause the readiness indicator lamp ("SRS" or "AIRBAG") to illuminate and in such a case the airbag would not be available for deployment in a frontal impact. Correction: Locking tab will be replaced with one of a different design.

Transport Canada7. Okt. 19961996159Modelljahre 1991–1992Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
RückrufKritischInnenraumNA

Air bags:Frontal

The air bag contact ring locking tab located in the steering wheel assembly can break without warning.

NHTSA · USA1. Juli 199696V110000Modelljahre 1991–1992Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
RückrufKritischMotorNA

Fuel System

On certain 318I, 318IC, 318IS, 325IC, 325IS, 325IX, 525I, 535I, 735I and 735IL vehicles, the fuel feed hose could harden and "set" over time due to engine compartment temperatures. If this "setting" occurs, it is possible that seepage between the hose and fitting could result because the clamp cannot provide sufficient sealing force to compensate for the hardening of the hose. Fuel seepage, in the presence of an ignition source, could result in an engine compartment fire. Correction: fuel feed hoses and associated clamps will be replaced with ones of a new design.

Transport Canada30. Mai 19941994096Modelljahre 1989–1993Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
RückrufKritischMotorNA

Fuel system, gasoline:Delivery:Hoses, lines/piping, and fittings

Feed fuel hoses can harden and "set" over time, allowing a seepage of fuel at the connection between the hose and the engine fitting. The clamp used to hold the hose to the fitting is unable to compensate for the hardening of the feed fuel hose.

NHTSA · USA11. Apr. 199494V066000Modelljahre 1989–1993Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
RückrufMittelInnenraumNA

Heizung und Defroster

Bei bestimmten Fahrzeugen kann der Ausfall einer Kühlsystemkomponente, etwa des Thermostats, der Wasserpumpe oder des Keilriemens, zu einem deutlichen Anstieg der Kühlmitteltemperatur und des Systemdrucks führen. Der erhöhte Systemdruck könnte die Bildung eines Risses oder das Auftrennen einer Naht im Endstück des Heizungskühlers verursachen, wodurch heißes Kühlmittel aus dem Heizungskühler austreten könnte. Diese heiße Flüssigkeit könnte mit den Fahrzeuginsassen in Berührung kommen, was möglicherweise zu Verletzungen führen und/oder die Innenseiten der Fensterflächen beschlagen lassen kann. Abhilfe: Der Kühlerdeckel wird durch einen Deckel neuer Bauart ersetzt, um einen übermäßigen Druckaufbau im Kühlsystem zu vermeiden.

Transport Canada14. Okt. 19981998197Modelljahre 1988–1993Automatisch übersetzt · Original: EnglischDetails ansehen →
RückrufMittelMotorNA

Engine and engine cooling:Cooling system

Vehicle description: Passenger vehicles. A malfunction or failure of a coolant system component, such as a thermostat, water pump, or fan belt, can result in significantly increased coolant temperature and system pressure. If the indications of a critical overheating condition is not noticed by the driver, it is possible that damage to, or failure of, a coolant system component could occur.

NHTSA · USA4. Aug. 199898V178000Modelljahre 1988–1993Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
RückrufMittelMotorNA

Motor

Bei bestimmten 318IC, 318IS, 318TI, 325I, 325IC, 325IS, 525I, 525IT, 530I, 530IT, 540I, 740I, 740IL, 840CI und M3 sind Tempomat und Drosselkabel am selben Drosselklappenventilhebel am Drosselgehäuse befestigt. Es ist möglich, dass die Kunststoffbuchse eines der Kabels bricht und das äußere Kabelgehäuse sich von der Buchse löst. Ein Gaspedal ohne Tempomat kann dazu führen, dass das äußere Rohr am Rand der gebrochenen Buchse hängen bleibt und das Drosselklappen teilweise offen bleibt. Falls dies passiert, könnte das Auto nicht wie erwartet abbremsen und ein Aufprall könnte einschlagen. Korrektur: Am äußeren Rohr jedes Kabels wird ein Federclip angebracht, um ein Lösen von der Buchse zu verhindern.

Transport Canada9. Okt. 19971997173Modelljahre 1993Automatisch übersetzt · Original: EnglischDetails ansehen →
RückrufMittelMotorNA

Vehicle speed control

The cruise control and throttle cables are attached to the same throttle valve actuating lever at the throttle housing. It is possible that the plastic bushing on either cable could break due to environmental influences coupled with vibration. If the bushing breaks, the outer cable housing can separate from the bushing. In this case, during application of the throttle pedal without cruise control being engaged, the outer tube could catch on the edge of the broken bushing.

NHTSA · USA19. Aug. 199797V131000Modelljahre 1993Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
RückrufMittelElektrikNA

Lights And Instruments

On certain 325I, 325IC, 325IS, 525I, 525IT, 530I, 530IT, 535I, 540I, 735I, 735IL, 740I, 740IL and 750I, the brake light switch may fail due to a reduction of contact force on the "snap contact" system which the switch incorporates. This could cause heat induced distortion of the plastic internal switch parts in the area of the electrical contacts. This could cause the switch to remain either in the ON or the OFF position resulting in the brake lights being continuously illuminated or inoperative regardless of brake pedal operation. Correction: Switch will be replaced with on that utilizes a different contact system.

Transport Canada7. Okt. 19961996158Modelljahre 1990–1993Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
RückrufMittelBremsenNA

Exterior lighting:Brake lights:Switch

The brake light switch can fail allowing the switch to remain in the "brake lights off" position or in the "brake lights on" position.

NHTSA · USA1. Juli 199696V111000Modelljahre 1990–1993Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
RückrufMittelMotorNA

Engine

On certain 740IA and 740ILA vehicles, the inner throttle cable could break due to a smaller than specification bend in the cable tube. If this were to occur, throttle control would be lost and the engine would return to or remain at idle. Correction: Throttle cable will be replaced with one meeting BMW specifications.

Transport Canada25. Apr. 19941994081Modelljahre 1993Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
RückrufMittelMotorNA

Vehicle speed control:Cables

The throttle cable's tube (outer casing) contains a bend that leads to increased loading of the inner cable, causing it to break.

NHTSA · USA3. Jan. 199494V022000Modelljahre 1993Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
RückrufMittelMotorNA

Engine

On certain 535I, 535IA, 735IA, 735ILA vehicles, the nut which secures the throttle valve shaft may not have been tightened with sufficient torque. If the nut were to loosen, it is possible that movement of the throttle valve might be impaired. If this should occur, the vehicle might not decelerate as expected after the gas pedal is released and loos of vehicle control could result. Correction: Vehicles will be inspected and affected throttle housings with undertorqued throttle valve retaining nuts will be replaced.

Transport Canada13. Okt. 19921992129Modelljahre 1991Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
RückrufMittelMotorNA

Vehicle speed control

Some of these vehicles are equipped with a throttle housing on which the throttle valve shaft retaining nut was not sufficiently tightened.

NHTSA · USA10. Juli 199292V101000Modelljahre 1991Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
RückrufMittelInnenraumNA

Seats And Restraints

On certain 525I, 535I, 735I, 735IL and 750IL vehicles, the front seat center fold-down armrest may contact and damage the seatbelt buckle if the seat back is moved forward to an upright position while the armrest is locked in the down position (horizontal). If this occurs, the release button may be held in the down position, preventing the seatbelt from being latched during the buckle-up operation. Non-latching of the seatbelts will increase the risk of personal injury in the event of a crash. Correction: Front seat safety belt buckles will be replaced with shorter ones that are not susceptible to damage by contact with the armrest.

Transport Canada27. Feb. 19901990037Modelljahre 1988–1990Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
RückrufMittelInnenraumNA

Seat belts:Front:Buckle assembly

Under certain conditions, front seat center, fold-down arm rest may contact the safety belt buckle, causing damage to the release button and preventing the belt tongue from latching when buckling up.

NHTSA · USA30. Jan. 199090V016000Modelljahre 1988–1990Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
RückrufMittelMotorNA

Emissions

Certain 750IL vehicles fail to comply with the requirements of CMVSS 1103 - Exhaust Emissions.

Transport Canada2. Mai 19891989063Modelljahre 1988–1989Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
RückrufMittelMotorNA

Emissions

Certain 750IL vehicles fail to comply with the requirements of CMVSS 1103 - Exhaust Emissions

Transport Canada2. Mai 19891989062Modelljahre 1988–1989Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
RückrufMittelMotorNA

Engine

On certain 750IL vehicles, during the assembly process, the gas pedal may not have been properly attached to the floor pan. If the gas pedal is operated in a rough or erratice manner, it may become stuck between the gas pedal stop (on the floor pan) and the carpeting on the transmission tunnel. If this occurs, the pedal might not return fully to the idle position when the driver's foot is removed and loss of control could result. Application of the brake pedal will close the throttle on this model of vehicle. Correction: Accelerator pedal will be inspected and tightened to the floor is required. Also, a modified pedal stop will be installed.

Transport Canada6. Apr. 19891989046Modelljahre 1988–1989Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
RückrufMittelElektrikNA

Electrical

On certain 325E, 325ES, 528E, 535I, 635CSI and 735I vehicles, the center high mounted brake light could add sufficient electrical load to cause the brake light switch to overheat, eventually leading to melting of the plastic internal switch parts. This could cause the switch plunger to jam in the ON or OFF position. This would render the brake light permanently ON or OFF regardless of brake pedal operation. Correction: A brake light switch with an increased current load capacity will be installed on affected vehicles.

Transport Canada27. Nov. 19861986134Modelljahre 1986–1987Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
RückrufMittelBremsenNA

Exterior lighting:Brake lights:Switch

Brake light switch could overheat, eventually leading to melting of plastic internal parts in area of electrical contacts.

NHTSA · USA10. Nov. 198686V151000Modelljahre 1986–1987Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
RückrufGeringInnenraumNA

Seats And Restraints

On certain 725I, 735IA and 750IL vehicles, on the front seats, the seatbacks may not have been fully seated on the recliner arms. This could result in looseness of, or noise in the seat. In extreme cases, during a severe rear impact, the seatback may not support the occupant and increase the risk of injury. Correction: Seatbacks will be inspected and properly seated if required.

Transport Canada25. Aug. 19881988124Modelljahre 1988Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →
RückrufGeringInnenraumNA

Seats

The driver and/or passenger seatbacks may not have been fully attached to the seat base reclining arms (attaching brackets).

NHTSA · USA11. Aug. 198888V135000Modelljahre 1988Im Original (Englisch) angezeigt · Übersetzung ausstehendDetails ansehen →

Quellen: NHTSA (USA, gemeinfrei), Transport Canada (Open Government Licence – Canada), DVSA (Vereinigtes Königreich, Open Government Licence v3.0), RappelConso und EU-Safety-Gate (Frankreich, Licence Ouverte 2.0), MLIT (Japan, Public Data License 1.0) und MOLIT (Südkorea, car.go.kr).